Eaton EG-2 Manuale utente

EG-2

Ethernet Gateway

Installation guide

Eaton Lighting Systems iLight Product Series - EG-2 9850-000224-02 2

Contents

Introduction 3

Basic Schematic 3

Installation 3

Product Overview 4

Connecting the Supply 5

iCAN Network Connections 5

Set Up Instructions 6

Conﬁguration 6

Setting the IP address 6-7

Eaton Lighting Systems iLight Product Series - EG-2 9850-000224-02 3

Introduction

The Ethernet Gateway 2 provides

connection between an iLight CAN

network and an Ethernet LAN. This allows

a user to control and conﬁgure the iLight

system using iCANsoft on a LAN network

PC rather than by connecting directly into

the network.

The EG2 also facilitates connection to the

internet when installed behind a ﬁrewall.

This then enables remote connection for

controlling, programming and obtaining

diagnostics of the lighting control system.

The EG2 also functions as a smartphone

device host allowing control and

programming of the iLight network. Apps

are available free of charge for Android

and Apple devices.

Facilities are provided to allow a BMS or

smart home system to interact with the

iLight network. This is achieved by simple

character strings communicated via a UDP

or TCP connection.

Basic Schematic

Installation

Location

The EG2 should be installed in a dry ventilated

location, where ambient conditions are main-

tained within the requirements of the unit. The

unit has ventilation slots on its sides to allow

convection cooling and in no circumstances

should these be blocked.

Mounting

Always mount in well ventilated location Allow

50mm (2”) above and below the unit if trunking

with a depth greater than 50mm (2”) is used.

Ambient atmosphere requirements

Temperature: +2°C to +40°C (+36°F to +104°F)

Humidity: 5% to 95% non-condensing

IP Rating: IP20

Weight:

0.25Kg (0.55 lbs)

Dimensions

Eaton Lighting Systems iLight Product Series - EG-2 9850-000224-02 4

Ethernet LINK

LED on indicates the

link is connected at

100Mb

LED off indicates the

link is connected at

10Mb

Ethernet DATA

LED on indicates that

the Ethernet link is

established

LED flashes off briefly

when Ethernet traffic is

present

SD card DATA

LED flashing indicates

memory card is being

accessed

SD card INPUT

Indicates SD Memory

card location

iCAN DATA

Red flashing LED indicates

traffic being sent and/or

received

Red LED on indicates a

CANbus error

iCAN IDENT

Switch that causes the EG2 to

send a message on the CAN

BUS to identify itself

iCAN status

Green flashing LED indicates

normal operation

Product Overview

The label on the enclosure identifies the position of the status LEDS, switches & connectors.

iCAN Network

For connection

see P6 for wiring

details

TIMECLOCK

Set through iLight

programming

software.

LED on when

timeclock active

RESET

Switch that resets

the device. Only

press this on

direct instruction

from Eaton

to avoid data

corruption

Ethernet INPUT

Indicates Ethernet

connector location

POWER

The Green Power

LED will double flash

continuously while

EG2 is on.

CAN Termination

End of network

termination jumper.

Eaton Lighting Systems iLight Product Series - EG-2 9850-000224-02 5

Connecting the Supply

Power is to be supplied to the EG2 via an external

regulated power supply in the range of 9-36VDC

0.3A

Eaton are able to provide a recommended power

supply if required.

Catalogue Number: PSU-15-DIN (15VDC 0.67A)

A removable 2 way connector screw terminal

plug is provided for the connection of the power

supply. Terminal sizes: 2 x 1.5mm2

iCAN Network Connections

A removable 5 way connector screw terminal

plug is provided for the connection of iCAN

network cables. Terminal sizes: 5 x 1.5mm²

IMPORTANT NOTE: Connecting a mains

potential cable to the iCAN Network terminals

is likley to damage the unit and others

connected, and invalidate warranty.

Function Cable Colours

+12Vdc Red

CAN H Blue

Shield Silver

CAN L White

0V Black

CAN-L

SHIELD

CAN-H

+12V

iCAN devices are ‘daisy-chained’ on the

network. Spurs from the Network are not

permitted and will result in communications

problems. Devices on an iCAN network can be

wired in any order. Termination is required at

both ends of the network.

