DFI EC900-FS6 Manuale utente
1
Chapter 1 Introduction
EC900-FS6
Fanless Embedded System
User’s Manual
A48300809
2
Chapter 1 Introduction
Copyright
This publication contains information that is protected by copyright. No part of it may be re-
produced in any form or by any means or used to make any transformation/adaptation without
the prior written permission from the copyright holders.
This publication is provided for informational purposes only. The manufacturer makes no
representations or warranties with respect to the contents or use of this manual and specifi-
cally disclaims any express or implied warranties of merchantability or fitness for any particular
purpose. The user will assume the entire risk of the use or the results of the use of this docu-
ment. Further, the manufacturer reserves the right to revise this publication and make changes
to its contents at any time, without obligation to notify any person or entity of such revisions
or changes.
Changes after the publication’s first release will be based on the product’s revision. The website
will always provide the most updated information.
© 2018. All Rights Reserved.
Trademarks
Product names or trademarks appearing in this manual are for identification purpose only and
are the properties of the respective owners.
FCC and DOC Statement on Class A
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reason-
able protection against harmful interference when the equipment is operated in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encour-
aged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio TV technician for help.
Notice:
1. The changes or modifications not expressly approved by the party responsible for compli-
ance could void the user’s authority to operate the equipment.
2. Shielded interface cables must be used in order to comply with the emission limits.
3
Chapter 1 Introduction
Table of Contents
About this Manual.................................... 4
Warranty ................................................. 4
Static Electricity Precautions ..................... 4
Safety Measures....................................... 4
Safety Precautions ................................... 5
About the Package................................... 5
Before Using the System .......................... 5
Chapter 1 - Introduction........................... 6
Overview.................................................................................6
Key Features ...........................................................................6
Specifications...........................................................................7
Getting to Know the EC900-FS6 ...............................................8
Mechanical Dimensions ............................................................9
Chapter 2 - Getting Started ...................... 10
Chapter 3 - Installing Devices................... 11
Removing the Chassis Cover................................................... 11
Chapter 4 - Jumper Settings..................... 13
Boot Mode Select................................................................... 13
Chapter 5 - Ports and Connectors............. 14
Panel I/O Ports...................................................................... 14
RJ45 LAN Ports ........................................................................ 15
9~36V DC-in .......................................................................... 15
USB Ports................................................................................ 16
Serial Port ............................................................................... 16
Graphics Interface.................................................................... 17
I/O Connectors ......................................................................17
Digital I/O Connector................................................................ 17
Serial Port ............................................................................... 18
Expansion Slots ....................................................................... 19
I2C Connector ......................................................................... 19
Front Panel Connector .............................................................. 20
Battery ................................................................................... 20
Debug Connectors ................................................................... 21
Chapter 6 - Mounting Options .................. 22
Chapter 7 - Supported Software ............... 23
4
Chapter 1 Introduction
About this Manual
An electronic file of this manual can be obtained from the DFI website at www.dfi.com. To
download the user’s manual from our website, please go to Support > Download Center. On
the Download Center page, select your product or type the model name and click "Search" to
nd all technical documents including the user's manual for a specic product.
Warranty
1. Warranty does not cover damages or failures that arised from misuse of the product,
inability to use the product, unauthorized replacement or alteration of components and
product specifications.
2. The warranty is void if the product has been subjected to physical abuse, improper instal-
lation, modification, accidents or unauthorized repair of the product.
3. Unless otherwise instructed in this user’s manual, the user may not, under any circum-
stances, attempt to perform service, adjustments or repairs on the product, whether in or
out of warranty. It must be returned to the purchase point, factory or authorized service
agency for all such work.
4. We will not be liable for any indirect, special, incidental or consequential damages to the
product that has been modified or altered.
Static Electricity Precautions
It is quite easy to inadvertently damage your PC, system board, components or devices even
before installing them in your system unit. Static electrical discharge can damage computer
components without causing any signs of physical damage. You must take extra care in han-
dling them to ensure against electrostatic build-up.
1. To prevent electrostatic build-up, leave the system board in its anti-static bag until you are
ready to install it.
2. Wear an antistatic wrist strap.
3. Do all preparation work on a static-free surface.
4. Hold the device only by its edges. Be careful not to touch any of the components, contacts
or connections.
