Delta Electronics AC Motor Drive VFD-EL Manuale utente

Preface

Thank you for choosing DELTA’s multifunction VFD-EL Series. The VFD-EL Series is manufactured

with high-quality components and materials and incorporate the latest microprocessor technology

available.

This manual is to be used for the installation, parameter setting, troubleshooting, and daily

maintenance of the AC motor drive. To guarantee safe operation of the equipment, read the following

safety guidelines before connecting power to the AC motor drive. Keep this operating manual at

hand and distribute to all users for reference.

To ensure the safety of operators and equipment, only qualified personnel familiar with AC motor

drive are to do installation, start-up and maintenance. Always read this manual thoroughly before

using VFD-EL series AC Motor Drive, especially the WARNING, DANGER and CAUTION notes.

Failure to comply may result in personal injury and equipment damage. If you have any questions,

please contact your dealer.

PLEASE READ PRIOR TO INSTALLATION FOR SAFETY.

DANGER!

1. AC input power must be disconnected before any wiring to the AC motor drive is made.

2. A charge may still remain in the DC-link capacitors with hazardous voltages, even if the power

has been turned off. To prevent personal injury, please ensure that power has turned off before

opening the AC motor drive and wait ten minutes for the capacitors to discharge to safe voltage

levels.

3. Never reassemble internal components or wiring.

4. The AC motor drive may be destroyed beyond repair if incorrect cables are connected to the

input/output terminals. Never connect the AC motor drive output terminals U/T1, V/T2, and

W/T3 directly to the AC mains circuit power supply.

5. Ground the VFD-EL using the ground terminal. The grounding method must comply with the

laws of the country where the AC motor drive is to be installed. Refer to the Basic Wiring

Diagram.

6. VFD-EL series is used only to control variable speed of 3-phase induction motors, NOT for 1-

phase motors or other purpose.

7. VFD-EL series shall NOT be used for life support equipment or any life safety situation.

WARNING!

1. DO NOT use Hi-pot test for internal components. The semi-conductor used in AC motor drive

easily damage by high-voltage.

2. There are highly sensitive MOS components on the printed circuit boards. These components

are especially sensitive to static electricity. To prevent damage to these components, do not

touch these components or the circuit boards with metal objects or your bare hands.

3. Only qualified persons are allowed to install, wire and maintain AC motor drives.

CAUTION!

1. DO NOT install the AC motor drive in a place subjected to high temperature, direct sunlight,

high humidity, excessive vibration, corrosive gases or liquids, or airborne dust or metallic

particles.

2. Some parameters settings can cause the motor to run immediately after applying power

3. Only use AC motor drives within specification. Failure to comply may result in fire, explosion or

electric shock.

4. To prevent personal injury, please keep children and unqualified people away from the

equipment.

5. When the motor cable between AC motor drive and motor is too long, the layer insulation of the

motor may be damaged. Please use a frequency inverter duty motor or add an AC output

reactor to prevent damage to the motor. Refer to appendix B Reactor for details.

6. The rated voltage for AC motor drive must be ≤240V (≤480V for 460V models) and the mains

supply current capacity must be ≤5000A RMS.

Table of Contents

Preface ............................................................................................................. i

Table of Contents .......................................................................................... iii

Chapter 1 Introduction ................................................................................ 1-1

1.1 Receiving and Inspection....................................................................1-2

1.1.1 Nameplate Information................................................................ 1-2

1.1.2 Model Explanation ...................................................................... 1-2

1.1.3 Series Number Explanation ........................................................ 1-3

1.1.4 Drive Frames and Appearances ................................................. 1-3

1.1.5 Remove Instructions ................................................................... 1-5

1.2 Preparation for Installation and Wiring................................................1-5

1.2.1 Ambient Conditions..................................................................... 1-6

1.2.2 DC-bus Sharing: Connecting the DC-bus of the AC Motor Drives in

Parallel................................................................................................. 1-8

1.3 Dimensions.........................................................................................1-9

Chapter 2 Installation and Wiring ..............................................................2-1

2.1 Wiring .................................................................................................2-2

2.2 External Wiring ...................................................................................2-8

2.3 Main Circuit.........................................................................................2-9

2.3.1 Main Circuit Connection.............................................................. 2-9

2.3.2 Main Circuit Terminals .............................................................. 2-11

2.4 Control Terminals .............................................................................2-12

Chapter 3 Keypad and Start Up ..................................................................3-1

3.1 Description of the Digital Keypad ....................................................... 3-1

3.2 How to Operate the Digital Keypad .................................................... 3-3

3.3 Reference Table for the 7-segment LED Display of the Digital Keypad3-

3.4 Operation Method .............................................................................. 3-4

3.5 Trial Run ............................................................................................ 3-5

Chapter 4 Parameters..................................................................................4-1

4.1 Summary of Parameter Settings ........................................................ 4-2

4.2 Parameter Settings for Applications ................................................. 4-21

4.3 Description of Parameter Settings.................................................... 4-26

Chapter 5 Troubleshooting .........................................................................5-1

5.1 Over Current (OC).............................................................................. 5-1

5.2 Ground Fault ...................................................................................... 5-2

5.3 Over Voltage (OV).............................................................................. 5-2

5.4 Low Voltage (Lv) ................................................................................ 5-3

5.5 Over Heat (OH1) ................................................................................ 5-4

5.6 Overload ............................................................................................ 5-4

5.7 Keypad Display is Abnormal .............................................................. 5-5

5.8 Phase Loss (PHL) .............................................................................. 5-5

5.9 Motor cannot Run............................................................................... 5-6

5.10 Motor Speed cannot be Changed .................................................... 5-7

5.11 Motor Stalls during Acceleration....................................................... 5-8

5.12 The Motor does not Run as Expected.............................................. 5-8

5.13 Electromagnetic/Induction Noise...................................................... 5-9

5.14 Environmental Condition...................................................................5-9

5.15 Affecting Other Machines ...............................................................5-10

Chapter 6 Fault Code Information and Maintenance................................ 6-1

