DMP Electronics 712-8 Manuale utente

712-8 ZONE EXPANSION MODULE

Installation Guide

DESCRIPTION

MODEL

712-8

The Model 712‑8 Zone Expansion

Module allows you to increase

the number of protection zones

available on a DMP panel. The 712‑8

provides a total of eight grounded

zones.

The zone expansion module

provides a terminal strip for zone

inputs, two 4‑pin headers for

Keypad Bus or LX‑Bus connections,

a jumper for LX‑Bus or Keypad Bus

operation, and a transmit data LED

to indicate panel communication.

Note: The 712‑8 is listed for use in

burglary applications only: No ﬁre

circuits shall be used on this device.

Compatibility

• XT30/XT50 Series panels

• XR150/XR550 Series panels

What is Included?

• One 712‑8 Zone Expansion

Module

• Eight 1K Ohm EOL resistors

1MOUNT THE MODULE

Themodule can be mounted in a DMP enclosure using the

standard3‑hole mounting pattern. Refer to Figure 2as needed

during installation.

1. Hold the plastic standos against the inside of the enclosure

side wall.

2. Insert the included Phillips head screws from the outside of

the enclosure into the standos. Tighten the screws.

3. Carefully snap the module onto the standos.

WIRE THE MODULE

2Use18to22gauge wire to connect the712‑8 directly to the

Keypad Bus or use a dual‑ended4‑wire harness to connect

directly to the LX‑Bus. This connection allows the module to

communicate with the panel and receive12VDC power. For more

information about wiring, refer to Wiring Speciﬁcations. Refer to

Figure 3when wiring themodule.

Connect to the LX‑Bus

1. Place a jumper across the top two KEYPAD/LX‑BUS pins.

2. Connect one end of a4‑wire harness to the top header on

the module.

3. At the panel, connect the other end of the4‑wire harness

to the LX‑Bus.

Connect to the Keypad Bus

1. Place a jumper across the bottom two KEYPAD/LX‑BUS

pins.

2. Connect a4‑wire harness to thetop header on the module.

3. At the panel, connect the wires to the corresponding

Keypad Bus terminals.

Figure 1: 712-8 Module

Figure 2: Stando and Module Installation

BACK

2 712-8 INSTALLATION GUIDE | DIGITAL MONITORING PRODUCTS

3To communicate the status of the eight zones, the module

responds to two addresses on the Keypad Bus and eight

addresses on the LX‑Bus. You can set the module starting

address to any bus address from 0to 15. The module

automatically responds to this address, the next address

on the Keypad Bus, and the next seven addresses on the

LX‑Bus.

To change the current address, move the slide switches to

the appropriate address positions according to Figure 4.

Keypad Bus Addressing

The module can be set to the following keypad addresses

according to panel model: 1through 8for XT30/XT50

and XR150 Series panels, or1through 15for XR550Series

panels. Additionally, the eight zones on the module occupy

two keypad addresses.

For example, if the module is set to address2, the ﬁrst four expansion zones occupy address 2and respond

as zones 21‑24. The last four expansion zones occupy address 3and respond to the panel as zones 31‑34. For

more information about Keypad Bus addressing, refer to Table1.

Note: Because the 712‑8 is supervised, both addresses must be selected in Device Setup of the

XR150/XR550Series programming when used on the Keypad Bus.

LX‑Bus Addressing

When connecting to the LX‑Bus, the module must be addressed to match the last two digits of the

ﬁrst zone being used. The next seven zone addresses are automatically used to communicate expander

zones2through8status.

For example, on an XR150panel using LX‑Bus 1if you set the module address to8, the eight zones on the

expander respond as zones 508to 515. When connected to an XR550panel using LX‑Bus 2, the zones respond

as 608to 615. For more information about LX‑Bus addressing, refer to Table2.

Note: Only two 712‑8 Modules can be connected to each LX‑Bus.

ADDRESS THE MODULE

Z1 Z2 Z3 Z4 Z5 Z6 Z7 Z8GND GND GND GND

KEYPAD

LX-BUS

TXD

BLK

RED

712-8

1234 5 6 7 810 11 12 13 14 15 16 17 18

+B BELL GND SMK GND

RED YEL GRN BLK Z1 Z2 Z3 Z4 Z5

AC -B GND

GND

Z10+

Z10-

RED

PROG

XT30

To other zone

expansion modules

on the same bus.

1K EOL 1K EOL

1K EOL

1K EOL Zone 1

Zone 2

Zone 3

Zone 4

Zone 8

Zone 7

Zone 6

Zone 5

Use supplied 1K EOL resistors on each zone.

Normal operating range is 650-1200 Ohms

These 4-pin headers are connected

together internally to allow bus

connection of other zone expansion

modules.

ADDRESS

Figure 3: Wiring Diagram

1 2 3 4

5 6 7 8

9 10 11 12

13 14 15 0

Figure 4: Addressing the Module

712-8 INSTALLATION GUIDE | DIGITAL MONITORING PRODUCTS 3

ADDITIONAL INFORMATION

Wiring Speciﬁcations

DMP recommends using 18 or 22 AWG for all LX‑Bus and Keypad Bus connections. The maximum wire distance between

any module and the DMP Keypad Bus or LX‑Bus circuit is 10 feet. To increase the wiring distance, install an auxiliary

power supply, such as a DMP Model 505‑12. Maximum voltage drop between a panel or auxiliary power supply and any

device is 2.0 VDC. If the voltage at any device is less than the required level, add an auxiliary power supply at the end of

the circuit.

To maintain auxiliary power integrity when using 22‑gauge wire on Keypad Bus circuits, do not exceed 500 feet. When

using 18‑gauge wire, do not exceed 1,000 feet. Maximum distance for any bus circuit is 2,500 feet regardless of wire

gauge. Each 2,500 foot bus circuit supports a maximum of 40 LX‑Bus devices.

For additional information refer to the LX‑Bus/Keypad Bus Wiring Application Note (LT‑2031) and the 710 Bus Splitter/

Repeater Module Installation Guide (LT‑0310).

Connecting to Other Modules

Using a 4‑wire connector as an extension of the Keypad Bus or LX‑Bus, you can easily connect the 712‑8 to multiple

modules on the same bus. Observe wire colors when making connections. For more information about wiring

connections, refer to Figure 3.

Data LED

The LED on the 712‑8 ﬂashes each time the module responds to a poll from the panel. If there is a problem with the

panel, system programming, or the connection between the panel and module, the LED stops ﬂashing and a system

trouble message displays on the keypad.

Compliance Listing Speciﬁcations

UL Commercial Burglary

The 712‑8 Zone Expansion Module must be mounted inside the control unit enclosure or other Listed enclosure.

ULC Commercial Burglary (XR150/XR550 Series Panels)

If the 712‑8 is installed in another enclosure, a DMP Model 307 Clip‑on Tamper Switch programmed as a 24‑Hour zone is

required.

The 712‑8 zones can only be used in Low Risk applications. Medium or High Risk applications must use panel zone

inputs.

DMP PANEL

KEYPAD BUS

712-8

ADDRESS

EXPANDER ZONES

1-4 5-8

PANEL ZONES

XT30/XT50Series,

XR150/XR550

Series

1 11‑14 21‑24

2 21‑24 31‑34

3 31‑34 41‑44

4 41‑44 51‑54

XT30/XT50Series,

XR150/XR550

Series

5 51‑54 61‑64

6 61‑64 71‑74

771‑74 81‑84

8 81‑84 91‑94

XR550 Series

9 91‑94 101‑104

10 101‑104 111‑114

11 111‑114 121‑124

12 121‑124 131‑134

13 131‑134 141‑144

14 141‑144 151‑154

15 151‑154 161‑164

712-8

ADDRESS

XR150/XR550 SERIES LX-BUS

PANEL ZONE RANGE

LX-BUS 1 LX-BUS 2 LX-BUS 3 LX-BUS 4 LX-BUS 5

0 500‑507 600‑607 700‑707 800‑807 900‑907

1 501‑508 601‑608 701‑708 801‑808 901‑908

2 502‑509 602‑609 702‑709 802‑809 902‑909

... ... ... ... ... ...

