EcoxGear SOUNDEXTREME SEI-SETXLED Manuale utente
User Guide
LED Rocker Switch
Remote Control
Model: SEI-SETXLED
2
· Please read this User Guide before installation and use.
· CAUTION: The power input voltage range for your LED Rocker
Switch Remote Control (referred to as Switch) is 9V to 16V. It
is designed to work with a +12V DC battery power supply. If
your vehicle battery power output is not 12V (e.g., 24V, 36V, or
48V), you will need a voltage converter with 12V output (e.g., a
48V-to-12V converter). Connecting the Switch directly to higher
voltages will cause damage to your device and VOID THE
PRODUCT WARRANTY.
· The Switch has a built-in RF remote transmitter that will operate
the LED lights on a wirelessly paired, LEDCast-enabled
SoundExtreme product. This Switch only controls LED light
functions, not audio. It is optimized for the ExtremeController
(a 4-Zone LED Controller by SoundExtreme). To control the
audio functions as well as basic LED controls of SoundExtreme
soundbars, speakers, and radios, please purchase the Audio
Rocker Switch Remote Control. Visit www.soundextreme.us for
more details.
· The Switch fits in a standard Carling rocker switch opening, which
is commonly used in the dashboard of many o-road vehicles,
boats, and golf cars. The Switch panel is waterproof; however, the
housing behind the panel is only splash proof.
· CAUTION: In order to make sure there is no potential damage to
your audio system, unplug or power o your audio equipment until
after all connections are completed.
Important
3
Introduction
Features
The Switch is an all-in-one device providing power and wireless LED
lighting controls to a paired SoundExtreme product.
Remote Turn-On Output
In addition to opperating as a power switch, the Switch also has a
+12V Remote Turn-On signal output, which can be connected to an
ExtremeController’s Remote Turn-On Input. That ExtremeController
can then be automatically turned on or off when you turn the Switch
on or off.
RF Remote Transmitter
The Switch has a built-in RF 433MHz remote transmitter, which
is used to pair with and control an ExtremeController or other
LEDCast-enabled SoundExtreme product. The first time you use the
Switch, you will need to pair it with a product. Once they are paired,
your product will remember your Switch. Next time you power on
your product, your Switch's remote functions will be ready to use.
Lighting Control Concepts
Below are some terms and definitions to help you better
understand the Lighting Control Concepts associated with the
ExtremeController and other LEDCast-enabled SoundExtreme
products. Please refer to the ExtremeController User Guide for
more details.
Zone
A Zone corresponds to all the LED lights that are connected
directly to one physical connection on an LED Lighting Controller
output. When you change a Zone status (on / o, Mode, etc.), the
LEDs connected to that Zone will change accordingly. Depending
on the product the Switch is paired with, the SoundExtreme product
may have 1 to 4 LED lighting Zones.
4
Introduction
Mode
There are 3 LED Mode categories, totaling in 44 Modes supported
by the Switch's RF remote control:
· 8 Color Mode
· 20 Party Mode
· 16 Music Mode
Scene
A Scene is programed via the SoundExtreme Smartphone App.
You can customize each Zone into a Scene (a preset). Setting the
Scenes on the app allows a 1-button press to bring up your desired
custom settings for all of the LED products connected to the LED
Lighting Controller. LEDCast-enabled SoundExtreme products
have 5 Scene settings.
5
Switch Layout
Switch Overview
Power Button
All Zones Button
Mode Button
Brightness Button
Speed Button
Scenes Button
Inputs and Outputs
Power Inputs:
+12V Wire (Red) / GND Wire (Black)
Accessory Outputs:
+12V Wire (Red) / GND Wire (Black)
Remote Turn-On Output
Wire (Dark Blue)
6
Switch Overview
Connectors
Input:
· Power Input: +12V, GND – Connect to your vehicle's +12V battery.
Only connect to a +12V DC power supply.
Outputs:
· Remote Turn-On Output: +12V signal output when the Switch is on.
