Eaton 415U-2 Manuale utente

415U-2 wireless mesh networking I/O and gateway

installation guide

Statutory requirements

FCC: This device complies with

Part15.247 of the FCC Rules.

Operation is subject to the

following two conditions:

• This device may not cause

harmful interference.

• This device must accept any

interference received, including

interference that may cause

undesired operation.

FCC: Unlicensed operation limits

the radio power. High gain aerials

may only be used to compensate

for cable losses.

mWARNING - EXPLOSION

HAZARD

Do not disconnect the device while the

circuit is live unless the area is known

to be non-hazardous.

NOTE

The 415U-2 module ships from

the factory in configuration mode.

The radio locale, frequency, and RF

power need to be configured using

the embedded web pages before

use.

Antenna installation

Use Figure 1 as a guide for installing an antenna and attaching it

to the module.

Figure 1. Antenna installation

Earth Stake

For maximum

range, install

above local

obstructions.

Earth Conductor

at least 5 AWG

(16 mm2)

Wavelength:

360MHz = 32.7” (83cm)

512MHz = 22.8” (58cm)

Weatherproof

Connections

(recommended:

3M™23 self-

bonding tape)

Mast

Coaxial Cable

GND

at least 11 AWG (4 mm2)

Stress

Relief

Loop

Antenna*

GND

Surge Arrestor

(recommended)

415U-2

Provide good ground

connection to mast,

module, and surge

arrestor.

If ground conditions

are poor, use more

than one stake.

1 Wavelength

(minimum)

Connecting to the module for conﬁguration

The default settings for the 415U-2 are as follows:

• IP Address: 192.168.0.1XX, where “XX” is the last two digits

of the serial number shown on the printed label on the side of

the module

• Subnet Mask: 255.255.255.0

• Default Gateway: 192.168.0.1

• Username: user

• Password: user

1. Connect a straight-through Ethernet cable between the

module’s Ethernet port and a PC.

2. Open Internet Explorer on the PC.

3. Type “http://” followed by the IP address of the module and

press Enter.

Instruction Leaﬂet IL032043EN Effective April 2015

All manuals and user guides at all-guides.com

all-guides.com

Eaton

1000 Eaton Boulevard

Cleveland, OH 44122

United States

Eaton.com

Eaton’s wireless business

www.eaton.com/wireless

Eaton is a registered trademark.

All other trademarks are property

of their respective owners.

415U-2 wireless mesh networking I/O and gateway installation guide

Printed in USA

Publication No. IL032043EN

April 2015

Instruction Leaﬂet IL032043EN

Effective July 2015

NOTE

All connections must be SELV <50Vac and <120Vdc.

The following illustrations show the ports on the 415U2.

PWR

232

485

LED Indicator

Lights

I/O Connectors

RJ-45 Ethernet Port

(connects to hub or switch)

USB Port RS-232 Port

ETHERNET USB RS232 SUPPLY

GND BAT SUP SUP

B A

Power supply wiring

The ground (GND) and “SUP–“

terminals are connected

internally to the ground terminal.

Connect the screw terminal on

the end plate to ground for surge

protection.

Expanson I/O power and RS-485 serial connection

An on-board RS-485

terminating resistor provides

line attenuation for long runs.

Place terminating resisters

at each end of the RS-485

cable.

Conﬁguration switches

Use the DIP switches in the

side access panel to select

analog input voltage and

current, external boot, and

default configuration settings.

DIP DESCRIPTION

1 AI3 current/voltage

2 AI3 current/voltage

3 AI4 current/voltage

4 AI4 current/voltage

5 Unused

6 Enables default configuration

Input and output connections

The digital input/output channels can be wired as inputs or outputs.