6.1 Fault Code Information .......................................................................6-1

6.1.1 Common Problems and Solutions............................................... 6-1

6.1.2 Reset .......................................................................................... 6-5

6.2 Maintenance and Inspections .............................................................6-5

Appendix A Specifications ........................................................................ A-1

Appendix B Accessories ........................................................................... B-1

B.1 All Brake Resistors & Brake Units Used in AC Motor Drives............. B-1

B.1.1 Dimensions and Weights for Brake Resistors ............................ B-4

B.2 No Fuse Circuit Breaker Chart .......................................................... B-7

B.3 Fuse Specification Chart ................................................................... B-8

B.4 AC Reactor........................................................................................ B-9

B.4.1 AC Input Reactor Recommended Value.....................................B-9

B.4.2 AC Output Reactor Recommended Value..................................B-9

B.4.3 Applications ..............................................................................B-10

B.5 Zero Phase Reactor (RF220X00A) ................................................. B-12

B.6 Remote Controller RC-01................................................................ B-13

B.7 PU06 ............................................................................................... B-14

B.7.1 Description of the Digital Keypad VFD-PU06 ........................... B-14

B.7.2 Explanation of Display Message...............................................B-14

B.7.3 Operation Flow Chart ............................................................... B-15

B.8 Fieldbus Modules ............................................................................ B-16

B.8.1 DeviceNet Communication Module (CME-DN01) .....................B-16

B.8.1.1 Panel Appearance and Dimensions ..................................B-16

B.8.1.2 Wiring and Settings ...........................................................B-16

B.8.1.3 Power Supply ....................................................................B-17

B.8.1.4 LEDs Display.....................................................................B-17

B.8.2 LonWorks Communication Module (CME-LW01) .....................B-17

B.8.2.1 Introduction .......................................................................B-17

B.8.2.2 Dimensions .......................................................................B-17

B.8.2.3 Specifications ....................................................................B-18

B.8.2.4 Wiring................................................................................B-18

B.8.2.5 LED Indications .................................................................B-18

B.8.3 Profibus Communication Module (CME-PD01).........................B-19

B.8.3.1 Panel Appearance.............................................................B-19

B.8.3.2 Dimensions .......................................................................B-20

B.8.3.3 Parameters Settings in VFD-EL ........................................B-20

B.8.3.4 Power Supply ....................................................................B-20

B.8.3.5 PROFIBUS Address..........................................................B-20

B.8.4 CME-COP01 (CANopen) ..........................................................B-21

B.8.4.1 Product Profile...................................................................B-21

B.8.4.2 Specifications ....................................................................B-21

B.8.4.3 Components......................................................................B-22

B.8.4.4 LED Indicator Explanation & Troubleshooting...................B-23

B.9 MKE-EP & DIN Rail ......................................................................... B-25

B.9.1 MKE-EP ....................................................................................B-25

B.9.2 DIN Rail: MKEL-DRA (Only for frame A)...................................B-26

Appendix C How to Select the Right AC Motor Drive.............................. C-1

C.1 Capacity Formulas ............................................................................ C-2

C.2 General Precaution ........................................................................... C-4

C.3 How to Choose a Suitable Motor....................................................... C-5

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Delta Electronics Controllori

Delta Electronics

Delta Electronics ASDA-A2 Series Manuale utente

Delta Electronics

Delta Electronics Climate Control Unit CCU Manuale utente

Delta Electronics

Delta Electronics DVP-ES2 Series Manuale utente

Delta Electronics

Delta Electronics Programmable Logic Controller DVP-SS Manuale utente

Delta Electronics

Delta Electronics Programmable Logic Controller DVP-PLC Manuale utente

Delta Electronics

Delta Electronics Position Control Module DVP01PU-H Manuale utente

Delta Electronics

Delta Electronics Program Copy Card TP-PCC Manuale utente

Delta Electronics

Delta Electronics DVP-SS2 Manuale utente

Delta Electronics

Delta Electronics Temperature Controller DTE Manuale utente

Delta Electronics

Delta Electronics AH500 Manuale utente

Delta Electronics

Delta Electronics DVP-EH2 Manuale utente

Delta Electronics

Delta Electronics AH500 Manuale utente

Delta Electronics

Delta Electronics Program Copy Card TP-PCC01 Manuale utente

Delta Electronics

Delta Electronics Programmable Logic Controller DVP-SC Manuale utente

Delta Electronics

Delta Electronics Programmable Logic Controller DVP06XA-H2 Manuale utente

Delta Electronics

Delta Electronics DVP15MC11T Manuale utente

Delta Electronics

Delta Electronics Programmable Logic Controller DVP-SA Manuale utente

Delta Electronics

Delta Electronics Programmable Logic Controller DVP-EH2-L Manuale utente

Delta Electronics

Delta Electronics Valve Temperature Controller DTV Manuale utente

Delta Electronics

Delta Electronics Programmable Logic Controller DVP04DA-H2 Manuale utente

Delta Electronics

Delta Electronics DVP-MC Series Manuale utente

Delta Electronics

Delta Electronics Programmable Logic Controller DVP28SV Manuale utente

Delta Electronics

Delta Electronics DTC1000 Series Manuale utente

Delta Electronics

Delta Electronics AC Motor Drive VFD-VE Series Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente