DELTA DORE Tywatt EM.IC Manuale utente
EM.IC
EN
Consumption information transmitter
for double-service heat pump
2 3
EN
1 - Installation
Install the EM.IC around 1.50 m off the ground.
2 - Mounting - connection
- Switch off the installation power supply
- Install the device around 1.50 m off the ground
to enhance radio propagation.
- Connect the power supply to terminals 1 and 2.
- To select the cabling suitable for your installation,
consult the specications contained
in the assembly instructions or in the specications
provided by the manufacturer of your heat pump
You can nd installation diagrams adapted
to your heat pump on the EM.IC page of
the www.deltadore.com site
1,50 m
Heat pump
20 cm 1
4
5
230V~
50 Hz
OFF
2
3
7
230V~
50 Hz
ON
6
!
1 2 3
L
L
N
230V
~
50 Hz
...
4 5
EN
3 - Pairing with an RT2012 system manager
4 - Pairing with the Tydom app
Your installation is equipped with a Tywatt
5400/5450, which is already paired with the
Tydom application - pair the EM.IC with the Tydom
application.
From the Tydom application, select
Settings > My home > My devices > Add a device >
Consumption > then select your previously paired
Tywatt with which you wish to pair the EM.IC and
follow the on-screen instructions.
OK
1
5
>3s
2 43
... ... ... .. .. ..... .. ..
6
OFF
OK
5 6
>3s
21 43
OFF
... ... ... .. .. ..... .. ..
Set the
system manager
to pending pairing.
Read the instructions
- Hold down the button for 3 seconds
until the LED ashes, then release.
- Briey press the button, the LED will ash quickly.
- Hold down the button for 3 seconds
until the LED ashes, then release.
- Briey press the button, the LED will ash quickly.
Check on
the system ma-
nager
that the pairing
was successful
Check that the LED on the EM.IC
is no longer ashing.
The products are now paired.
6 7
EN
5 - Reset to factory settings
❶Hold down the receiver button for 10 seconds:
- after 3 seconds, the LED ashes slowly.
- after 7 seconds, the LED ashes quickly.
- press and hold the button until the LED goes
out.
❷Release.
All paired devices are now deleted.
RESET OK
12
>10s
3s 7s
... ... ...
OFF
.. .. ..... .. ..
Technical specications
- Power supply: 230 V~, 50 Hz,
- Consumption : 1 VA
- Class II insulation
- Type 1 action
- Rated impulse withstand voltage: 2500 V
- Ball test temperature: 75°C
- Storage temperature: -10°C / +70°C
- Operating temperature: 0°C / +55°C
- IP 44 with the supplied cable.
Vertical positioning of the product
- Dimensions: 54 x 140 x 25 mm
- X3D wireless remote control device:
868.7 MHz to 869.2 MHz
- Maximum wireless power < 10 mW
- Category 2 receiver
- Installation in an environment with normal pollution
levels
- Cable: 3 x 0.75 mm2(type H05VV-F)
Min. diameter: 6.5 mm.
Length: 1 m.
If the EM.IC is paired with the Tydom application,
begin by deleting the pairing via the Tydom
application.
03/23
www.deltadore.com
Indice
Altri manuali DELTA DORE Trasmettitore
DELTA DORE
DELTA DORE TYDOM 2.0 Manuale utente
DELTA DORE
DELTA DORE TYXIA 2330 Manuale utente
DELTA DORE
DELTA DORE TYXIA 2330 Manuale utente
DELTA DORE
DELTA DORE TYXIA 2330 Manuale utente
DELTA DORE
DELTA DORE TYXIA 2330 Manuale utente
DELTA DORE
DELTA DORE TYDOM 2.0 Manuale utente
DELTA DORE
DELTA DORE TYDOM 2.0 Manuale utente
DELTA DORE
DELTA DORE TYXIA 2330 Manuale utente
DELTA DORE
DELTA DORE TTRTC TYXAL+ Manuale utente
DELTA DORE
DELTA DORE TYBOX 5150 Manuale utente