7 507‑514 607‑614 707‑714 807‑814 907‑914

8 508‑515 608‑615 708‑715 808‑815 908‑915

9 509‑516 609‑616 709‑716 809‑816 909‑916

... ... ... ... ... ...

12 512‑519 612‑619 712‑719 812‑819 912‑919

13 513‑520 613‑620 713‑720 813‑820 913‑920

14 514‑521 614‑621 714‑721 814‑821 914‑921

15 515‑522 615‑622 715‑722 815‑822 915‑922

Table 1: Keypad Bus Addresses

Table 2: LX-Bus Addresses

Designed, engineered, and

manufactured in Springﬁeld, MO

using U.S. and global components.

LT-0687 1.03 20021

712-8 ZONE

EXPANSION MODULE

Speciﬁcations

Operating Voltage 8.0 to 14.5VDC

Current Draw

Normal 17mA + 1.6mA per active zone

Alarm 17mA + 2.0mA per active zone

Dimensions 4.50” W x 2.50” H

11.43 cm W x 5.08 cm H

Weight 8.0oz (23.0 kg)

Compatibility

XT30/XT50 Series Panels

XR150/XR550 Series Panels

Certiﬁcations

FCC Part 15

Underwriters Laboratory (UL) Listed

ANSI/UL 365 Police Station Connected Burglar

ANSI/UL 609 Local Burglar Alarm Unites and

Systems

ANSI/UL 1023 Household Burglar Alarm System

Units

ANSI/UL 1076 Proprietary Burglar Alarm Units

ANSI/UL 1610 Central Station Burglar Alarm Units

ANSI/UL 1635 Digital Burglary

ULC Subject-C1023 Household Burglar

ULC/ORD-C1076 Proprietary Burglar

ULC S304 Central Station Burglar

MODEL

712-8

INTRUSION • FIRE• ACCESS• NETWORKS

2500 North Partnership Boulevard

Springﬁeld, Missouri 65803-8877

800.641.4282 | DMP.com

FCC INFORMATION

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. this device must accept any interference received, including interference that may cause undesired operation.

The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm (7.874 in.) from

all persons. It must not be located or operated in conjunction with any other antenna or transmitter.

Changes or modiﬁcations made by the user and not expressly approved by the party responsible for compliance could

void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the equipment o and on,

the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

4. Consult the dealer or an experienced radio/TV technician for help.

Altri manuali DMP Electronics Unità di controllo

DMP Electronics

DMP Electronics 711S Manuale utente

DMP Electronics

DMP Electronics 734N Series Guida all'installazione

DMP Electronics

DMP Electronics 893A Manuale utente

DMP Electronics

DMP Electronics RoBoard RM-G145 Manuale utente

DMP Electronics

DMP Electronics Wiegand 734N Manuale utente

DMP Electronics

DMP Electronics 734N-WIFI Guida per l'amministratore

DMP Electronics

DMP Electronics RoBoard RM-G144 Manuale utente

DMP Electronics

DMP Electronics 734 Manuale utente

DMP Electronics

DMP Electronics 277CAN Manuale utente

DMP Electronics

DMP Electronics 714 Manuale utente

DMP Electronics

DMP Electronics 734 Guida all'installazione

DMP Electronics

DMP Electronics 1134 Guida all'installazione

DMP Electronics

DMP Electronics 893A Manuale utente

DMP Electronics

DMP Electronics RoBoard RM-G146 Manuale utente

DMP Electronics

DMP Electronics 780 Guida all'installazione

DMP Electronics

DMP Electronics 716 Manuale utente

DMP Electronics

DMP Electronics 734B Guida all'installazione

DMP Electronics

DMP Electronics 736P Radionics Manuale utente

DMP Electronics

DMP Electronics RoBoard RM-G211 Manuale utente

DMP Electronics

DMP Electronics 865 Manuale utente

DMP Electronics

DMP Electronics 734 Guida all'installazione

DMP Electronics

DMP Electronics 708 Manuale utente

DMP Electronics

DMP Electronics 734INT Guida all'installazione

DMP Electronics

DMP Electronics SCS-104 Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente