Datalogic DRAGON D101 Manuale utente

DRAGON™

D SERIES READERS

QUICK REFERENCE

INSTALLAZIONE RAPIDA

INSTALLATION RAPIDE

SCHNELLINSTALLATION

820000852 (Rev. B)

USING DRAGON™ D READERS

DRAGON™ D READERS automatically scan barcodes at a

distance. Simply aim and pull the trigger. Code scanning is

performed along the scan line emitted from the reading

wiindow. This line must cross the entire code.

Successful scanning is obtained by tilting the reader with

respect to the barcode to avoid direct reflections which impair

the reading performance(see the figure above).

I lettori DRAGON™ D leggono i codici a barre a distanza: è

sufficiente mirare sul codice e premere il grilletto. La lettura

avviene sulla linea laser che deve attraversare interamente il

codice da leggere. Le condizioni ottimali per la lettura si

ottengono inclinando il lettore rispetto al codice, così da evitare

riflessioni dirette, che potrebbero compromettere le prestazioni

di lettura (vedere la figura qui sopra).

Les lecteurs DRAGON™ D lisent les codes à distance. Il est

suffisant de viser le code.Le code est lit sur la ligne sortant de

la fenêtre de lecture de l'appareil. Cette ligne doit traverser le

code à barres à lire de part en part.

Pour des prestations optimales inclinez la douchette par

rapport au code à lire, afin d'éviter des réflexions directes qui

pourraient compromettre la performance de lecture (voir la

figure ci-dessus).

Die DRAGON™ D Leser lesen Strichcodes berührungslos. Es

genügt auf den Code zu zielen und abzudrücken. Der Code

wird mittels einer Lichtlinie gelesen, die das Gerät durch das

Lesefenster verläßt und den gesamten Code durchqueren

muß.

Eine optimale Lesegarantie ist gewährleistet, wenn der

Benutzer den Leser bzgl. dem Code etwas neigt, um eine

direkte Reflexion zu vermeiden, wie im Bild oben gezeigt wird.

AIMING SYSTEM

DRAGON™ D101 and DRAGON™ D101 LR models provide a

programmable aiming system. If enabled, the scan line emitted

from the reading window is preceded by a red spot which must

illuminate the code center to get the best reading performance

(see figure above, c). Once the defined timeout is reached, the

red spot disappears and is followed by the scan line to start the

code scanning.

I modelli DRAGON™ D101 e DRAGON™ D101 LR offrono un

sistema di puntamento programmabile. Se attivato, uno spot

rosso illumina il codice precedendo l'emissione della linea

laser. Per ottenere la massima prestazione di lettura è

necessario centrarlo sul codice stesso (vedi figura sopra, c).

Lo spot scomparirà una volta terminato il timeout

precedentemente definito e seguirà l'emissione della linea laser

per avviare la lettura.

Les modèles DRAGON™ D101 et DRAGON™ D101 LR

fournissent un système de pointage programmable. Si le

système est activé, un spot rouge, qui précéde la sortie de la

ligne de lecture, illumine le code à lire. Le spot doit être centré

sur le code pour obtenir la meilleure performance de lecture

(voir la figure ci-dessus, c). Une fois le "timeout" terminé, le

spot rouge est suivi par la ligne de lecture.

Die DRAGON™ D101 und DRAGON™ D101 LR Modelle

bieten ein programmierbares Zielsystem. Wenn das System

ein ist, zuerst verläßt der Leser ein rotes und rundes Licht und

dann die Lichtlinie. Das rundes Licht muß mittels des Codes

sich befinden, um die beste Leseleistung zu erreichen (siehe

Bild oben , c). Wenn das Lichttimeout geendet ist, schaltet das

rotes und rundes Licht ab. Dann verläßt der Leser die Lichtlinie,

um den Code zu lesen.

UK Read one of the following codes to set desired

aiming system timeout.

ILeggere uno dei codici seguenti per impostare il

timeout del sistema di puntamento.

FLire l'un des codes suivants pour sélectionner le

"timeout" du système de pointage que vous désirez.

DLesen Sie einen der folgenden Codes, um das

Zielsystemstimeout einzustellen.

♦

aiming system disabled

i#9"k

300 ms

i#9'k

500 ms

i#9,k

1 sec

i#91k

DATALOGIC S.p.A.,

Via Candini, 2

40012 - Lippo di Calderara

Bologna - Italy

dichiara che

declares that the

déclare que le

bescheinigt, daß das Gerät

declare que el

DRAGON™ D101, Hand-Held Reader

e tutti i suoi modelli

and all its models

et tous ses modèles

und seine modelle

y todos sus modelos

sono conformi alle Direttive del Consiglio Europeo sottoelencate:

are in conformity with the requirements of the European Council Directives listed below:

sont conformes aux spécifications des Directives de l'Union Européenne ci-dessous:

den nachstehenden angeführten Direktiven des Europäischen Rats:

cumple con los requisitos de las Directivas del Consejo Europeo, según la lista

89/336/EEC EMC Directive e 92/31/EEC, 93/68/EEC emendamenti successivi

and further amendments

et ses successifs amendements

und späteren Abänderungen

y succesivas enmiendas

73/23/EEC Low Voltage Directive

Basate sulle legislazioni degli Stati membri in relazione alla compatibilità

elettromagnetica ed alla sicurezza dei prodotti.

