Dräger Alcotest 6000 Manuale utente

Dräger Alcotest®6000

WARNING

Strictly follow the Instructions for Use.

The user must fully understand and strictly observe the instructions.

Use the product only for the purposes specified in the Intended use

section of this document.

enUS Instructions for use

3

es Instrucciones de uso

21

11 1310

00100217.ai

Safety-related information

1 Safety-related information

Before using this product, carefully read these instructions for use and those

of the associated products.

Strictly follow the instructions for use. The user must fully understand and

strictly observe the instructions. Use the product only for the purposes

specified in the intended use section of this document.

Do not dispose of the instructions for use. Ensure that they are retained and

appropriately used by the product user.

Only trained and competent users are permitted to use this product.

Comply with all local and national rules and regulations associated with this

product.

Only trained and competent personnel are permitted to inspect, repair and

service the product. Dräger recommend a Dräger service contract for all

maintenance activities and that all repairs are carried out by Dräger.

Do not use a faulty or incomplete product. Do not modify the product.

Notify Dräger in the event of any component fault or failure.

Use only genuine Dräger spare parts and accessories. Otherwise, the

proper functioning of the product may be impaired.

These instructions for use can be downloaded in other languages in

electronic form on the relevant product page (www.draeger.com/ifu), or a

free printed copy can be obtained from Dräger or the distributor.

Only use battery chargers, power packs, batteries, or rechargeable batteries that

Dräger has approved for this product.

2 Conventions used in this document

2.1 Meaning of the alert icons

The following alert icons are used in this document to notify the user of possible

dangers. The meanings of the alert icons are defined as follows:

WARNING

Indicates a potentially hazardous situation. If not avoided, it could result in death

or serious injury.

Description

CAUTION

Indicates a potentially hazardous situation. If not avoided, it could result in

physical injury. It may also be used to alert against unsafe practices.

NOTICE

Indicates a potentially hazardous situation. If not avoided, it could result in

damage to the product or environment.

2.2 Typographical conventions

This symbol indicates information that may make the use of this product

easier.

3 Description

3.1 Product overview (see Page 2)

1 Breath-alcohol analyzer

2 button (switch instrument on/off, confirm entry)

3 button (access menu, set value)

4 LEDs

5 Mouthpiece receptacle (configurable: right or left)

6 Display

7 button (set value)

8 USB connection (Important: Not for charging the device, for service only)

9 Wrist strap

10 Battery compartment cover

11 Battery

12 Pull strap for battery replacement

13 Loudspeaker (Important: No reset button)

14 Mouthpiece

Text Text in bold refers to labeling on the device and screen text.

►This triangle indicates options for avoiding the hazard in

warnings.

Use

3.2 Intended use

The Dräger Alcotest®60001) breath-alcohol analyzer is used to measure the

alcohol concentration in human breath. The measurement is used as an

indication for alcohol intoxication. It is not permitted for therapeutic measures to

be initiated on the basis of the measurement.

4 Use

WARNING

Small parts of the device may become detached and be swallowed.

The device is not intended for children under 3 years.

4.1 Prerequisites for use

The device is factory-calibrated when delivered. If the calibration date is longer

ago than 12 months, the instrument should be calibrated, e.g., by DrägerService.

Observe a wait time of approx. 15 minutes after the last consumption of

alcohol.

The wait time cannot be reduced by rinsing your mouth with water or with

non-alcoholic beverages.

Residual mouth alcohol or aromatic beverages (e.g., fruit juice), mouth

sprays containing alcohol, medication and drops, as well as belching and

vomiting may cause incorrect measuring values.

Rinsing the mouth with water or non-alcoholic drinks does not replace the

wait time!

4.1.1 Before sampling

The subject must breathe regularly and calmly before sampling.

The subject must be able to provide the required minimum breath volume

for the sampling.

4.1.2 Attaching the wrist strap

The wrist strap should be used to secure the device on the wrist.

1. Guide the fastening lug on the wrist strap through the eye on the device.

2. Pull the top part of the wrist strap through the fastening lug.

1) Alcotest®is a registered trademark of Dräger.

Use

4.1.3 Preparation for use

1. Ensure that the batteries are charged and inserted.

2. Ensure that a clean mouthpiece is attached.

3. Ensure that the device is held firmly and securely by using the wrist strap as

intended.

