Dell PowerEdge M420 Manuale utente

Dell and the Dell logo are

trademarks of Dell Inc.

Dell 10GbE Pass Through Module (XAUI)

User Manual

P/N: M1601P

Rev 1.0

16 Port Pass Through Module

Document Number: 3192

Rev 1.0

____________________

Information in this document is subject to change without notice.

Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text: Dell™, the DELL logo, and PowerEdge™ are trademarks of Dell Inc.;

Other trademarks and trade names may be used in this document to refer to either the entities claiming the mark and names or their

products. Dell Inc. disclaims any proprietary interest in trademarks and trade names other than its own.

July 2010 Rev: A00

Dell -10GbE PTM Rev 1.0

Table of Contents

Intended Audience 5

Conventions 5

Chapter 1 Overview 6

1.1 Features 6

1.2 Serial Number and Product Version Information 7

Chapter 2 Installation and Basic Operation 8

2.1 Unpacking the Pass Through Module 8

2.2 Insertion and Removal of the PTM 8

2.2.1 PTM Insertion 8

2.2.2 PTM Removal 9

2.3 Connecting the External Ports 9

2.3.1 10 Gigabit Ethernet SFP+ Modules 9

2.3.2 Installation and Removal of Optical Transceiver Modules 9

2.4 LED Indicators 10

2.4.1 System LEDs 10

2.4.2 Port LEDs 10

2.4.3 Installation Safety Warnings 12

2.4.4 Mechanical Installation 13

2.4.5 Cable Installation 13

Chapter 3 Troubleshooting 14

Appendix A Specifications 15

A.1 Mechanical Drawing with Dimensions 16

Appendix B Supported Optical Modules and DCAs 17

Appendix C EMC Certification Statements 18

C.1 FCC Statements (USA) 18

C.2 ICES Statements (Canada) 19

C.3 VCCI Statements (Japan) 19

C.4 KCC Certification (Korea) 19

Appendix D Interface Connector Pinouts 21

D.1 SFP+ Interface 21

Rev 1.0

Related Documentation

The documentation set accompanying the Pass Through Module includes the following:

Table 1 - Reference Documents and Web Sites

Firmware and Firmware Update Tools

Dell Pass Through Module Software User Manual

Latest Supported Cables and Optical Modules

Dell -10GbE PTM Rev 1.0

About this Manual

This User Manual is for the Dell 10Gb Ethernet Pass Through II passs through module.

This manual describes the installation and basic use of Dell 10GbE 16 port Pass Through Module

for blade servers.

Intended Audience

This manual is intended for users and system administrators responsible for installing and setting

up the Dell 10GbE 16 port Pass Through Module for blade servers.

Conventions

The terms downlink (internal–from servers) and uplink (external–out to the world) are used

throughout the document. Downlink refers to server connections through the backplane where

Ethernet is used. Uplink refers to the outside network, where a different Ethernet protocol is used.

The term PTM is used to indicate the Dell 10GbE 16 port Pass Through Module.

Caution: This symbol indicates the possibility of physical injury to the user or

installer.

OverviewRev 1.0

1 Overview

The PTM is an I/O module designed for the PowerEdge M1000e Dell Chassis. The product pro-

vides 10Gigabit connectivity for blade servers to Ethernet LANs. The product supports the follow-

ing Ethernet protocols.

Each front panel port provides connectivity to the blade with the corresponding number in the

chassis.

Figure 1: Pass Through II Front Panel

1.1 Features

The PTM feature set includes:

Internal Links

• 16 links of 10Gb Ethernet through the backplane

External links

• 16 SFP+ front panel ports of 10Gb Ethernet

IEEE and Other Ethernet Standards Compliance

• IEEE 802.3ae 10Gigabit Ethernet support

• IEEE 802.3ap Ethernet Operation over Electrical Backplanes

• Jumbo Frames up to 9K support

Connectors and Cabling

• Twin Axial Pair connector

• Optical modules for SR and LR

• All ports support active cables

Front Panel Indicators

• Per port status LEDs: Link Up, Link Activity

Table 2 - Protocols

Physical Connections Pass Through II Protocol

Blade Servers to PTM (Internal

Links)

XAUI

Front Panel Ports (External Links) 10G XFI

D10 Gb Ethernet Pass Through II

Dell -10GbE PTM Rev 1.0

• System status LEDs: Power Supply, Status

1.2 Serial Number and Product Version Information

The serial number and product version information are found on the label seen in the figure below.