5. Avoid touching the pins or contacts on all modules and connectors. Hold modules or con
nectors by their ends.
Safety Measures
To avoid damage to the system:
• Use the correct AC input voltage range.
To reduce the risk of electric shock:
• Unplug the power cord before removing the system chassis cover for installation or servic-
ing. After installation or servicing, cover the system chassis before plugging the power cord.
Battery:
• Danger of explosion if battery incorrectly replaced.
• Replace only with the same or equivalent type recommend by the manufacturer.
• Dispose of used batteries according to local ordinance.
Important:
Electrostatic discharge (ESD) can damage your processor, disk drive and other com-
ponents. Perform the upgrade instruction procedures described at an ESD worksta-
tion only. If such a station is not available, you can provide some ESD protection by
wearing an antistatic wrist strap and attaching it to a metal part of the system chas-
sis. If a wrist strap is unavailable, establish and maintain contact with the system
chassis throughout any procedures requiring ESD protection.
5
Chapter 1 Introduction
About the Package
The package contains the following items. If any of these items are missing or damaged,
please contact your dealer or sales representative for assistance.
• One EC900-FS6 system unit
• One Quick Installation Guide
Optional Items
• DIN-rail Mount kit
• Power Cord
The board and accessories in the package may not come similar to the information listed
above. This may differ in accordance to the sales region or models in which it was sold. For
more information about the standard package in your region, please contact your dealer or
sales representative.
Safety Precautions
• Use the correct DC input voltage range.
• Unplug the power cord before removing the system chassis cover for installation or servic-
ing. After installation or servicing, cover the system chassis before plugging the power cord.
• Danger of explosion if battery incorrectly replaced.
• Replace only with the same or equivalent type recommend by the manufacturer.
• Dispose of used batteries according to local ordinance.
• Keep this system away from humidity.
• Place the system on a stable surface. Dropping it or letting it fall may cause damage.
• The openings on the system are for air ventilation to protect the system from overheating.
DO NOT COVER THE OPENINGS.
• Place the power cord in such a way that it will not be stepped on. Do not place anything on
top of the power cord. Use a power cord that has been approved for use with the system
and that it matches the voltage and current marked on the system’s electrical range label.
• If the system will not be used for a long time, disconnect it from the power source to avoid
damage by transient overvoltage.
• If one of the following occurs, consult a service personnel:
- The power cord or plug is damaged.
- Liquid has penetrated the system.
- The system has been exposed to moisture.
- The system is not working properly.
- The system dropped or is damaged.
- The system has obvious signs of breakage.
• The unit uses a three-wire ground cable which is equipped with a third pin to ground the
unit and prevent electric shock. Do not defeat the purpose of this pin. If your outlet does
not support this kind of plug, contact your electrician to replace the outlet.
• Disconnect the system from the DC outlet before cleaning. Use a damp cloth. Do not use
liquid or spray detergents for cleaning.