4.1.4 Switching the instrument on and off

Switching the instrument on:

1. Hold down the button for about 1 second.

2. Wait until the instrument displays that it is ready to measure.

Switching the device off:

1. Hold down the button for about 3 seconds. A switch-off count down will

be shown as well. If the display is off, stop pressing the button. Otherwise

the device will be switched on again.

The instrument will switch off automatically approx. 2 minutes after the last

use.

Switching off the instrument does not reduce the post-test waiting period

before you can perform another test.

4.2 Initial start-up

A setup wizard is opened when the instrument is switched on for the first time.

This step is not required for pre-configured instrument.

The following settings are made using the setup wizard:

Language

Date format

Date

Time format

Time

Measuring unit

All settings can be changed later on via the menu.

Language

A cursor pre-selects one language in the list. Press briefly on the button to

change the position of the cursor in order to select your needed language. If the

Use

cursor selects the right language please hold the button for approx. 2 seconds to

confirm.

Date

A cursor pre-selects the day of the date. Press briefly on the button to change

the day until the actual day is shown. Please hold the button for approx.

2 seconds to confirm the day. Please continue with the month and the year in the

same way: short press to change and long press to confirm.

Time format

A cursor pre-selects a time format. Press briefly on the button to change the

position of the cursor in order to select your needed time format. If the cursor

selects the needed time format please hold the button for approx. 2 seconds to

confirm.

Time

A cursor pre-selects the hours of the time. Press briefly on the button to change

the hour until the actual hour is shown. Please hold the button for approx.

2 seconds to confirm the hour. Please continue with the minutes in the same

way: short press to change and long press to confirm.

Measurement unit

A cursor pre-selects a measurement unit in the list. Press briefly on the button to

change the position of the cursor in order to select your needed measurement

unit. If the cursor selects the needed measurement unit, please hold the button

for approx. 2 seconds to confirm.

After the setup wizard is finished, the display shows Welcome and continues with

READY for tests.

The Alcotest®4000 is now adjusted to your settings and is ready for breath tests.

Of course these and further settings can be adjusted in the device menu (see

section 4.8 on page 10).

NOTICE

Loss of default settings

If the battery replacement process takes longer than 5 minutes, the date and

time must be reset. A measurement is only possible with the time set.

Use

4.3 Carrying out an automatic breath sample

A new mouthpiece must be inserted for each new person who provides a

breath test.

Do not allow any high alcohol concentrations on the sensor, e.g., by rinsing

the mouth with a high proof alcohol shortly before the measurement, as this

will shorten the service life of the sensor.

Procedure

1. Remove the mouthpiece (order no. 68 10 690 "Standard", 68 11 055 "with

exhalation non-return valve") from the packaging.

For reasons of hygiene, leave the protective wrapping around the mouth

contact area until the mouthpiece is firmly attached to the instrument.

2. Attach the mouthpiece at an angle to the mouthpiece receptacle and press

it into the receptacle.

The fluted markings (press-on surface) on the mouthpiece face upwards

while this is done.

The mouthpiece audibly snaps into place (see Page 2).

3. Remove all packaging.

Keep the button pressed for approx.1 second until the startup screen is

displayed. An optional self-test is carried out. The following is shown on the

display for approx. 4 seconds:

READY

The instrument is ready to measure.

4. Blow evenly and without interruptions into the mouthpiece. A progress bar

is displayed. An adequate breath flow is signaled by a continuous tone.

5. Without any further action from the user side. the device takes automatically

a test sample at the end of the breath of the test subject.

6. When an adequate breath sample is provided, the continuous tone stops

with an audible click.The test subject can stop blowing.

The test result is displayed with the date and time after a few seconds

(depending on the device temperature and the measured concentration).

In case of a negative alcohol test, 0,00 will be displayed. In case of a positive

alcohol test, the measured alcohol level will be displayed.

Performing another measurement:

Use

To prepare a new measurement, press the button.

After the sensor’s recovery time (see "Technical data" on Page 16) READY

is displayed and the device is ready to use again.

4.4 Carrying out a manual breath sample (optional)

If the test subject cannot provide the required minimum volume, the sampling

can be triggered manually.

Carrying out a manual breath sample:

1. Follow steps of the automatic breath sample.

2. If the progress bar is displayed after starting the breath sample, tap the

button.

In the results display, MANUAL is also displayed.

4.5 Carrying out a passive breath sample (optional)

During passive sampling, the sampling is manually initiated by the instrument

user. Possible applications include the testing of ambient air or the breath of

persons for the presence of alcohol.

Carrying out passive sampling:

1. Keep the button pressed for approx. 1 second until the startup screen

appears.

2. Hold the instrument, which is ready to measure, into the air to be analyzed

without a mouthpiece.

3. Tap the button to initiate the measurement.

In the results display, PASSIVE is also displayed. If no alcohol is detected, the

No Alcohol will be displayed and the LED will be green. In case alcohol is

detected, Alcohol will be displayed and the LED will be red.

4.6 Removing the mouthpiece

1. Push the mouthpiece up and out of the mouthpiece receptacle (see

illustration on Page 2).

2. Dispose of the mouthpiece in accordance with local regulations.

Do not reuse a mouthpiece.

4.7 Menu control

Accessing the menu:

Press the button.

Use

Navigating in the menu or changing settings:

Press the or button.

Confirm the selected feature/input with the button.

Exiting the menu:

In the sub-menu, select the Back menu item.

In the main menu, select the Measuring menu item.

4.8 Menu items

The following table provides an overview of the menu options and how to use

them:

Menu option Description Interaction instruction

Measuring Option to leave the menu

and to go back to the READY

screen to perform a test.

Hold the button for

2 seconds to leave the

menu.

Bluetooth®

(optinal)

Menu option to switch

Bluetooth®on or off.

Select Bluetooth®On or

Off with the or

button.

Confirm with the

button.

The device is set up for connection to an app via

Bluetooth®.

An active Bluetooth®connection is displayed by a

corresponding symbol in the display.

Bluetooth®must not be selected in aircraft.

Printer Menu option to set a default

printer and to switch the

function on and off.

Select the printer using

the and buttons.

Confirm with the

button.

Altri manuali per Alcotest 6000

Indice

Lingue:

Altri manuali Dräger Apparecchiature di prova

Dräger

Dräger Alcotest 5510 Manuale utente

Dräger

Dräger 2500 Manuale utente

Dräger

Dräger Alcotest 7510 Manuale utente

Dräger

Dräger Interlock XT Manuale utente

Dräger

Dräger Alcotest 9510 Manuale utente

Dräger

Dräger DrugCheck 3000 Manuale utente

Dräger

Dräger Alcotest 7510 Manuale di istruzioni

Dräger

Dräger Alcotest 7000 med Manuale utente

Dräger

Dräger Aerotest 5000 Manuale utente

Dräger

Dräger Alcotest 6820 Manuale utente

Dräger

Dräger Alcotest 5000 Manuale utente

Dräger

Dräger DLE-Set Manuale utente

Dräger

Dräger Alcotest 7510 Manuale utente

Dräger

Dräger Alcotest 7000 Manuale utente

Dräger

Dräger Alcotest 6810 med Manuale utente

Dräger

Dräger DrugTest 5000 STK Manuale utente

Dräger

Dräger Interlock 5 00 Series Manuale utente

Dräger

Dräger Interlock 7000 Manuale utente

Dräger

Dräger Alcotest 9510 Standard IR Manuale utente

Dräger

Dräger Alcotest 6000 Manuale utente

Dräger

Dräger Alcotest 7000 Manuale utente

Dräger

Dräger Interlock Demo-Unit Manuale utente

Dräger

Dräger Alcotest 5000 Manuale utente

Dräger

Dräger Interlock 7500 Manuale utente

Manuali Apparecchiature di prova popolari di altre marche

SMART

SMART KANAAD SBT XTREME 3G Series Manuale utente

Agilent Technologies

Agilent Technologies BERT Serial Manuale utente

Agilent Technologies

Agilent Technologies N3280A Manuale utente

Vernier

Vernier Go Direct Voltage Manuale utente

Lifeloc

Lifeloc R.A.D.A.R. Manuale utente

Fluke

Fluke T5-600 Istruzioni per l'uso e l'installazione

Mercury

Mercury TSL01 Manuale utente

MAHA

MAHA MBT Series Manuale utente

Fuji Electric

Fuji Electric P-61 Manuale utente

ETC

ETC SealerAtor Manuale utente

Skyfine

Skyfine ETHYWAY V2 Manuale utente

Appion

Appion G5 Twin Manuale utente

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuale utente

BW Technologies

BW Technologies MicroDock II Manuale utente

Sun Nuclear

Sun Nuclear 1027 Manuale utente

Biomark

Biomark HPR LITE READER Manuale utente

Hioki

Hioki 3169-20 Manuale utente

Ashcroft

Ashcroft ATE-100 Manuale utente