Dilog DL9206 Manuale utente

DL9206 AUTORANGING

MULTIMETER

operating manual

61010-1

CAT III

600V

Safety Information

This manual contains information that must be

followed for operating the meter safely and

maintaining the meter in a safe operating condition.

If this meter is not used in the manner speciﬁed, the

protection provided may be impaired.

Warning! Warns of potential danger, refer to the

instruction manual to avoid personal injury or

damage to the meter.

Caution! Dangerous voltage. Danger of electrical

shock.

Continuous double or reinforced insulation

complies with IEC536, class II.

Symbol of conformity, conﬁrms conformity with

relevant EU directives. The meter complies with

EMC directives (89/336/EEC). Speciﬁcally stand-

ards EN 50081-1 and EN 50082-1 as well as the

Low Voltage Directive (73/23/EEC) described in

the standard EN 61010-1.

Safety Information

The meter has been designed in accordance with

the safety regulations for electronic measuring

instruments, EN 61010-1, IEC 61010.

Voltages above 75V DC or 50V AC may constitute a

serious shock hazard.

Before using the meter check for physical damage to

the casing in particular around the connectors. If the

case is damaged do not use the meter.

Check the test leads for damaged insulation or

exposed metal. Check the leads for continuity.

Replace damaged leads with identical model or

speciﬁcation before using the meter.

Where applicable use GS38 approved leads (not

supplied) these are available from Di-Log. When using

test leads keep ﬁngers behind the ﬁnger guards.

Do not apply more than the rated voltage, as marked

on the meter between the terminals or between any

terminal and ground.

Safety Information

Before making a measurement ensure that the rotary

switch is set to the appropriate range. Do not turn the

rotary switch whilst making a measurement.

Use the appropriate terminals, function and range for

your measurements. If the value to be measured is

not known use the maximum measurement position

and reduce the range step by step until a satisfactory

reading is obtained.

Do not use or store the meter in an environment of

high temperature, humidity, fumes, vapour, gaseous,

inﬂammable and strong magnetic ﬁeld. The perform-

ance and safety of the use may be compromised in

such circumstances.

Disconnect circuit power and discharge all high

voltage capacitors before testing resistance,

continuity, diodes, capacitance or current.

Before measuring current check the meters fuses and

turn off power to the circuit before connecting the

meter to the circuit.

Safety Information

Replace the battery as soon as the low battery

indicator appears. If the battery is low the meter

may give false readings.

Turn the meter power off when not in use,. Remove

the battery if the meter is in use for a long period.

Constantly check the battery as it may have leaked.

A leaking battery will damage the meter.

The meter may only be opened by a qualiﬁed service

technician for calibration and repair.

Input Limits

Symbols and Annunciators

Continuity

BAT Low Battery

Diode

HOLD Data Hold

AUTO AutoRanging

AC Alternating Current or Voltage

DC Direct Current or Voltage

Never apply voltage or current to the meter that exceeds

the speciﬁed maximum:

Function Maximum

V DC or V AC 1000V DC, 750V AC

A DC/AC 10A DC/AC

(30 seconds max every 15 minutes)

Frequency, Resistance, 250V DC/AC

Capacitance, Duty Cycle,

Diode test, Continuity

Temperature 250V DC/AC

1. 6000 count Liquid Crystal Display with symbolic signs.

2. Function rotary switch.

3. 10A (positive) input terminal for 10A DC or AC

measurements.

4. COM (negative) input terminal.

5. Positive input terminal.

6. HOLD pushbutton.

7. Max/Min pushbutton.

8. Range/ Diode pushbutton.

9. Hz/Duty pushbutton.

Controls and Inputs

Speciﬁcations

The instrument complies with: EN61010-1.

Insulation: Class2, Double insulation.

Overvoltage category: CATIII 600V.

Display:

6000 counts LCD display with function indication.

Polarity: Automatic, (-) negative polarity indication.

Overrange: “OL” mark indication.

Low battery indication: The “BAT” is displayed when

the battery voltage drops below the operating level.

Measurement rate: 2 times per second, nominal.

Auto power off: Meter automatically shuts down after

approx. 15 minutes of inactivity.

Operating environment: 0˚C to 50˚C (32˚F to 122

˚F) at < 70 % relative humidity.

Storage temperature: -20˚C to 60˚C (-4˚F to 140˚F)

at < 80 % relative humidity.

For inside use, max height: 2000m

Pollution degree: 2

Power: One 9V battery , NEDA 1604, IEC 6F22.

Dimensions: 150 (H) x 70 (W) x 48 (D) mm

Weight: Approx.: 255g.