Network Termination

T - Indicates where a termination is required.

The EG-2 has built-in network termination. If

the EG-2 is at the end of the network, ensure

the CAN TERMINATION jumper is ﬁtted in the

Termination On position.

Termination On

Termination Off

iCAN

Device

iCAN

Device

EG2

Eaton Lighting Systems iLight Product Series - EG-2 9850-000224-02 6

Set Up Instructions

iCAN Network

Connect the EG2 to the iCAN network using the network connector. If the EG2 is at the end of a

network set the Term link to ON otherwise set to the OFF position

Ethernet

Ethernet connection by RJ45 (568B). This should be connected to either an Ethernet Switch or to

a Wireless Router.

Configuration

iCAN Device Number

The EG2 is supplied with a iCAN Network Device number with Segment number 255 and a

node number in the range 1-255. Both Segment and Node number can be changed using iLight

programming software.

Factory Default IP settings

IP Address: 192.168.0.100

Subnet mask: 255.255.255.0

Gateway: 192.168.0.254

DHCP: Off

Note: The EG2 default settings are to use a ﬁxed IP address of 192.168.0.100. Any device used to

communicate with the EG2 will need to be located within the 192.168.0.x subnet.

Power up

The EG2 takes approximately 60 seconds to be ready for use once power is applied.

Wait for the Green CAN LED to ﬂash slowly.

The Green Power LED will double ﬂash continuously while EG2 is on.

Setting the IP address

The factory set IP Address can be changed using the iCAN network connection or using a

computer connected directly to the Ethernet port.

Changing with iCAN Network

Connect to the iCAN network a computer running iLight programming software using an iLight PC

Node. Search the network and load the EG2 into the software.

Go the Ethernet tab. Either the Default settings can be applied or other settings can be applied.

Select OK or Apply to download the changes to the EG2.

Eaton Lighting Systems iLight Product Series - EG-2 9850-000224-02 7

Change IP address via the Ethernet port

EG2 is supplied from the factory without DHCP enabled; therefore, it is necessary that the

Ethernet port of the PC is set to the correct IP Address and Subnet Mask. For details of setting

the IP address of your computer consult information on line. This will depend on your Operating

System.

Example

IP Address: 192.168.0.99

Subnet mask: 255.255.255.0

Gateway: 192.168.0.254

To connect the EG2 directly to the PC, it may be necessary to use a Crossover Cable, however,

most modern computers are able to connect directly to another Ethernet device without a

crossover cable.

The Ethernet port of your computer will need to conﬁgured to a compatible IP address.

Open iLight programming software. It will be required to set the software to communicate using

the Ethernet Port.

This is done by selecting from the Tool bar Tools>Options>Network.

Select Ethernet Gateway and change the IP address to 192.168.0.100. Also ensure the ‘Use

Select OK to conﬁrm and set the address.

The software can now be used to conﬁgure

any items connected on the network.

Set the IP address of the EG2 as described

in section opposte. The new IP address will

become valid when the EG2 is reset or power

to the device is removed and re-instated.

Reset to factory defaults

Factory defaults may be reset by the following procedure:

Remove power from the board.

Press the CAN ID button and reapply power. Keep the button pressed until the CAN LED ﬂashes

then stays on. At this point the Ethernet settings will have been restored to defaults.

After setting to factory defaults, the IP address of the device will revert to 192.168.0.100

Document: EG-2 9850-000224-02

Eaton Lighting Systems

Usk House, Lakeside, Llantarnam Park, Cwmbran, NP44 3HD, UK

T: +44 (0)1923 495495 F: +44 (0)1923 228796

E: [email protected] EatonLightingSystems.com

iLight Technical Support

Tel: +44 (0)844 324 9100 (available Mon-Fri 9am-5pm GMT)

Email: Tec[email protected]

Web: www.iLight.co.uk

All products manufactured by Eaton Lighting Systems and identiﬁed with the iLight product series

mark are warranted to be free from defects in material and workmanship and shall conform to and

perform in accordance with Seller’s written speciﬁcations.

This warranty will be limited to the repair or replacement, at Seller’s discretion, of any such goods

found to be defective, upon their authorized return to Seller. This limited warranty does not apply

if the goods have been damaged by accident, abuse, misuse, modiﬁcation or misapplication, by

damage during shipment or by improper service.