Digital input Digital output

Transistor

Switch

Device

Voltage-free Contact

TTL CMOS

Output

D1 D3 D4 D5 D6 D7 D8

GND

+24V

DC Load

+ –

D1 D3 D4 D5 D6 D7 D8 GND

+24V

Differential current inputs (Al1, Al2) Single-ended current input (Al3, Al4)

Loop-Powered

Sensor

Exernally

Powered

Sensor

Power Supply

D8 GND +24V

AI1

_AI2

AI2

_AI3 AI4

AO1

AO2

+GND

+24V

Loop-Powered

Sensor

Power Supply

Externally

Powered

Sensor

DIP Switch Setting

for Current IP

GND +24V

AI1

_AI2

AI2

_AI3 AI4

AO1

AO2

+GND +24V

1 2 3 4 5 6

Analog output Single-ended voltage input

PLC

COM

AI1 AI1

_AI2

AI2

_AI3 AI4

AO1

AO2

GND +24V

0–25V

Sensor

0–5 Vdc

Sensor

+24V

AI1

_AI2

AI2

_AI3 AI4

AO1

AO2

GND +24V

DIP Switch Setting

for Voltage IP

1 2 3 4 5 6

ETHERNET USB

RS232

B A

115S-xx 115S-xx

RS-485

B A

B A B A

-+-+

USB RS232 SUPPLY

GND BAT SUP SUP

15-30 Vdc

Supply

3A Fuse

Optional

10.8–15 Vdc

Lead Acid

Battery

–

USB Host

Factory Boot

Switch

%QPʙIWTCVKQPSwitches

Side

Access

Panel

All manuals and user guides at all-guides.com

Altri manuali Eaton Portale

Eaton

Eaton EU5C-SWD-EIP-MODTCP Manuale utente

Eaton

Eaton SmartWire-DT Manuale utente

Eaton

Eaton Power Xpert Gateway 900 Manuale utente

Eaton

Eaton Power Xpert Gateway 900 Manuale utente

Eaton

Eaton 415U-2 Manuale utente

Eaton

Eaton LOYTEC LGATE-902 Manuale utente

Eaton

Eaton XN-GWBR Series Manuale utente

Eaton

Eaton LumenSafe Manuale utente

Eaton

Eaton EASY223-SWIRE Manuale

Eaton

Eaton PXG950-4G Manuale utente

Eaton

Eaton Moeller SmartWire-Darwin Series Manuale utente

Eaton

Eaton ELPRO 415U Manuale utente

Eaton

Eaton Power Xpert Gateway Minislot Manuale di programmazione

Eaton

Eaton Power Xpert Meter 2000 Manuale utente

Eaton

Eaton INDGW-M2 Manuale utente

Eaton

Eaton SmartWire-DT EU5C-SWD-DP Manuale utente

Eaton

Eaton PXG600E Guida

Eaton

Eaton 415U-2-C Manuale

Eaton

Eaton INDGW-X2 Manuale utente

Eaton

Eaton EG2-NA Manuale utente

Eaton

Eaton POW-R-COMMAND 1000 Manuale utente

Eaton

Eaton ProtoAir FPA-W34 Guida utente

Eaton

Eaton Power Xpert Gateway 900 Manuale di istruzioni

Eaton

Eaton Power Xpert Gateway 200E Guida

Manuali Portale popolari di altre marche

LST

LST M500RFE-AS Manuale utente

Kinnex

Kinnex Media Gateway Manuale utente

2N Telekomunikace

2N Telekomunikace 2N StarGate Manuale utente

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuale utente

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manuale utente

Telsey

Telsey CPVA 500 - SIP Manuale utente

RTA

RTA 460A-NNA4 Scheda tecnica

Shaw

Shaw Gateway HDPVR Manuale utente

ABB

ABB VSN900 Guida rapida

Commander

Commander Pulse Manuale utente

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manuale utente

NETGEAR

NETGEAR C6300BD Manuale utente

Amit

Amit CDW531AM Manuale utente

HMS

HMS Netbiter EasyConnect EC150 Manuale utente

Huawei

Huawei EchoLife HG620 Manuale utente

AT&T

AT&T U-verse 3801 Manuale per l'uso e la cura

Logic IO

Logic IO RTCU MX2 turbo Manuale utente

Suttle

Suttle MediaMAX MXM-521 Manuale utente