Dell S2421HS Manuale utente

Wedge your fingers between the rear cover and the

middle bezel on the corners of the top side of the

monitor to release the rear cover, then use one hand

to press the middle bezel, the other hand to pull up

carefully the rear cover in order of arrow preference

for unlocking mechanisms of rear cover..

Use a Philips-head screwdriver to remove 4pcs

screws for unlocking mechanisms.

(No.1~4 screw size=M4x11; Torque=7 8kgfxcm)~

Take out all of the QSG,accessories including HDMI

cable, power cable, CD&user’s manual, stand base,

stand riser and EEI label from the carton. (Note: It

depends on whether users returning the accessories)

Open the Pizza carton with a proper tool.

1. Disassembly Procedures:

Take out of the from the

carton, then take out the riser and monitor from the

EPE bag and put it on a protective cushion.

molded pulp with base

1S2421HS/HSX

riser

base

QSG

user’s manual

HDMI cable

power cable

label and paper

monitor

Tear off 2pcs aluminum foils, and then disconnect

the function key cable away from the connector of

the board. Disconnect the panel lamp cable and

function key cable away from the connectors of the

panel module and board.

S2421HS/HSX

S11

Use a Philips-head screwdriver to remove 2pcs

screws for unlocking the bracket chassis with panel

module.

(No.1~2 screw size=M3x3, Torque=3~4kgfxcm )

S10

Unplug the LVDS cable from the connector of the

panel module by pushing the earing-locks.

Use a Philips-head screwdriver to remove 16pcs

screws for unlocking the middle bezel.

(No.1~11 screw size=M3x4, Torque=3~4kgfxcm;

No.12~16 screw size=M2x3.3, Torque=1±0.2kgfxcm)

1 3

Lift up the middle bezel and take away the middle

bezel, and put it on a fixture. U

tear off the tapes for releasing the key cables.

se a Philips-head

screwdriver to remove 3pcs screws for unlocking the

function key board with the middle bezel, and then

(No.1~3 screw size=M2x2.4, Torque=0.8±0.2kgfxcm

tear off the tape.

ift up the panel module with the bracket chassis for

releasing the front bezel away from the panel

module, and then

Take away the bracket chassis module and then put

the bracket chassis module on a protective cushion.

Remove the interface board and power board from

the bracket chassis module carefully, and disconnect

all the cables.

Use a Philips-head screwdriver to remove 5pcs

screws for unlocking the circuit board, release all the

cables from the hooks.

(No.1 screw size=M4x8, Torque=6±0.5kgfxcm;

No. 2~5 screw size=M3x7.5, Torque=6±0.5kgfxcm)

S14

S15

Remove the Mylar from the hooks of the bracket

chassis module.

S13

S12

3S2421HS/HSX

S2421HS/HSX

Remove electrolyte capacitors (red mark) from

printed circuit boards.

S16

S16-1 Cut the glue between bulk cap. and PCB with a knife.

S16-2 Ensure cutting path within the glue, don’t touch bulk

cap. or PCB.

S16-4 Take out bulk cap. pin solder with soldering iron and

absorber.

S16-5 Lift the bulk cap. up and away from the PCB.

S16-3 Cut into the bottom of bulk cap. and pullit up

carefully.

5S2421HS/HSX

The following substances, preparations, or components should be disposed of or

recovered separately from other WEEE in compliance with Article 4 of EU Council

Directive 75/442/EEC.

Capacitors / condensers (containing

PCB/PCT)

No used

Mercury containing components

No used

Batteries

No used

Printed circuit boards (with a surface

greater than 10 square cm)

Product has printed circuit boards (with a

surface greater than 10 square cm)

Component contain toner, ink and

liquids

No used

Plastic containing BFR

No used

Component and waste contain

asbestos

No used

CRT

No used

Component contain CFC, HCFC, HFC

and HC

No used

Gas discharge lamps

No used

LCD display > 100 cm2

Product has an LCD greater than 100 cm2

External electric cable

Product has external cables

Component contain refractory

ceramic fibers

No used

Component contain radio-active

substances

No used

Electrolyte capacitors (height

> 25mm, diameter > 25mm)

Product has electrolyte capacitors (height >

25mm, diameter > 25mm)

3. Tools Required

List the type and size of the tools that would typically can be used to disassemble the

product to a point where components and materials requiring selective treatment

can be removed.

Tool Description:

- Screwdriver (Phillip head) #1

- Screwdriver (Phillip head) #2

- Penknife

- Soldering iron and absorber

2. Product material information

Altri manuali per S2421HS

Questo manuale è adatto per i seguenti modelli

Altri manuali Dell Monitor

Manuali Monitor popolari di altre marche

Linear Acoustic

Linear Acoustic LQ-1000 Manuale utente

AOC

AOC I2579V Manuale utente

Gateway

Gateway FPD1520 Manuale utente

Furuno

Furuno Mu 120c Manuale utente

Asus

Asus VB171D - 17" LCD Monitor Manuale utente

Philips

Philips 107C64 Manuale utente

EverFocus

EverFocus EN-7517E Manuale utente

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manuale utente

LG 50PM1M - - 50" Plasma Panel Manuale utente

Bosch

Bosch DDU 9 Manuale utente

Acer

Acer A231HL Manuale utente

Philips

Philips 86BDL4152T Manuale utente

NEC

NEC AccuSync LCD5V Manuale utente

Emay

Emay SleepO2 Manuale utente

IBM

IBM 6360 Istruzioni per l'installazione

LG M1950D-PZ Manuale utente

Sceptre

Sceptre D40 Manuale utente

Hunt Electronic

Hunt Electronic HCD-15AH Manuale utente