There are no warranties, which extend beyond the hereinabove-limited warranty,

INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY AND THE

IMPLIED WARRANTY OF FITNESS.

No employee, agent, dealer, or other person is authorised to give any warranties on behalf of the

Seller or to assume for the Seller any other liability in connection with any of its goods except in

writing and signed by the Seller. The Seller makes no representation that the goods comply with

any present or future federal, state or local regulation or ordinance. Compliance is the Buyer’s

responsibility.

The use of the Seller’s goods should be in accordance with the provision of the National Electrical

Code, UL and/or other industry or military standards that are pertinent to the particular end use.

Installation or use not in accordance with these codes and standards could be hazardous.

WARNING HAZARDOUS VOLTAGES

DISCONNECT FROM SUPPLY

BEFORE REMOVING COVERS

NO USER SERVICEABLE PARTS INSIDE

SERVICE BY QUALIFIED PERSONNEL ONLY

WARNING

To reduce the risk of ﬁre or electric shock,

DO NOT expose this device to rain or moisture.

DO NOT energise unless the front cover is in place.

This device must be earthed.

Installation, programming and maintenance must be carried out by qualiﬁed personnel.

Eaton Lighting Systems cannot accept responsibility for repairs or modiﬁcations that are not

competently executed and in accordance with service or upgrade information.

CE compliant to all relevant standards

Indice

Altri manuali Eaton Portale

Eaton

Eaton SWIRE-GW-MB Manuale utente

Eaton

Eaton INDGW-M2 Manuale utente

Eaton

Eaton 415U-2 Manuale utente

Eaton

Eaton EASY209-SE Manuale

Eaton

Eaton LOYTEC LGATE-902 Manuale utente

Eaton

Eaton INDGW-X2 Manuale utente

Eaton

Eaton EASY223-SWIRE Manuale

Eaton

Eaton XNE-GWBR-2ETH-MB Manuale utente

Eaton

Eaton Power Xpert Gateway 900 Manuale utente

Eaton

Eaton Power Xpert Gateway 900 Manuale utente

Eaton

Eaton Power Xpert Meter 2000 Manuale utente

Eaton

Eaton SmartWire-DT EU5C-SWD-DP Manuale utente

Eaton

Eaton XN-GWBR Series Manuale utente

Eaton

Eaton SmartWire-DT Manuale utente

Eaton

Eaton 415U-2-C Manuale

Eaton

Eaton Power Xpert Meter 2000 Manuale utente

Eaton

Eaton Power Xpert Gateway 900 Manuale di istruzioni

Eaton

Eaton EMP Manuale utente

Eaton

Eaton LumenSafe Manuale utente

Eaton

Eaton Moeller SmartWire-Darwin EU5C-SWD-DP Manuale

Eaton

Eaton Power Xpert Gateway Minislot Manuale di programmazione

Eaton

Eaton Moeller SmartWire-Darwin EU5C-SWD-DP Manuale

Eaton

Eaton EG2-NA Manuale utente

Eaton

Eaton PXG600E Guida

Manuali Portale popolari di altre marche

LST

LST M500RFE-AS Manuale utente

Kinnex

Kinnex Media Gateway Manuale utente

2N Telekomunikace

2N Telekomunikace 2N StarGate Manuale utente

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuale utente

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manuale utente

Telsey

Telsey CPVA 500 - SIP Manuale utente

RTA

RTA 460A-NNA4 Scheda tecnica

Shaw

Shaw Gateway HDPVR Manuale utente

ABB

ABB VSN900 Guida rapida

Commander

Commander Pulse Manuale utente

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manuale utente

NETGEAR

NETGEAR C6300BD Manuale utente

Amit

Amit CDW531AM Manuale utente

HMS

HMS Netbiter EasyConnect EC150 Manuale utente

Huawei

Huawei EchoLife HG620 Manuale utente

AT&T

AT&T U-verse 3801 Manuale per l'uso e la cura

Logic IO

Logic IO RTCU MX2 turbo Manuale utente

Suttle

Suttle MediaMAX MXM-521 Manuale utente