Eaton ELC-CODNETM Manuale utente

ELC-CODNETM Effective December 2010

Users Manual

ELC-CODNETM

MN05006002E FormoreInformationvisit:www.eaton.com 1

Introduction

3This is an OPEN-TYPE device and therefore should be installed in an enclosure free of airborne

dust, excessive humidity, shock and vibration. The enclosure should prevent non-maintenance

staff from operating the device (e.g. key or specific tools are required to open the enclosure) to

avoid potential equipment damage or personal injury. DO NOT touch any terminal when the power

is switched on.

3Please read this manual carefully and follow the instructions to avoid damage to the product or

personal injury.

Table of Contents

1Introduction............................................................................................................................2

2Specification ..........................................................................................................................2

3Product Profile and Outline..................................................................................................3

4Installation and Wiring..........................................................................................................4

5Input and Output Image mapping........................................................................................6

6Application.............................................................................................................................7

6.1 Using the CODNETM module as a polling master.....................................................7

6.2 Using Explicit Messages in the Application Program.............................................15

Microsoft® and Windows Internet Explorer® are the registered trade mark or trade mark

of Microsoft Corporation in the United States and other countries.

Java® is the registered trade mark or trade mark of Sun Microsystems, Inc. in the United

States or other countries.

The companies and products mentioned in this operation manual can be the trade mark

possessed by the owner of that trade mark right.

ELC-CODNETM

2 For more Information visit: www.eaton.com MN05006002E

1 Introduction

DeviceNet is an international, open and vendor- independent communication protocol widely

applied in industrial and process automation.

The ELC-CODNETM provides the ability for an ELC-PV processor to exchange data on a

DeviceNet network. The ELC-CODNETM can act both as a DeviceNet master and as a

DeviceNet slave.

Features

zSupports DeviceNet master and slave modes

zAs a master the CODNETM supports polled, bit-strobe, change of state and cyclic I/O

messaging.

zProvides continuous I/O scanning of slave devices

zProvides explicit messages triggered by ELC program

zSupport EDS file configure in ELCSoft software

zConnection size is flexible from 1 to 380 bytes in the input and output area

2 Specification

DeviceNet Physical and Transport layers

Interface Removable connector (5.08mm)

Transmission method CAN

Transmission cable 2-wire twisted shielded cable with 2-wire bus power cable and

drain

Electrical isolation 500VDC

Current draw from

DeviceNet supply Less than 50mA. All other power provided from the ELC supply

Message type I/O polled, bit-strobe, change of state/cyclic

Baud rates 125kbps, 250kbps, 500kbps

Product code 64

Product type 12

Vendor ID Eaton

Environmental Specifications and agency certifications

Noise immunity

ESD (IEC 61131-2, IEC 61000-4-2): 8KV Air Discharge

EFT (IEC 61131-2, IEC 61000-4-4): Power Line: 2KV, Digital I/O:

1KV,

Analog & communication I/O: 1KV

Damped-Oscillatory Wave: Power Line: 1KV, Digital I/O: 1KV

RS (IEC 61131-2, IEC 61000-4-3): 26MHz ~ 1GHz, 10V/m

Environment Operation: 0ºC ~ 55ºC (temperature); 50 ~ 95% (humidity);

pollution degree 2

Storage: -25 ºC ~ 70ºC (temperature); 5 ~ 95% (humidity)

ELC-CODNETM

MN05006002E FormoreInformationvisit:www.eaton.com 3

Vibration/shock

resistance Standard: IEC61131-2、IEC 68-2-6 (TEST Fc)/IEC61131-2 & IEC

68-2-27 (TEST Ea)

Certificates

3 Product Profile and Outline

IN0

SHLD

GND

CAN-

ERR

NODE ADDRESS

DR 2

DR 1

DR 0

x16

POWER

RUN

5151

1. Extension port 2. Power, MS, NS LED

3. DIN rail clip 4. Digital indicator

5. Extension clip 6. Address switch

7. Function switch 8. DeviceNet connection port

Dimension

60 33.1

IN0

SHLD

GND

CAN-

ELC-CODNETM

ERR

NODE ADDRESS

DR 2

DR 1

DR 0

x16

POWER

RUN

90 63.4

Unit: mm

ELC-CODNETM

4 For more Information visit: www.eaton.com MN05006002E

4 Installation and Wiring

Installing ELC-CODNETM With an ELC Controller

1. Adjust the extension clip on the left side of the controller.

2. Connect the extension port of the controller with ELC-CODNETM as the figure below.

3. Fasten the extension clip.

x10

DR 1

DR 0

IN 1

IN 0

POWER

PIN Definition Of DeviceNet Connection Port

PIN Signal Color Content

1 V- Black 0 VDC

2 CAN_L Blue Signal-

3 Drain - Shield

4 CAN_H White Signal+

5 V+ Red 24 VDC

MAC ID Setting

Switch setting Content

0…63 Valid DeviceNet MAC ID setting

Others Invalid DeviceNet MAC ID setting

Function Switch Setting

DR1 DR0 Baud rate

OFF OFF 125kbps

OFF ON 250kbps

ON OFF 500kbps

Hold the I/O data

ON Hold the input and output buffer data when

unit losses DeviceNet communication

IN0

OFF Clear the input and output buffer data when

unit losses DeviceNet communication.

