Dini Argeo T Series Manuale utente
0
Modules for electronic weighing
ELECTRONIC PLATFORMS
T and TE SERIES
Installation and operating manual
T_TE_SERIE_14.07_EN
1
INDEX
IMPORTANT WARNINGS ............................................................................... page 2
1 - INTRODUCTION......................................................................................... page 3
1.1 –TECHNICAL SPECIFICATIONS ..............................................................page 3
2 - INSTALLATION .......................................................................................... page 4
2.1 –INSTALLING THE TCA COLUMN............................................................page 8
2.2 –INSTALLING THE TCB COLUMN............................................................page 9
3 –MAINTENANCE AND REPAIRS................................................................ page 10
4 –TRANSPORTING THE PLATFORM .......................................................... page 10
5 –SHIELDED CABLE .................................................................................... page 10
INDICATOR JUNCTION BOX CABLE...............................................................page 10
WARRANTY AND AUTHORIZED SERVICE CENTRE.................................... page 11
2
IMPORTANT WARNINGS
Put the platform in a place in which the following conditions are respected:
-Flat, level, stable support surface
- Stable and absent of vibrations,
-Absence of dust or aggressive vapours,
- Absence of air currents,
- Moderate temperature and humidity (not exposed to direct sunlight or near heat sources).
Make sure to level the platform by adjusting the feel and checking air bubble level (see INSTALLATION
instructions).
Do not weld, perforate or modify the structure without consulting the reseller. If it is damaged or tampered
with the warranty conditions will be annulled.
If the place of use is a humid or wet environment, the installation must be carried out in such a way so
that water stagnation and/or scraps under the structure are avoided.
The platform must be connected to a weigh indicator. Refer to weigh indicator owner’s manual for
connection instruction.
Do not step, crush or expose to sunlight the connecting screen cable.
DO NOT INSTALL IN HAZARDOUS ENVIRONMENTS.
(unless specifically made for this use)
Do not use solvents when cleaning.
3
1 –INTRODUCTION
All weighing modules are built with high quality materials and are calibrated in such a way, which
guarantees full reliability and weighing accuracy that lasts in time. The measuring elements are load cells,
produced in conformance to the OIML R60 standards.
The T and TE platforms have load cells connected to the indicator with a 6-pin shielded cable, 3 meters of
length.
Every weighing module is built and engineered to guarantee a uniform detection of the load on the load
cell weighing modules, even in adverse environment conditions.
The electronic weighing platform T and TE series, are suitable for creating weighing systems or small and
medium, capacity, piece counter. The weigh capacity goes from 0,6 kg to 600 kg.
The Tseries platform have a structure made of tubular steel, oven fire painted black, and satined AISI 304
stainless steel loading surface. The measuring element consists of an approved aluminium “single point”
load cell according to OIML R60 standards with protection against dust and moisture according to IP65
standards.
The TE series platform have a structure made with tubulars, mechanics, trinkets and satined steel loading
surface in AISI304 stainless steel. The measuring element consists of an approved “single point”
STAINLESS STEEL load cell according to OIML R60 standards with protection against dust and moisture
according to IP68 standards (for the TSNE and TTNE version the protection is IP67).
1.1 - TECHNICAL SPECIFICATIONS
Load cell off-center direct load
Power supply 15 Vcc
Nominal output (max. load) 2 mV/V ±10% (platform related)
Operating temperature range -10 / + 50 °C
ACCESSORIES
Indicator holder column (integral with platform).
Floor-mounted indicator column.
Various types of conveyor carriages.
Junction box IP67.
4
2 - INSTALLATION
Refer to Figure 1, Figure 2 and Figure 3.
NOTE: The weighing module must be connected to its appropriate weight indicator with the cable
coming from the load cell. The indicator, connected to the platforms, can not be calibrated if not
powered.
It is the customer’s responsibility to prepare and calibrate the indicator.
For any further detail, refer to the technical and operational manual, supplied with the indicator.
a) Unpack then product. Pick up and remove plate (1).
b) Remove the locking strips (2).
Keep and reuse the wooden strips, in the event the platform needs to be moved again
c) Take off the bands which keep fixed the underplate (see fig.2 and fig.3)
d) Level the platform by adjusting the adjustable feet (3) until the bubble (4) is in the centre of the level.
The stability of the platform is very important.
ALL THE CORNERS MUST REST IN A UNIFORM WAY. Carefully check that all feet fully rest on the
ground and that the platform, loaded on the corner, is not unstable (if a corner is not resting on the
ground its relative foot is easier to turn).
e) Never remove the red painted bolts and nuts.
f) Reposition plate (1).
g) Connect the shielded cable from the load cell (5) to the weigh indicator (refer to the indicator manual).
The cable must be free, so that the resistances are not energised, which could alter the measurement.
h) You need to ground the metallic structure of the platform using the appropriate plug, which has this
symbol , especially if you need to weigh materials that, while handled, can cause electrical
discharges (dust, plastic materials, etc.). If there are any doubts, consult the reseller.
i) Make sure to follow the warnings at page 2.
5
Fig.1
SHIELD CABLE
INDICATOR
2 WOODEN STRIP USED FOR
TRANSPORT TO BE REMOVED LIKE
SHOWN
GROUND
PLUG
6
Fig.2
Remove the band
Remove the band
7
Fig.3
Remove the band
Remove the band
8
2.1 –INSTALLING THE TCA COLUMN
n.
q.ty
description
1
1
DFWL, DFWLI, CPWET e TRI
Indicators
2
1
Stainless steel column
3
1
DFWL holder
4
1
Foot
5
2
M6x1 hexagonal nut
6
1
Platform series T or TE
7
4
M6x12 screws
8
2
6.4x18 washer
9
2
M4x6 screw
10
2
M6x12 screw
9
2.2 –INSTALLING THE TCB COLUMN
Components:
1. DFWLI indicator
2. n.2 M6 exagonal nuts
3. n.1 column TCBI350-1, TCBI500-1 or TCBI700-1
4. n.4 VTC M6X16 inox (screw)
5. Platform
Please note that the M6 hex nuts (part 2) are supplied with the DFWLI. Remove the DFWLI wall brackets
and use nuts for connection to the column.
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Dini Argeo Scala
Dini Argeo
Dini Argeo ALP Manuale utente
Dini Argeo
Dini Argeo APM Manuale utente
Dini Argeo
Dini Argeo TPW E-FORCE Manuale di istruzioni
Dini Argeo
Dini Argeo HLD Series Manuale utente
Dini Argeo
Dini Argeo MCW PROFESSIONAL Manuale utente
Dini Argeo
Dini Argeo TPW Series Istruzioni operative
Dini Argeo
Dini Argeo MCW Guida
Dini Argeo
Dini Argeo DGT100 Manuale utente
Dini Argeo
Dini Argeo MCWN Series Istruzioni operative
