DFI CA64-EC Manuale utente

CA64-EC

Rev. A+

System Board Users Manual

Carte Mère Manuel Pour Utilisateur

System-Platine Benutzerhandbuch

Tablero Electrónico del Sistema Manual del Usuario

45100039

This publication contains information that is protected by copyright.

No part of it may be reproduced in any form or by any means or

used to make any transformation/adaptation without the prior

written permission from the copyright holders.

This publication is provided for informational purposes only. The

manufacturer makes no representations or warranties with respect to

the contents or use of this manual and specifically disclaims any

express or implied warranties of merchantability or fitness for any

particular purpose.The user will assume the entire risk of the use or

the results of the use of this document. Further, the manufacturer

reserves the right to revise this publication and make changes to its

contents at any time, without obligation to notify any person or

entity of such revisions or changes.

Trademarks

Microsoft®MS-DOS®, WindowsTM, Windows®95, Windows®98,

Windows®98 SE, Windows®2000 and Windows NT®4.0 are

registered trademarks of Microsoft Corporation. Intel®, Pentium®III

and CeleronTM are registered trademarks of Intel Corporation. VIA

CyrixIII is a registered trademark of VIA Technologies, Inc. Award is a

registered trademark of Award Software, Inc. Other trademarks and

registered trademarks of products appearing in this manual are the

properties of their respective holders.

Caution:

Danger of explosion if battery incorrectly replaced.

Replace only with the same or equivalent type recommended by the

manufacturer.

Dispose of used batteries according to the battery manufacturers

instructions.

FCC and DOC Statement on Class B

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a residential

installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the

following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and the receiver.

 Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

 Consult the dealer or an experienced radio TV technician for

help.

Notice:

1. The changes or modifications not expressly approved by the

party responsible for compliance could void the user's authority

to operate the equipment.

2. Shielded interface cables must be used in order to comply with

the emission limits.

Quick Setup Guide

Quick Setup

Guide

Table of Contents

Chapter 1

Quick Setup Guide.............................................

Chapter 2

English......................................................................

Chapter 3

Français (French).................................................

Chapter 4

Deutsch (German)................................................

Chapter 5

Español (Spanish)..................................................

Quick Setup Guide

Quick Setup

Guide

Chapter 1 - Quick Setup Guide

Table of Contents

1.1 System Board Layout..................................................................................................

1.2 Jumpers.....................................................................................................................................

1.3 Ports and Connectors................................................................................................

1.4 Award BIOS Setup Utility.......................................................................................

Quick Setup Guide

Quick Setup

Guide

1.1 System Board Layout

Quick Setup Guide

Quick Setup

Guide

1.2 Jumpers

1.2.1 Frequency Ratio Settings - SW1

Black rectangle

denotes the part

that is protruding,

the adjustable

switch.

Important:

 The frequency ratio of some processors shown in the table may

have been locked by the manufacturer. If you are using this kind

of processor, setting an extended ratio for the processor will have

no effect. The system will instead use its factory default ratio.

 The frequency ratio of processors greater than 8x has been

locked by the manufacturer and will no longer have the flexibility

of using extended ratios. Therefore, the system will use the

processors factory default ratio.

--- --- 4x

--- 4.5x

333MHz 5x

Processor SW1

66MHz 100MHz

Freq.

Ratio

5.5x

Processor SW1

66MHz 100MHz

Freq.

Ratio

400MHz

433MHz

466MHz

500MHz

6.5x

7.5x

8x533MHz

500MHz

366MHz

133MHz

533MHz

133MHz

650MHz

700MHz 933MHz

866MHz

800MHz

750MHz 1GHz

800MHz 1.067GHz*

667MHz

733MHz

300MHz

300AMHz

550MHz

600MHz

Quick Setup Guide

Quick Setup

Guide

 At the time this document was printed, the CPU marked with

asterisk (*) is not yet available. It is included in the table for

reference only.

 The processors supported by the system board support VID

(Voltage Identification). The switching voltage regulator on the

system board will automatically set the voltage regulator

according to the voltage of the processor.

1.2.2 CPUs Front Side Bus - JP2 and JP3

2-3 On

1-2 On All Off

Warning:

Some processors, when overclocked, may result to the processors or

systems instability and are not guaranteed to provide better system

performance. If you are unable to boot your system due to

overclocking, make sure to set these jumpers back to their default

settings.

JP2

1-2 On

2-3 On

All Off

JP3

1-2 On

2-3 On

All Off

Auto*

66MHz

100MHz

133MHz

* denotes default setting

Quick Setup Guide

Quick Setup

Guide

1.2.4 Onboard Audio Codec - JP7, JP8 and JP9

1.2.3 Clear CMOS Data - JP6

2-3 On:

Clear CMOS Data

1-2 On: Normal

(default)

2-3 On:

Disable the Onboard

Audio Codec

1-2 On:

Enable the Onboard

Audio Codec

(default)

JP7 JP9JP8

Quick Setup Guide

Quick Setup

Guide

1.3 Ports and Connectors

1.3.1 PS/2 Mouse and PS/2 Keyboard Ports

Make sure to turn off your

computer prior to

connecting or disconnecting

a mouse or keyboard.

Failure to do so may

damage the system board.

PS/2 Mouse

PS/2 Keyboard

1.3.2 Parallel Port

Parallel Port

Indice

Manuali Scheda madre popolari di altre marche

ASROCK

ASROCK ROMED8-2T Manuale utente

Asus

Asus P2L97A Manuale utente

Winmate

Winmate IC70 Manuale utente

Asus

Asus MES-B Manuale utente

Grantech

Grantech SYS8F377VGGA-3OMN Manuale utente

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuale utente

Gigabyte

Gigabyte GA-9IVDT Manuale utente

Texas Instruments

Texas Instruments ADS8372EVM Manuale utente

Commell

Commell MS-C73 Manuale utente

IBT Technologies

IBT Technologies MB860 Manuale utente

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuale utente

Biostar

Biostar M7VIT Bravo Istruzioni per l'uso e l'installazione

Intel

Intel D33217CK Manuale utente

Asus

Asus F1A55-M LX PLUS R2.0 Manuale utente

EPC

EPC EPC9147C Manuale utente

Asus

Asus EX-B760M-V5 D4 Manuale utente

EPOX

EPOX MU-8KHA0010 Manuale utente

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manuale utente