IN1 Reserved

ELC-CODNETM

MN05006002E FormoreInformationvisit:www.eaton.com 5

Connecting the ELC-CODNETM Scanner With Slave Devices

POWER

x10

DR 0

DR 1

x10

IN 1

IN 0

POWER

x10

IN 0

IN 1

DR1

DR0

RUN

STOP

ERROR

BAT.LOW

POWER

RUN

x10

RS-485

RS-232

ELC-CODENTM

ELC-PC28NNDR/T

ELC-CODENT

ELC-PH12NNDR/T

ELC-PS01

DeviceNetAdapter

C Motor Driver

Cable Length and Baud Rates

The maximum cable length in a segment depends on the transmission speed. DeviceNet

communicates at speeds from 125kbps to 500kbps over distances from 100 to 500 meters.

Baud rates (bps) 125k 250k 500k

Length (m) 500 250 100

If you need more information on installing a DeviceNet network, see “DeviceNet Planning

and Installation Manual” available from ODVA.org.

ELC-CODNETM

6 For more Information visit: www.eaton.com MN05006002E

5 Input and Output Image mapping

Data exchange between ELC-CODNETM Scanner and the ELC processor

When the ELC-CODNETM scanner is connected to the ELC processor, it will map to a

section of the ELC processor data area (D registers).

Mapped d registers

Index of

ELC-CODNETM

scanner Output image table Input image table

1 D6250 ~ d6497 D6000 ~ d6247

2 D6750 ~ d6997 D6500 ~ d6747

3 D7250 ~ d7497 D7000 ~ d7247

4 D7750 ~ d7997 D7500 ~ d7747

5 D8250 ~ d8497 D8000 ~ d8247

6 D8750 ~ d8997 D8500 ~ d8747

7 D9250 ~ d9497 D9000 ~ d9247

8 D9750 ~ d9997 D9500 ~ d9747

The index is the relative position of the ELC-CODNETM module to the left side of the ELC

processor. The 1st module left of the ELC processor is index number 1. The next module to

the left is number 2. The others are indexed as 3, 4, and so on.

Input and Output Image Table contents

The table below shows the contents of the register map for an ELC-CODNETM with

index=1

Output image

D register Image mapping Length

D6250 ~ D6281 Explicit message program request 32 words

D6282 ~ D6285 Bit-strobe command 4 words

D6286 Reserved 1 word

D6287 ~ D6476 DeviceNet output data 190 words

D6477 ~ D6497 Reserved for other function (do not use these

devices in user program) 21 words

Input image

D register Image mapping Length

D6000 ~ D6031 Explicit message program response 32 words

D6032 ~ D6035 Scan list node status indication 4 words

D6036 Scanner module status indication 1 word

D6037 ~ D6226 DeviceNet input data 190 words

D6227 ~ D6247 Reserved for other function (do not use these

devices in user program) 21 words

ELC-CODNETM

MN05006002E FormoreInformationvisit:www.eaton.com 7

6 Application

6.1 Using the CODNETM module as a polling master

The ELC-CODNETM module is a polling master on DeviceNet that also supports slave

mode at the same time. The CODNETM module is configured using the DNET CONFIG tool

located in ELCSoft. Click the icon shown below to run DNET CONFIG.

When the DNET CONFIG icon is clicked, the following screen will open:

ELC-CODNETM

8 For more Information visit: www.eaton.com MN05006002E

To go online with the DeviceNet network, the computer must be connected to the ELC

controller which in turn is connected to the CODNETM module via the controller’s left-side

bus. In the DNET CONFIG software, select Setup, followed by Communication Setting, then

System Channel. The following screen will open:

These are the default communication parameters. Be sure to select the correct COM port

on your computer that is being used to connect to the ELC controller with the

ELC-CBPCELC3 programming cable. When the cable is connected and the interface

parameters are set, click the Network drop down menu and select Online and the following

screen will open:

In this case there is only one master communication module connected to the left-side bus

Indice

Altri manuali Eaton Unità di controllo

Eaton

Eaton Moeller SmartWire-Darwin EU5C-SWD-DP Manuale

Eaton

Eaton Cutler-Hammer PanelMate ePro PS Series Manuale utente

Eaton

Eaton CI-PKZ01 Series Manuale

Eaton

Eaton PXR-PCAM Manuale

Eaton

Eaton COOPER POWER SERIES Manuale del proprietario

Eaton

Eaton PowerXL DX-NET-ETHERCAT-2 Manuale

Eaton

Eaton Powerware 9125 Manuale utente

Eaton

Eaton ELC-PC12NNDR Manuale utente

Eaton

Eaton DILM12-XMSM Manuale

Eaton

Eaton RFAPM Manuale utente

Eaton

Eaton MSFI-80A Manuale

Eaton

Eaton Durant Eclipse Series Manuale utente

Eaton

Eaton i-on30R Manuale utente

Eaton

Eaton Ampgard AR Manuale utente

Eaton

Eaton ELC-COENETM Manuale utente

Eaton

Eaton Char-Lynn 5 Series Manuale utente

Eaton

Eaton Crouse-hinds series Manuale utente

Eaton

Eaton DX-NET-BACNETMSTP Manuale

Eaton

Eaton MEMSHIELD 4 Manuale utente

Eaton

Eaton Cuttler-Hammer Pow-R-Command 100 Manuale

Eaton

Eaton EC4E-221-6D4T1 Manuale utente

Eaton

Eaton NZM XMC Series Manuale utente

Eaton

Eaton ELC-MC01 Manuale utente

Eaton

Eaton COOPER POWER SERIES Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente

Flyron

Flyron FN-BC04 Manuale utente