Accuracy is given at 18˚C to 28˚C (65˚F to 83˚F), less than 70 % RH

Speciﬁcations

DC Current (Auto-ranging for uA and mA)

Range Resolution Accuracy

10A 1mA ±2.5% of rdg + 5 dgts

Overload Protection: 10A / 250V Fuse.

Maximum Input: 10A dc or ac rms on 10A DC range..

DC Voltage

Range Resolution Accuracy

600.0mV 0.1mV ±0.5% of rdg + 2 dgts

6.000V 1mV

60.00V 10mV ±1.2% of rdg + 2 dgts

600.0V 100mV

1000V 1V ±1.5% of rdg + 2 dgts

Input Impedance: 7.8MΩ.

Maximum Input: 1000V dc or 750V ac rms.

AC Current (Auto-ranging for uA and mA)

Range Resolution Accuracy

10A 1mA ±3.0% of rdg + 7 dgts

Overload Protection: 10A / 250V Fuse.

Frequency Range: 50 to 60 Hz.

Maximum Input: 10A dc or ac rms on 10A AC range.

AC Voltage

Range Resolution Accuracy

6.000V 1mV +1.2% of rdg + 3 dgts

60.00V 10mV +1.5% of rdg + 3 dgts

600.0V 100mV

750V 1V +2.0% of rdg + 4 dgts

Input Impedance: 7.8MΩ.

Frequency Range: 50 to 60Hz .

Maximum Input: 1000V dc or 750V ac rms..

Speciﬁcations

Resistance (Auto-ranging)

Range Resolution Accuracy

600.0Ω 0.1Ω ±1.2% of rdg + 4 dgts

6.000kΩ 1Ω ±1.0% of rdg + 2 dgts

60.00kΩ 10Ω ±1.2% of rdg + 2 dgts

600.0kΩ 100Ω

6.000MΩ 1kΩ

60.00MΩ 10kΩ ±2.0% of rdg + 3 dgts

Input Protection: 250V dc or 250V ac rms.

Capacitance (Auto-ranging)

Range Resolution Accuracy

40.00nF 10pF ±5.0% of rdg + 7 dgts

400.0nF 0.1nF

4.000uF 1nF ±3.0% of rdg + 5 dgts

40.00uF 10nF

400.0uF 0.1uF ±5.0% of rdg + 5 dgts

4000uF 1uF ±5.0% of rdg + 5 dgts

Input Protection: 250V dc or 250V ac rms.

Frequency (Auto-ranging)

Range Resolution Accuracy

6.999Hz 0.001Hz

69.99Hz 0.01Hz ±1.5% of rdg + 5 dgts

699.9Hz 0.1Hz

6.999kHz 1Hz

69.99kHz 10Hz ±1.2% of rdg + 3 dgts

699.9kHz 100Hz

2.999MHz 1kHz ±1.5% of rdg + 4 dgts

Sensitivity: >0.5V RMS while ≤ 1MHz ;

Sensitivity: >3V RMS while >1MHz ;

Overload protection: 250V dc or ac rms.

Indice

Altri manuali Dilog Multimetro

Dilog

Dilog PL280N Manuale utente

Dilog

Dilog DL9204 Manuale utente

Dilog

Dilog DL9205 Manuale utente

Dilog

Dilog DL9308 Manuale utente

Dilog

Dilog DL9307 Manuale utente

Dilog

Dilog 9908 Manuale utente

Manuali Multimetro popolari di altre marche

Agilent Technologies

Agilent Technologies 34420A Manuale utente

Fluke

Fluke 83 Manuale utente

Hameg

Hameg HM 8012 Manuale utente

Mastech

Mastech MY70 Manuale utente

Steren

Steren MUL-300 Manuale utente

Somogyi Elektronic

Somogyi Elektronic home SMA 92 Manuale utente

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 Manuale utente

PeakTech

PeakTech 4000 Manuale per l'uso e la cura

YOKOGAWA

YOKOGAWA 90050B Manuale utente

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 Manuale utente

Fluke

Fluke 8846A Manuale operativo e di manutenzione

Tempo Communications

Tempo Communications MM200 Manuale utente

Elenco Electronics

Elenco Electronics CM-1555 Manuale utente

Mastech

Mastech MS8238C Manuale utente

SDAR

SDAR 830A, 830B, 830D, 830C Manuale utente

RS PRO

RS PRO RS-9519BT Manuale utente

BGS technic

BGS technic 8890 Manuale utente

Amprobe

Amprobe Hexagon 60 Manuale utente