On the approximation of the laws of Member States relating to electromagnetic

compatibility and product safety.

Basée sur la législation des Etates membres relative à la compatibilité

électromagnétique et à la sécurité des produits.

Über die Annäherung der Gesetze der Mitgliedsstaaten in bezug auf

elektromagnetische Verträglichkeit und Produktsicherheit entsprechen.

Basado en la aproximación de las leyes de los Países Miembros respecto a la

compatibilidad electromagnética y las Medidas de seguridad relativas al producto.

Questa dichiarazione è basata sulla conformità dei prodotti alle norme seguenti:

This declaration is based upon compliance of the products to the following standards:

Cette déclaration repose sur la conformité des produits aux normes suivantes:

Diese Erklärung basiert darauf, daß das Produkt den folgenden Normen entspricht:

Esta declaración se basa en el cumplimiento de los productos con las siguientes

normas:

EN 55022, August 1994: L

IMITS AND METHODS OF MEASUREMENTS OF

RADIO DISTURBANCE CHARACTERISTICS OF

INFORMATION TECHNOLOGY EQUIPMENT

(ITE)

EN 61000-6-2, April 1999: E

LECTROMAGNETIC COMPATIBILITY

(EMC).

ART

6-2: G

ENERIC

TANDARDS

- I

MMUNITY

FOR INDUSTRIAL ENVIRONMENTS

EN 60825, March 1993: R

ADIATION SAFETY OF LASER PRODUCTS

EQUIPMENT CLASSIFICATION

REQUIREMENTS

AND USER

S GUIDE

Ruggero Cacioppo

Lippo di Calderara, 21/09/2001

Quality Assurance Supervisor

WARRANTY

UK Datalogic warranties this product against defects in

workmanship and materials, for a period of 24

months from the date of shipment, provided that the

product is operated under normal and proper

conditions.

Datalogic has the faculty to repair or replace the

product, these provisions do not prolong the original

warranty term.

The warranty does not apply to any product that has

been subject to misuse, accidental damage,

unauthorized repair or tampering.

IDatalogic garantisce questo prodotto contro difetti di

fabbricazione e di materiali per 24 mesi dalla data di

consegna, a condizione che il prodotto sia utilizzato

come previsto.

Datalogic si riserva la facoltà di riparare o sostituire

il prodotto. Quanto sopra non prolunga la garanzia

originale.

La garanzia non si applica a prodotti utilizzati in

modo non corretto, danneggiati accidentalmente,

sottoposti a riparazioni non autorizzate o

manomessi.

FDatalogic garantit ce produit de tout défaut de

fabrication ou des matériels pendant 24 mois de la

date de livraison, à condition que le produit soit

utlisé correctement.

Datalogic a la faculté de réparer ou de remplacer ce

produit. Ces mesures ne prolongeront pas

l’échéance de la garantie.

La garantie ne s’applique pas aux produits qui ont

été utilisés de façon incorrecte, accidentellement

endommagés, soumis à des réparations non

authorisées ou gâchés.

DDatalogic gibt für dieses Produkt eine Garantie von

2 Jahren auf Herstellungs- und Materialfehler ab

Versandsdatum, falls das Produkt unter normalen

und angemessenen Bedingungen verwendet wurde.

Datalogic behaltet sich vor, das Produkt entweder

zu reparieren oder zu ersetzen, was aber den

originalen Garantietermin nicht verlängert.

Die Garantie ist nicht gültig, falls das Produkt falsch

angewandt, zufällig beschädigt, unberechtigt

repariert oder verändert wird.

TECHNICAL FEATURES

DRAGON™ D101 SERIES

Electrical Features D101 D101 HD D101 LR

Power supply 4 to 20 Vdc

Consumption

@ 4V

@ 5V

@ 20V

Sleep mode

250 mA

170 mA

40 mA

2 mA

Scan rate 35 ± 5 scans/sec

Typical reading field

width

see reading diagrams

Max. resolution

mils

0.08

0.06

2.5

0.25

PCS minimum

(Datalogic Test Chart) 15% 40% 40%

Indicators Laser On LED (red)

Good Read LED (green)

Beeper

Laser Features

Power (max) in mW 0.9 0.4 1.4

Scan angle 42° 37° 23°

Laser Safety Class

EN 60825-1 / CDRH 2

Environmental Features

Working Temperature -10° to

+50 °C

0° to

+40 °C

-10° to

+50 °C

Storage Temperature -20°to +50 °C

Humidity 90% non condensing

Drop resistance IEC 68-2-32 Test ED

Protection sealed against rain and dust

Mechanical Features

Weight (without cable) About 270 g.

Cable length 2 m

DRAGON™ D101 READING DIAGRAMS

DRAGON™ D101

12 24 36 48 60 96

72 84 108 cm

0.19 mm

(7.5 mils)0.25 mm

(10 mils)0.33 mm

(13 mils)

0.50 mm

(20 mils)

1.00 mm

(40 mils)1.38 mm

(55 mils)

0.08 mm

(

3 mils

)

0.13 mm

(5 mils)

0.38 mm

(15 mils)

DRAGON™ D101 - High Density

246810 1412

0.06 mm (2.5 mils)

0.08 mm (3 mils)

0.06 mm

(

2.5 mils

)

0.08 mm

(3 mils)

0.13 mm

(5 mils)0.19 mm

(

7.5 mils

)

16 cm

EAN13 0.33 mm

(13 mils)

EAN13 0.33 mm

(13 mils)

FCC COMPLIANCE

This device complies with PART 15 of the FCC

Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any

interference received, including interference which

may cause undesired operation.

This equipment has been tested and found to comply with the

limits for a Class A digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is

operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instruction

manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own

expense.

3 OPERATING TEST

UK Read the TEST codes below.

ILeggere i codici di test.

FLire les codes tests.

DLesen Sie die Test-Coden.

EAN-8

1234 5670

EAN-13

1 234567 000992

Code 39 (Normal)

17162

Code 128

test

Interleaved 2 of 5

0123456784

DRAGON™ D101 - Long Range

25 50 75 100 125 200 225 cm

150 175

0.38 mm

(15 mils)0.50 mm

(20 mils)

1.00 mm

(40 mils)1.38 mm

(55 mils)

1.00 mm (40 mils)

1.38 mm (55 mils)

0.25 mm

(10 mils)

CONNECTIONS

RS232

WEDGE

PEN

C-BOX

DISCONNECTING THE CABLE

UK YOUR READER IS NOW READY TO READ

BARCODES.

To change the defaults, see the DRAGON™

Reference Manual, part number 90ACC1855.

IIL LETTORE È PRONTO A LEGGERE I CODICI.

Per cambiare i parametri di default, fare riferimento

al manuale "DRAGON™ Reference Manual", n.

d'ordine 90ACC1855.

FVOTRE LECTEUR EST DÉSORMAIS PRÊT A

L’EMPLOI POUR LA LECTURE DE CODES.

Pour changer les paramètres voir le manuel

"DRAGON™ Reference Manual" numéro d'ordre

90ACC1855.

DDAS LESEGERÄT IST JETZT BEREIT CODES ZU

LESEN.

Um die Werkseinstellungsparameter zu ändern,

schlagen Sie im Handbuch "DRAGON™ Reference

Manual" nach, Bestellnummer 90ACC1855.

The following Keyboard Nationality selections are only valid

for IBM AT compatible PCs:

Japanese

i'+k

Russian (Latin)

i'+#k

Russian (Cyrillic)

i'+"Kk

Hungarian

i'+#Pk

Yugoslavian

i'+$Uk

Romanian

i'+%Zk

Czechoslovakian

i'+&_k

1 DEFAULT

UK Read the RESTORE DEFAULT.

ILeggere il codice che ripristina i default.

FLecture du code de configuration par défaut.

DLesen Sie den Restore Default Code, um die

Werkseinstellung wieder herzustellen.

RESTORE DEFAULT

iPk

RS232 DEFAULT SETTINGS

9600 baud, no parity, 8 data bits, 1 stop bit, no

handshaking, delay disabled, rx timeout 5 sec., ack/nack

protocol disabled, FIFO enabled, serial trigger lock

disabled;

DATA FORMAT

: code identifier disabled, no field adjustment,

code length not transmitted, no header, terminator =

CR-LF, character replacement disabled

WEDGE DEFAULT SETTINGS

USA keyboard, caps lock off, num lock unchanged, inter-

character and inter-code delays disabled, control character

emulation = ctrl+shift+key;