Figure 2: Generic Product label

S/N: IL0HCC2D215463325875

P/N: 0HCC2D

Rev: X1

Installation and Basic OperationRev 1.0

2Installation and Basic Operation

2.1 Unpacking the Pass Through Module

Before you install your new PTM, unpack it and make sure that there is no visible damage that

may have occurred during shipping. Your package should contain the following items:

• Dell -10GbE Pass Through Module for Blade Servers

• This User’s Manual

The PTM is shipped without optical modules.

If anything in the package is damaged or missing, please contact your customer representative

immediately.

2.2 Insertion and Removal of the PTM

The Dell 10Gb Ethernet Pass Through II may be plugged into fabric slots B1, B2, C1, and C2.

Determine which slot to use, based on desired system configuration.

2.2.1 PTM Insertion

Insert the PTM into the chassis as shown in the following diagram:

Figure 3: Dell Chassis Slots for the PTM

Slot B1 Slot C1 Slot B2Slot C2

Dell -10GbE PTM Rev 1.0

The PTM supports hot-insertion into the chassis. If the PTM is inserted to a powered chassis, the

power LED (green) should turn on immediately.

2.2.2 PTM Removal

The PTM supports hot-removal. It may be removed when the chassis is powered on or off.

The PTM must not be removed during a firmware update process.

Note: Firmware update is in progress when the amber LED is blinking.

2.3 Connecting the External Ports

The PTM front panel presents 16 SFP+ ports. Each port provides connectivity to a server with the

respective number. Figure 4 shows the front panel view of the PTM.

Figure 4: Pass Through II Front Panel

2.3.1 10 Gigabit Ethernet SFP+ Modules

The PTM supports SFP+ modules for 10 Gigabit Ethernet, with 10GBASE-SR and 10GBASE-LR

PHYs. SFP+ modules must be approved for use with this PTM. Modules not approved may not

work. See Supported Optical Modules and DCAs on page 17 for lists of approved DCAs and opti-

cal modules.

2.3.2 Installation and Removal of Optical Transceiver Modules

Optical transceiver modules have a locking mechanism which can be opened or closed.

To insert the module into the cage:

1. Open the module’s locking mechanism.

2. Make sure that the male connectors on the module aligns with the female connector inside of

the cage. Also check that there is no dirt or foreign matter in the module or in the cage.

3. Insert the module into the adapter card module cage.

4. Close the locking Mechanism.

To remove the module from the cage:

1. Unlock the locking mechanism by opening the handle.

2. Pull the module out of the cage.

D10 Gb Ethernet Pass Through II

Installation and Basic OperationRev 1.0

2.4 LED Indicators

2.4.1 System LEDs

The system status LEDs indicate whether the PTM is receiving power from the chassis, and the

state of the PTM.

There are two system LEDs on the end of the module. The LED indications and meanings are

explained in the figure and table below.

Figure 5: Indicator LEDs

Table 3 - PTM states and LED configurations:

2.4.2 Port LEDs

The PTM has two I/O LEDs per port. The I/O LEDs are located on the I/O panel. The green LED,

when lit, indicates that the driver is running and a valid physical connection between nodes exists.

If the green LED is blinking, it indicates a problem with the physical link. The yellow LED when

lit, indicates a valid data activity link, this is the logical link. The yellow LED illuminates when the

network is discovered over the physical link. A valid data activity link without data transfer is des-

LED Module Status

Indication Status Power

OFF OFF OFF

OFF ON Boot in Progress

PTM not ready

Blinking Blue

BLINKING BLUE ON The CMC is identifying

the newly installed PTM

ON BLUE ON PTM is on and operating Normally

ON or BLINKING

AMBER

ON FW update is in progress or

Fault in System

Self-diagnosed

ON or BLINKING

AMBER

OFF Fault in System

CMC-detected

The IO Module is on and

ready when this LED is

green.

This LED can be blue or

amber. A fault is indicated

when the amber LED is blink-

ing. See Table 3.

Altri manuali per PowerEdge M420

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Dell Unità di controllo

Dell

Dell PowerConnect W Series Istruzioni operative e di manutenzione

Dell

Dell LC-EJ-10GE-10P Manuale utente

Dell

Dell UPS 2700R Series Manuale utente

Dell

Dell H955N Manuale utente

Dell

Dell MXG610s Manuale utente

Dell

Dell PowerConnect W-6000M3 Manuale utente

Dell

Dell PowerEdge M420 Manuale di servizio

Dell

Dell K804N Manuale utente

Dell

Dell PowerEdge FN Manuale utente

Dell

Dell FC SAN Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente