Dremel 3D20 Idea Builder Manuale utente

Read the Dremel 3D20 manual and

these instructions. Failure to comply

with the warnings and instructions may result in fire,

equipment damage, property damage, or personal

injury.

Always unplug Dremel 3D20 from its power before per-

forming any service procedures. Failure to do so may

re-sult in personal injury and equipment damage.

se only Dremel approved materials and components.

Use of object materials, or 3D objects other than Dremel

approved object materials and genuine Dremel

components may void warranty.

Repairs on the Dremel 3D20 may require the use of special

tools (pulling devices and bearing press). Authorized repair

centers have trained repair technicians and equipment

necessary to perform these repairs.

For the location of the repair center near you, look on

our web site at www.Dremel3D.com and follow the link

for ‘Support’.

Unclogging the 3D20

SERVICE INSTR CTIONS

Tools Required:

• Scissors

• 2,5 mm Allen key

•Needle Nose Pliers

Step 1: Remove the top cover

Do not touch the extruder tip or heated build platform during Dremel 3D20 operation or until it

has cooled down to at least 60oC (140oF). Contact with the extruder tip or build platform during or

after operation before tip and build platform has cooled may result in personal injury.

Please click here for Video Tutorial

Step 2: Unload filament from the extruder.

Step 3: Power off then unplug the power

cord from the Dremel 3D Idea Builder.

2

Step 4: Move, by hand, the extruder to

the center of the Idea Builder.

Step 5: Open the front door, then using

the allen wrench, loosen the two screws

on the front fan.

Step 6: Remove the fan exposing the

drive gear.

Step 7: Remove the clogged filament

with a needle nose pliers. Note: Make

sure to remove all remnants of the

clogged filament and discard

appropriately. Any remaining filament

may cause the printer to not work

properly.

Step 8: Replace the stepper motor

and fan. Tighten the 2 fan screws in

place. Note: Screws should be hand

tightened. Do not over tighten or you

may damage the extruder fan.

Altri manuali per 3D20 Idea Builder

11

Indice

Altri manuali Dremel Stampante 3D

Dremel

Dremel 3D40 Idea Builder Manuale utente

Dremel

Dremel 3D20 Idea Builder Manuale utente

Dremel

Dremel DigiLab 3D45 Guida rapida

Dremel

Dremel DigiLab 3D45 Istruzioni operative

Dremel

Dremel 3D20 Idea Builder Manuale utente

Dremel

Dremel 3D20 Idea Builder Manuale utente

Dremel

Dremel DigiLab 3D45 Manuale utente

Dremel

Dremel DigiLab 3D45 Istruzioni per il montaggio

Dremel

Dremel DigiLab 3D45 Manuale utente

Dremel

Dremel 3D40 Idea Builder Manuale utente

Dremel

Dremel 3D20 Idea Builder Manuale utente

Dremel

Dremel 3D40-EDU Istruzioni per il montaggio

Dremel

Dremel 3D40 Idea Builder Guida rapida

Dremel

Dremel DigiLab 3D45 Manuale utente

Dremel

Dremel Idea Builder 3D20-01 Manuale utente

Dremel

Dremel DigiLab 3D40 FLEX Manuale utente

Dremel

Dremel 3D20 Idea Builder Manuale utente

Dremel

Dremel DigiLab 3D45 Manuale utente

Dremel

Dremel DigiLab 3D45 Manuale utente

Dremel

Dremel 3D40 Idea Builder Manuale utente

Dremel

Dremel 3D20 Idea Builder Manuale utente

Dremel

Dremel 3D40 FLEX Istruzioni per il montaggio

Dremel

Dremel 3D20 Idea Builder Manuale utente

Dremel

Dremel 3D40 Idea Builder Istruzioni operative

Manuali Stampante 3D popolari di altre marche

Ultimaker

Ultimaker S5 Material Station Manuale utente

EcubMaker

EcubMaker TOYDIY Manuale utente

AnyCubic

AnyCubic Kossel Plus Manuale utente

ReDeTec

ReDeTec ProtoCycler Manuale utente

Kywoo3D

Kywoo3D Tycoon IDEX Manuale utente

CraftBot

CraftBot PLUS PRO Manuale utente

3DGence

3DGence INDUSTRY F340 Manuale utente

HP

HP Jet Fusion 4200 Istruzioni operative

Rokit

Rokit AEP Series Manuale utente

AnkerMake

AnkerMake M5 Manuale utente

DIYElectronics

DIYElectronics PRUSA I3 Istruzioni per il montaggio

Ackuretta

Ackuretta FreeShape 120 Manuale utente

LONGER

LONGER LK5Pro Manuale utente

Stratasys

Stratasys J850 Manuale utente

MakerBot

MakerBot Replicator Manuale utente

Stratasys

Stratasys FDM Vantage Series Manuale utente

ZYYX

ZYYX Pro II Manuale utente

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guida utente