DATA FORMAT

: code identifier disabled, no field adjustment,

code length not transmitted, no header, terminator =

ENTER, character replacement disabled

PEN EMULATION DEFAULT SETTINGS

interpret operating mode, conversion to code 39 disabled,

output level normal, idle level normal, minimum output

pulse 600 µs, overflow medium, inter-block delay disabled

POWER SAVE

sleep state disabled

READING PARAMETERS

trigger type = hardware, trigger signal = level, no trigger

timeout, Flash On = 1 sec, Flash Off = 0.6 sec, one read

per cycle, safety time 0.5 sec, beeper intensity high, tone 2,

aiming spot disabled

DECODING PARAMETERS

ink spread enabled, overflow control enabled, interdigit

control enabled, Puzzle Solver™ disabled, decoding safety

= one read

CODE SELECTION

Enabled codes

• EAN 8 / EAN 13 / UPC A / UPC E without ADD ON

check digit transmitted, no conversions

• Interleaved 2/5

check digit control and transmission, variable length

code; 4-99 characters

• Standard Code 39

no check digit control, variable length code; 1-99

characters

• Code 128

variable length code; 1-99 characters

Disabled codes

EAN 128, ISBT 128, Code 93, Codabar,

pharmaceutical codes, Codablock-A, Codablock-F

Standard and EAN, MSI, Plessey, Telepen, Delta IBM,

Code 11, Code 16K, Code 49

ADVANCED FORMATTING PARAMETERS

concatenation disabled, no advanced formats defined

WEDGE KEYBOARD NATIONALITY

UK Wedge users should select one of the following

WEDGE KEYBOARD NATIONALITY codes.

IQuando è selezionata l’interfaccia Wedge, leggere uno

dei seguenti codici per impostare la nazionalità della

tastiera.

FPour l’interface Wedge, lire l'un des codes suivants

pour sélectionner la nationalité du clavier.

DFür den Betrieb mit einer Wedge-Schnittstelle lesen Sie

einen der folgenden Codes, um die Tastaturnationalität

einzustellen.

English

i'+k

Deutsch

i'+k

Svenskt

i'+k

Français

i'+gk

Italiano

i'+bk

USA

i'+]k

Español

i'+k

Belge

i'+k

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Datalogic Lettore di codici a barre

Datalogic

Datalogic Gryphon I GM4100-BK Manuale utente

Datalogic

Datalogic MAGELLAN 8400 Manuale utente

Datalogic

Datalogic GRYPHON Manuale utente

Datalogic

Datalogic Gryphon GFS41XX Manuale utente

Datalogic

Datalogic CBX800 Manuale utente

Datalogic

Datalogic DS8100 Manuale utente

Datalogic

Datalogic Magellan 8500Xt Manuale di installazione e funzionamento

Datalogic

Datalogic GRYPHON M SERIES Manuale utente

Datalogic

Datalogic PM9300 Manuale utente

Datalogic

Datalogic HandScanner SR Manuale utente

Datalogic

Datalogic MAGELLAN 1400I Manuale utente

Datalogic

Datalogic RIDA DBT6400 Manuale di servizio

Datalogic

Datalogic Touch TD1100 Family Manuale utente

Datalogic

Datalogic QuickScan L QD 2300 Manuale di installazione e funzionamento

Datalogic

Datalogic DV9500 Series Manuale utente

Datalogic

Datalogic PowerScan PM8300 Manuale di installazione e funzionamento

Datalogic

Datalogic DX8200A Manuale utente

Datalogic

Datalogic POWERSCAN 7000 2D Imager Manuale di installazione e funzionamento

Datalogic

Datalogic Matrix 120 Manuale di installazione e funzionamento

Datalogic

Datalogic Gryphon D100 Manuale utente

Datalogic

Datalogic Heron D130 Manuale utente

Datalogic

Datalogic Gryphon D432 Manuale utente

Datalogic

Datalogic Dragon D131 Manuale utente

Datalogic

Datalogic GRYPHON BT100 Manuale utente

Manuali Lettore di codici a barre popolari di altre marche

POSMicro

POSMicro Datalogic PowerScan D7100 Manuale utente

Marson

Marson MT780 Guida rapida alla configurazione

NCR

NCR RealPOS Manuale utente

Motorola

Motorola SE3300 Guida rapida alla configurazione

Element

Element P130BT Manuale utente

Motorola

Motorola Symbol LS3008 Manuale di installazione e funzionamento

Meec tools

Meec tools OBD-II / VAG Manuale utente

SICK

SICK CLP 100 Manuale utente

Royal Tag SA

Royal Tag SA I-Read Manuale utente

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manuale utente

Meteor

Meteor 8310 Manuale utente

Denso

Denso BHT-500B Manuale utente

Motorola

Motorola MP6000 Istruzioni di montaggio

Newland

Newland NLS-HR15-BT Manuale utente

ARTDEV

ARTDEV AS-1310 Manuale utente

Aopos

Aopos AS290 Manuale utente

ENS

ENS 367-5455 Manuale utente

Atid

Atid AT188N Plus Manuale utente