Digi-Sense 60010-85 Manuale utente
DataLogR
RTD THERMOMETER
MODELNO.60010-85
Digi
-
Sense
®
Digi
-
Sense
®
Digi
-
Sense
®
CERTIFICATE OF
CONFORMANCE
This thermometer was calibrated using
equipment traceable to the National Insti-
tute of Standards and Technology (NIST).
This instrument conforms to
DIN IEC-751 revised to ITS-90.
The accuracy of the thermometer at the
time of calibration was within specifications
stated in the operating manual.
ModelNo.:__________________________
Serial Number:______________________
Date placed in service:________________
To purchase an NIST certificate of trace-
ability with test data and test date for meter
and probe, please contact your dealer or:
Barnant Company
28W092 Commercial Avenue
Barrington, Illinois USA 60010-2392
Toll-free: 800-637-3739
1
INTRODUCTION
Thisversatilehand-heldinstrumentprovideshighly
accuratetemperaturemeasurements inCelsiusor
Fahrenheitusinga100 ohmplatinumRTD,withan
alphaof0.003850or 0.003916.
This instrument covers the extended measuring
range of –200 to 1210 °C (–328to 2210°F).
Theinstrumentisdesignedforeasyoperation and
includesthefollowingfeatures:
• Operator selection oftemperature scale
• Resolution of 0.01° from –50.00°C to 99.99°C
(–58.00°Fto99.99°F)
• LCD with threefour-digitdisplays
•3-pincircularconnectorinput(matetoSwitchcraft
TA3Fplug)
• Hold feature for temporarily retainingareading
• Two-point fieldcalibration capability
• Low battery warning
• Stores orlogs up to 1000readings with real-time
markers
2
• Scrolls through allstored readings
• Displays MIN and MAX readings
• Interfaces with optional HEWLETT PACKARD®
infraredprinter or optionalRS-232-Cadapter
• Prints temperatureand time of reading
• Built-in tilt standforeasy hands-free operation
SAFETY PRECAUTIONS
VOLTAGES PRESENT AT
THE RTD MAY ALSO BE
PRESENT AT THE BATTERY TERMINALS.
ALWAYS DISCONNECT THE RTD WHEN
CHANGINGBATTERIES.
THIS INSTRUMENT IS
DESIGNED TO ACCEPT
LOWLEVELSIGNALSSUPPLIEDBYSTANDARD
100 OHM PLATINUM RTD’S. UNDER NO
CIRCUMSTANCES SHOULD THE INPUT
VOLTAGE EXCEEDTHE SPECIFIED 10V RMS.
DO NOT USE OR STORE
THIS INSTRUMENT IN
MICROWAVE OVENS OR ANY ABNORMALLY
HOT OR COLD AREAS.
WEAKBATTERIESSHOULD
NOT BE LEFT IN THE
INSTRUMENT. DEAD BATTERIES CAN LEAK
AND CAUSE DAMAGETO UNIT.
WARNING
DANGER
CAUTION
CAUTION
3
EU Declaration of Conformity
Name of Apparatus: RTD Logger
Model Number: 60010-85*
Description of Apparatus:Electronic thermometer
using an RTD probe
Barnant Company declares that the above model is
in conformity to the following harmonized standards
and directives:
Applicable Applicable Manufacturer’s
Directives Specifications Report Number
73/23/EEC EN61010-1/A2:1995 TR0076
93/68/EEC
89/336/EEC EN61326-1/A1:1998 TR0076
92/31/EEC
93/68/EEC
The last two digits of the year in which the current
configuration of the above model was assessed per
the LowVoltage Directive is :00.
*Evaluated for EMC as part of a system using the
AC Adapter, Model Number 600-0075.
Manufacturer:
Barnant Company Division
Cole-Parmer Instrument Company
28W092 Commercial Avenue
Barrington, IL 60010-2392
USA
Tel.:847-381-7050
Manufacturer’s Signature:
James W.Doll Date
VicePresident, Engineering
19 December, 2000
4
SPECIFICATIONS
RTD PROBES
Impedance: 100ohm@0°C(32°F)
Sensitivity (alpha): 0.003850 or 0.003916 ohm/
ohm/°Cselectable
Accuracy: ±0.06°F;±0.03°Cat0.01°resolution
±0.1°at0.1°resolution
±1°at1°resolution
LOGGER
Linearization:ConformstoDIN IEC 751, revised
toITS-90
Input Protection:10V rms
Display Update:0.6seconds per update
Connector: 3-pin circular connector input (mate
toSwitchcraftTA3F plug)
Battery
Size: Two AA, 1.5V alkaline ANSI-L40,
IEC-LR6
Life: >300hours continuous,typical
Display: LCD with 0.4 in high characters main
readout and 0.2 in high characters secondary
displays, 4 digits each display plus various
annunciators.
Temperature/Humidity Range
Operating:
StatedAccuracy: 10°Cto40°C
(50°Fto104°F)
UsefulRange: 0°Cto40°C
(32°Fto104°F)
Storage: –10°Cto60°C
(–14°Fto 140°F)
Humidity: 10%to90%
(non-condensing)
5
Dimensions
3 cm D x 8.4 cm W x 15.8 cm H
(1.2 in x 3.3 in x 6.2 in)
Weight with batteries:227 grams (8 ounces)
Ingress protection: MeetsIEC-529IP-54fordust
andwaterresistant enclosures.
Compliance: For CE Mark:
EN61326-1/A1:1998
(EU EMC Directive)
6
BATTERY INSTALLATION AND
REPLACEMENT
VOLTAGES PRESENT AT
THE RTD MAY ALSO BE
PRESENT AT THE BATTERY TERMINALS.
ALWAYS DISCONNECT THE RTD WHEN
CHANGING BATTERIES.
WEAKBATTERIESSHOULD
NOT BE LEFT IN THE
INSTRUMENT. DEAD BATTERIES CAN LEAK
AND CAUSE DAMAGETO UNIT.
CAUTION
DANGER
7
If battery indicator turns on, battery life is
approximately8 to 10 hours.Thebattery indicator
will start blinking with less than 1 hour of life
remaining.
ATTHISPOINT,BATTERYMUSTBECHANGED.
IFBATTERYVOLTAGEGOESTOOLOW,DISPLAY
WILL GO BLANK.
SeeSPECIFICATIONS forbattery type.
1. Before changingbattery,turninstrumentoffand
disconnectprobe.
2. Loosen screw and lift battery cover off back of
case.
3. Remove the twoAAbatteries.
4. Inserttwonew batteries,observing polarity.
5. Install cover and tighten screw.
AC ADAPTER
An optional AC adapter can be used for power to
conserve batteries.The adapter is not a charger
andwillnotchargebatteries.Theadapterconnects
tothebottomofthethermometer.Whentheadapter
isconnected,thebatteriesaredisconnected.Refer
to the ACCESSORIES section for adapter
information.
8
CONNECTING AN RTD
Note:Besureyourinstrument settingmatchesthe
RTDyouareusing(alphaof0.00385or0.003916).
See SELECTING RTD SENSITIVITY (ALPHA)
on page 14.Insert the 3-pin plug into the mating
connector on the top of the instrument.
Indice
Altri manuali Digi-Sense Termometro
Digi-Sense
Digi-Sense 20250-34 Manuale utente
Digi-Sense
Digi-Sense 20250-01 Manuale utente
Digi-Sense
Digi-Sense Dual J-T-EK 60010-40 Manuale utente
Digi-Sense
Digi-Sense 20250-07 Manuale utente
Digi-Sense
Digi-Sense J Manuale utente
Digi-Sense
Digi-Sense Dual J-T-E-K 91100-40 Manuale utente
Digi-Sense
Digi-Sense Type K Manuale utente
Digi-Sense
Digi-Sense ThermoLogR 93410-50 Manuale utente
Digi-Sense
Digi-Sense 20250-25 Manuale utente
Digi-Sense
Digi-Sense 20250-02 Manuale utente
Digi-Sense
Digi-Sense DualLogR 91100-50 Manuale utente
Digi-Sense
Digi-Sense 91428-03 Manuale utente
Digi-Sense
Digi-Sense 91428-06 Manuale utente
Digi-Sense
Digi-Sense 20250-30 Manuale utente
Digi-Sense
Digi-Sense 20250-91 Manuale utente
Digi-Sense
Digi-Sense 93410-00 Manuale utente
Digi-Sense
Digi-Sense 20250-91 Manuale utente
Digi-Sense
Digi-Sense 20250-05 Manuale utente
Digi-Sense
Digi-Sense 20250-18 Manuale utente
Digi-Sense
Digi-Sense 20250-32 Manuale utente
