DAQ system USB-EK01 Manuale utente
http://www.daqsystem.co
m
USB-EK01 Users Manual (Rev 1.0)
- 1 -
USB-EK01
User Manual
AN2131, EZ-USB and Cypress are trademarks of Cypress Semiconductor, Keil and uVision2 are trademarks of
Keil software. Windows, Windows2000, Windows NT and Windows XP are trademarks of Microsoft. We
acknowledge that the trademarks or service names of all other organizations mentioned in this document as their
own property.
The information in this document is subject to change without notice and no part of this document may be copied
or reproduced without the prior written consent.
Copyrights 2005 DAQ system, All rights reserved.
http://www.daqsystem.co
m
USB-EK01 Users Manual (Rev 1.0)
- 2 -
Contents
1. Introduction
2. USB-EK01 Function & Specification
3. Installation
3.1 Confirm Product Contents
3.2 Cypress Development kit Installation
3.3 Board Driver Installation
4. USB-EK01 Description
4.1 USB-EK01 Concept
4.2 Memory Map
4.2.1 EK01 Memory map
4.2.2 IK01 Memory Map
4.3 Booting Option
4.4 CDROM Folder
5. Test
5.1 Example
5.2 Program & Debugging with KeiluVision
5.3 USB Firmware
5.4 Make USB PC Driver
5.5 Make EEPROM Image
5.6 Application Program for PC
Appendix
A Driver Installation & Remove
B Board connector PIN map
C Notice
Reference
http://www.daqsystem.co
m
USB-EK01 Users Manual (Rev 1.0)
- 3 -
1. Introduction
SW1
SW2
SW3
JP5
(USB B type
Connector)
DAQ system
D1 D2 D3
JP1(Boare Extention)
JP7(Boare Extention)
P1
RS232
connection
JP4
JP6
JP3
JP2
AN2131
D4
www.daqsystem.com
Reset
Power
[Figure 1-1. USB-EK01 Out-side View]
Above picture views board out-side, it display Reset switch and Power LED which
light on when power supply with connection cable. More specific information refer to
“4.1 USB-EK01 Concept”.
http://www.daqsystem.co
m
USB-EK01 Users Manual (Rev 1.0)
- 4 -
2. USB-EK01 Function & Specification
<Function>
- USB Protocol Test & Development
- 8051 Program Test & Development
- PC용USB device driver Test & Development
- Step by Step Debugging Practice
<Specification>
- Full speed (12Mbps) USB Support
- Advanced using 8051 core Micro-Controller
- Convenient Interface USB SIE (Serial Interface Engine)
- Step by Step Debugging & 8051 Compile Test (Code size limited 4K)
- Power Supply through USB Cable (Max. 500mA)
- Two RS232 interface (Maximum transfer speed-115200bps) Debugging or
It can use special purpose.
- Board Reset & Firmware Program Load through USB
- Easy device development through Cypress의Development Kit
- Usable evaluation Keil Compiler & Debugger (Limit 4K code)
http://www.daqsystem.co
m
USB-EK01 Users Manual (Rev 1.0)
- 5 -
3. Installation
3.1 Confirm Product Contents
[Figure 3-1. USB-EK01 Main Contents]
(1) USB-EK01 Evaluation board
(2) USB (A-B) Cable
(3) 9Pin Null Modem cable
(4) CD (Manual/Schematic/Sample test etc..)
3.2. Cypress Development kit Installation
A development and exercise of board refer to mainly Development Kit at Cypress,
you can get a lot of information and report. You can use the ”Development kit”to
download at homepage of Cypress. (“www.cypress.com”) The “Development kit “is a
software package minimum 60Mbyte size, If it install, the folder structure is as follows.
http://www.daqsystem.co
m
USB-EK01 Users Manual (Rev 1.0)
- 6 -
[Figure 3-2. Folder Structure]
[Notice] If you want a Keil software and separate reference report, you shall select a
custom install option not default.
You confirm a folder at your PC as above picture when normally finished install.
The Cypress Development Kit include Keil compiler and debugger, you can freely use
a code size of 4K byte in range not business purpose.
http://www.daqsystem.co
m
USB-EK01 Users Manual (Rev 1.0)
- 7 -
3.3 Board Driver Installation
(Notice) All test made a Windows2000 Professional with bases, we are having finished
the final test at Windows XP.
Execute “Device Manager”at My Computer -> Properties -> Hardware -> Device
Manager window.
[Figure 3.3 Select “My computer”->”Properties”]
[Figure 3.4 “Device Manager” window]
http://www.daqsystem.co
m
USB-EK01 Users Manual (Rev 1.0)
- 8 -
Figure 3.4 shows that “Device Manager”execution window. You can check all USB
device connection at your PC. Currently not yet connect “USB-EK01”, it is not
marked.
[Figure 3.5 USB-EK01 Connection]
The USB-EK01 is connected to PC through USB cable after jumper setting like
above red circle. The reason of using jumper is that an address of EEPROM(24LC64)
is able to recognize it at AN2131. AN2131 is having function of EEPROM information
to connect I2C port can select a lot of booting option when Power On Booting.
Usable EEPROM is same as the following table to a board booting option. Refer to
“I2C Boot Loader”of AN2131 manual for special information.
Bytes EEPROM A2 A1 A0
16 24LC00 N/A N/A N/A
128 24LC01 0 0 0
256 24LC02 0 0 0
4K 24LC32 0 0 1
8K 24LC64 0 0 1
When it is connected to USB cable, “New Hardware Search Wizard”execute
automatically, you can check the USB device at “Device Manager”.
It don’t require another driver because of Cypress Development Kit was installed.
Figure 3.6 will be shown after completely installation. An EEPROM information of board
is as follows at default (when first purchase).
0000h: B0 47 05 80 00 00 00 (Refer to file 2100.iic at Cypress)
That is, Using VID(Vender ID) = 0x547, PID(Product ID)=0x80 in EEPROM will be
registered to PC in an USB device.
http://www.daqsystem.co
m
USB-EK01 Users Manual (Rev 1.0)
- 9 -
[Figure 3.6 A board was registered with default to PC]
If the jumper don’t connect, the screen is as follows. The way that you can confirm,
after remove jumper, reset switch of a board is “ON/OFF”or reconnect a USB cable
after remove. For more specific information, refer to “Chapter 4.3 Booting Option”.
[Figure 3.7 A board was registered to PC without recognition EEPROM]
http://www.daqsystem.co
m
USB-EK01 Users Manual (Rev 1.0)
- 10 -
You confirm to register to PC like figure 3.6 that rebooting a board after connection
jumper. After that, “EZ-USB Control Panel(EzMr.exe)”utility which given Cypress
Development Kit perform.
[Figure 3.8 EZ-USB Control Panel]
(Notice) When development a product at Cypress, Usable utility is searchable in
“Cypress\USB \Bin”and “Cypress\USB\Util”.
The execution screen of “EZ-USB Control Panel(EzMr.exe)”is like figure 3.9.
If connection doesn’t work a device, the error message will be marked.
[Figure 3.9 EZ-USB Control Panel]
Altri manuali per USB-EK01
1
Indice
Altri manuali DAQ system Scheda madre
Manuali Scheda madre popolari di altre marche
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manuale utente
Gigabyte
Gigabyte GA-9IVDT Manuale utente
Texas Instruments
Texas Instruments ADS8372EVM Manuale utente
Commell
Commell MS-C73 Manuale utente
IBT Technologies
IBT Technologies MB860 Manuale utente
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manuale utente