6
Chapter 1 Introduction
Chapter 1 - Introduction
Chapter 1
Overview Key Features
Front View
Model Name EC900-FS6
Processor NXP i.MX6 Series Processor
NXP i.MX6 Cortex-A9 Dual Lite, 1.0GHz
LAN Two LAN ports
COM Two serial port:
2-wire RS485
4-wire RS422
Display One HDMI
USB Two USB 2.0 Type A ports
Digital input/output Terminal block for digital I/O with power
Left View
7
Chapter 1 Introduction
Specications
Chapter 1
Vibration • Operating: Random 5~500Hz, IEC68-2-64 (3G)
• Non-Operating: Sine 10~500Hz, IEC68-2-6 (3G)
Shock • Operating: 3G, 11ms
• Non-Operating: 5G, 11ms
Construction
• Sheet Metal
Mounting
• DIN-rail Mount
Dimensions • 145mm x 34mm x 96.4mm (W x H x D)
Weight • TBD
OS Support Yocto 1.8 beta, Kernel 3.14.52
Android 5.1 beta, Kernel 3.14.52
Processor
System
NXP i.MX6 Series Processor
NXP i.MX6 Cortex-A9 Dual Lite, 1.0GHz
Memory • 1GB/2GB SDRAM Memory Down
Single Channel DDR3L 1600MHz
Graphics • Display interface
HDMI: resolution up to 1920x1080 @ 60 Hz
Storage/
Expansion
• Storage
4MB NOR Flash
8GB/16GB eMMC
• Expansion:
1 x Full-size Mini PCIe (PCIe/USB)
1 x microSD
Ethernet • 1 x ATHEROS Ethernet Controller AR8033-AL1B (10/100/1000Mbps)
• 1 x Microchip's USB to Ethernet Controller LAN7500-ABZJ
(10/100/1000Mbps)
I/O Ports and
LED Indicators
• Front Panel
- 2 x RJ-45 LAN ports
- 1 x RS-485 (2-wire terminal block)
- 2 x USB 2.0 (type A)
- 1 x HDMI
- 1 status LED
- 1 reset button
• Side Panel
- 1 x RS-422 (4-wire terminal block)
- 1 x DIO (with power) connector (6-wire terminal block)
Power • 9~36V DC-in
Environment • Temperature
- Operating: -20oC ~ 60oC
-40oC ~ 70oC
- Storage: -40 to 85°C
• Relative Humidity
- 10% to 90% RH (non-condensing)
8
Chapter 1 Introduction
Status LED (blue)
This LED will blink when the system is in the standby mode.
Reset Button
Press to reset the system without disconnecting the system’s power.
USB 2.0 Ports
Connect USB 2.0 and 1.1 devices.
LAN Ports
Connect the system to a local area network.
RS485 Port
Connects RS485 devices.
HDMI Port
Connects the HDMI port of a display device.
Getting to Know the EC900-FS6
Chapter 1
Front View Rear View
DC-in Connector
DC 9~36V power input via a terminal block connector.
DIO Connector with Power
Provides 4-bit digital input/output with power connectivity (2-pin).
RS422 Port
Connects RS422 devices.
Status LED
(green) LAN 2 LAN 1
COM (RS485)
USB 2.0
HDMI
Reset
Status LED
Suspend Mode S0 Sleep S4, S5
LED Behavior On Blinking Off
Digital IO
(4-pin)
RS422 (4-pin)
DC-in
+
Power (1-pin)
Ground (1-pin)
9
Chapter 1 Introduction
Mechanical Dimensions
Chassis Dimension
Chapter 1
145
34 96.40
Left View
Right View
Front View
Bottom View Top View
10
Chapter 2 Getting Started
Chapter 2 - Getting Started
Chapter 2
Preparing the System
Before you start using the system, you need the following items:
• AC power cord
• Screwdriver
Installing Devices
The following devices can be installed in the system.
• Mini PCIe card
• micro SD
Configuring the BIOS
To get you started, you may need to change configurations such as the date, time and the
type of hard disk drive.
1. Power on the system.
2. After the memory test, the message “Press DEL to run setup” will appear on the screen.
Press the Delete key to enter the BIOS setup utility.
Installing the Operating System
The device platform is an embedded system with Yocto 1.8 beta or Android 5.1 beta pre-
loaded on the eMMC.
Altri manuali per EC900-FS6
1
Indice
Altri manuali DFI PC industriale
DFI
DFI DS912-OT Manuale utente
DFI
DFI KS-KH Series Manuale utente
DFI
DFI EC300 Series Manuale utente
DFI
DFI EC700-QRB Manuale utente
DFI
DFI EC102-XNX Manuale utente
DFI
DFI EC500-ADS Manuale utente
DFI
DFI DT200-CS Manuale utente
DFI
DFI ES220F-CS Manuale utente
DFI
DFI EC500-SD Manuale utente
DFI
DFI EC500-ADS Manuale utente
DFI
DFI EC511-SD Manuale utente
DFI
DFI EC700-BT Manuale utente
DFI
DFI EC700-BT Manuale utente
DFI
DFI VC230-BT Manuale utente
DFI
DFI EC900-FS6 Manuale utente
DFI
DFI EC500-HD Manuale utente
DFI
DFI EC310 Series Manuale utente
DFI
DFI DT200-CS Manuale utente
DFI
DFI DT122-HR Manuale utente
DFI
DFI ES220F-CS Manuale utente
