Dell P2422HEb Manuale utente

Manuali Monitor popolari di altre marche

Linear Acoustic

Linear Acoustic LQ-1000 Manuale utente

AOC

AOC I2579V Manuale utente

Gateway

Gateway FPD1520 Manuale utente

Furuno

Furuno Mu 120c Manuale utente

Asus

Asus VB171D - 17" LCD Monitor Manuale utente

Philips

Philips 107C64 Manuale utente

EverFocus

EverFocus EN-7517E Manuale utente

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manuale utente

LG

LG 50PM1M - - 50" Plasma Panel Manuale utente

Bosch

Bosch DDU 9 Manuale utente

Acer

Acer A231HL Manuale utente

Philips

Philips 86BDL4152T Manuale utente

NEC

NEC AccuSync LCD5V Manuale utente

Emay

Emay SleepO2 Manuale utente

IBM

IBM 6360 Istruzioni per l'installazione

LG

LG M1950D-PZ Manuale utente

Sceptre

Sceptre D40 Manuale utente

Hunt Electronic

Hunt Electronic HCD-15AH Manuale utente

1

D

ELL

P

2

4

22H

E

B

1. Disassembly Procedures

S1

Turn off the monitor.

S2

To remove the stand:

Place the monitor on a soft cloth or

cushion

Press and hold the stand release button

Lift the stand up and away from the

monitor

S3

Unlock 4 RC screws

isassemble Rear Cover from Middle

Frame according to the sequence

shown in the picture

(Screw Torque: 9±1kgf)

S4

Pull out CTRL FFC from I/F B to take

off Rear Cover

S5

Tear off 1 tape from CTRL B FFC on

Rear Cover

Unlock 3 screws to disassemble CTRL

B from Rear Cover

(Screw Torque: 1.4±0.1kgf)

S6

Tear off malar from Main SH

Pull out USB FFC from USB B and I/F

B

2

D

ELL

P2

4

22H

E

B

S7

Unlock 1 screw on USB B

isassemble USB B from Middle

Frame

(Screw Torque: 4.5±0.5kgf)

S8

Tear off adhesive tape on Backlight

Wire

Pull out Backlight Wire from LE river

B

isassemble Main SH from Middle

Frame

S9

Pull out LV S cable and take off Main

SH from panel

S1

Unlock 9 screws on Middle Frame

Unlock 2 screws on Bezel Chin

(Screw Torque-MF: 3.5~~4.0kgf)

(Screw Torque-BZL Chin: 2.0±0.1kgf)

S11

isassemble Middle Frame and Bezel

Chin from Panel

S12

Pull out Backlight Wire from panel

3

D

ELL

P

2

4

22H

E

B

S13

isassemble Mylar from Main SH

S14

Unlock 8 PCB screws

(Screw Torque-PCB: 8.5±1kgf)

S15

isassemble I/F B , SPS B , LE

river B from Main SH

Pull out all cables from I/F B , SPS B

and LE river B

4

D

ELL

P2

4

22H

E

B

S16

Remove electrolyte capacitors (red mark) from printed circuit boards

S16-1 Cut the glue between bulk cap. and PCB with a knife

S16-2 Ensure cutting path within the glue, don’t touch bulk cap. or PCB

5

D

ELL

P

2

4

22H

E

B

S16-3 Take out bulk cap. pin solder with soldering iron and absorber

S16-4 Lift the bulk cap. up and away from the PCB

6

D

ELL

P2

4

22H

E

B

2. Product material information

The following substances, preparations, or components should be disposed of or

recovered separately from other WEEE in compliance with Article 4 of EU Council

Directive 75/442/EEC.

Capacitors / condensers (containing

PCB/PCT)

No used

Mercury containing components

No used

Batteries No used

Printed circuit boards (with a surface greater

than 10 square cm)

Product has printed circuit boards

(with a surface greater than 10 square

cm)

Component contain toner, ink and liquids No used

Plastic containing BFR

No used

Component and waste contain asbestos

No used

CRT No used

Component contain CFC, HCFC, HFC and

HC

No used

Gas discharge lamps

No used

LCD display > 100 cm2 Product has an LCD greater than 100

cm2

External electric cable Product has external cables

Component contain refractory ceramic fibers

No used

Component contain radio

-

active substances

No used

Electrolyte capacitors (height

> 25mm, diameter > 25mm)

Product has electrolyte capacitors

(height >25mm, diameter > 25mm)

3. Tools Required

List the type and size of the tools that would typically can be used to disassemble the

product to a point where components and materials requiring selective treatment can be

removed.

Tool Description:

- Screwdriver

- Scraper Bar

- Penknife

- Soldering iron and absorber