· Power Outputs: +12V, GND – Connect to a SoundExtreme
product's power input (maximum current not exceeding 20A, 12V).
Button Functions
Power Button
· Press and hold for 3 seconds to turn the Switch on or o.
· When the Switch is on, short-press to turn the button backlights on
or o.
· When the Switch is on, double-click to enable RF Remote Pairing
with a SoundExtreme product.
Brightness Button
· Short-press to cycle through 5 levels of LED brightness for all of
the Zones.
Speed Button
· Short-press to cycle through 5 levels of LED lighting speed for all
of the Zones, while in a Party Mode.
All Zones Button
· Short-press to turn all of the Zones on or o.
7
Switch Overview
Mode Button
· Short-press to cycle through all of the LED lighting Modes for all of
the Zones.
Scenes Button
· Short-press to cycle through 5 predefined LED lighting Scenes.
8
Installation and Wiring
Installing Your Switch Onto Your Vehicle
The Switch is designed to snap into a standard Carling style rocker
switch opening.
· If you already have that style of an opening on your vehicle, you can
simply snap the Switch into place.
· If your vehicle doesn’t already have that style of an opening, you
will need to cut a rectangular hole into your vehicle. Before you cut,
please refer to the dimensions under the Specifications section to
determine the cutout size.
Connecting to an External Speaker
If you want to provide power to and control an external
ExtremeController's or other LEDCast-enabled SoundExtreme
product's power on and o feature, you will need to connect it to the
Switch's Accessory Power Outputs and Remote Turn-On Ouput.
Accessory Power Outputs
Connect the Switch's Accessory Power Outputs (+12V and GND) to
the power inputs on the ExtremeController you want to control.
· Make sure that the Switch's RED +12V Wire is connected to the
ExtremeController's RED Wire and the Switch's BLACK GND Wire
is connected to the ExtremeController's BLACK Wire.
Switch's Accessory
Power Outputs
SoundExtreme Product
Power Inputs
9
Installation and Wiring
Remote Turn-On Output
Switch's Remote
Turn-On Output Wire
SoundExtreme Product
Remote Turn-On Input Wire
Besides the 12V power supply, the Switch has an optional
Remote Turn-On Signal Output to turn on and power o the
ExtremeController or LEDCast-enabled SoundExtreme product
you want to control. The output voltage is 12V.
If your SoundExreme product has a Remote Turn-On Input, follow
the steps below:
1. Connect the Switch's (Dark Blue) Remote Turn-On Output Wire
to the ExtremeController's Remote Turn-On Input. You may need
an extension cable (supplied with the ExtremeController).
2. Once the connections are completed, the ExtremeController will
automatically turn on or o when the Switch is turned on or o.
10
Installation and Wiring
Connecting to 12VDC Power Supply
When you install the Switch to a battery or a voltage regulator on
a golf cart, a boat, a quad bike, a UTV, or another vehicle, you need
to make sure that your vehicle battery or battery pack terminal
voltage is 12VDC. If the battery terminal voltage is not 12V, you will
need a DC–DC converter with output 12V. Connecting the Switch
to a non-12VDC power source will lead to a malfunction or damage
to the Switch.
Recommendation: If you are not familiar with all of the vehicle’s
battery or ignition switch connections, consult your vehicle’s
manual or a technician. Incorrect connections to your vehicle’s
battery or ignition signal terminal may cause damage to your
speaker and your vehicle.
Connect the +12V and GND wires
to the 12VDC power supply.
· Make sure that the RED Wire
is connected to +12V battery’s
positive (+) terminal and the
BLACK Wire is connected to
battery’s negative (-) terminal.
WARNING! Only connect to a 12V
power supply. Do NOT connect to
a 24V, 36V, or 48V power supply.
Connecting the Switch directly to
these higher voltages will cause
damage to the Switch and VOID
THE PRODUCT WARRANTY.
Black Wire Red Wire
Indice
Altri manuali EcoxGear Telecomando
