Edge-Core ES3528MV2 Manuale di programmazione

Management Guide

www.edge-core.com

ES3528MV2

ES3528MV2-DC

28-Port Fast Ethernet

Layer 2 Switch

ANAGEMENT

UIDE

ES3528MV2 FAST ETHERNET SWITCH

Layer 2 Switch

with 24 10/100BASE-TX (RJ-45) Ports,

and 4 Gigabit Combination Ports (RJ-45/SFP)

ES3528MV2-DC FAST ETHERNET SWITCH

Layer 2 Switch with DC power input

with 24 10/100BASE-TX (RJ-45) Ports,

and 4 Gigabit Combination Ports (RJ-45/SFP)

ES3528MV2

ES3528MV2-DC

E112013/ST-R03

– 5 –

ABOUT THIS GUIDE

PURPOSE This guide gives specific information on how to operate and use the

management functions of the switch.

AUDIENCE The guide is intended for use by network administrators who are

responsible for operating and maintaining network equipment;

consequently, it assumes a basic working knowledge of general switch

functions, the Internet Protocol (IP), and Simple Network Management

Protocol (SNMP).

CONVENTIONS The following conventions are used throughout this guide to show

information:

OTE

Emphasizes important information or calls your attention to related

features or instructions.

AUTION

Alerts you to a potential hazard that could cause loss of data, or

damage the system or equipment.

ARNING

Alerts you to a potential hazard that could cause personal injury.

RELATED PUBLICATIONS The following publication details the hardware features of the switch,

including the physical and performance-related characteristics, and how to

install the switch:

The Installation Guide

Also, as part of the switch’s software, there is an online web-based help

that describes all management related features.

BOUT

HIS

UIDE

– 6 –

REVISION HISTORY This section summarizes the changes in each revision of this guide.

NOVEMBER 2013 REVISION

This is the third version of this guide. This guide is valid for software

release v1.4.0.0. It includes the following updates to the manual:

◆Updated parameter ranges under "Configuring The Console Port" on

page 139.

◆Updated parameter ranges under "Configuring Telnet Settings" on

page 140.

◆Updated parameter ranges for “System Reload Configuration” under

"Resetting the System" on page 144.

◆Updated parameter list under "Setting the Time Zone" on page 138.

◆Updated parameter description under "Configuring by Port List" on

page 150.

◆Added “Timeout Mode” to parameter list under "Configuring a Dynamic

Trunk" on page 173.

◆Added the section "Creating CVLAN to SPVLAN Mapping Entries" on

page 211.

◆Added the section "Configuring MAC Address Learning" on page 227.

◆Added the parameters “Action” and “Shutdown Interval” under

"Configuring Loopback Detection" on page 240.

◆Updated thresholds under "Configuring ATC Thresholds and Responses"

on page 267 to use packets per second (pps).

◆Updated parameter description for “Add Rules” under "Configuring a

Class Map" on page 286.

◆Updated para mt er description under "Configuring AAA Authorization"

on page 321.

◆Updated parameter list under "Showing ACL Hardware Counters" on

page 371.

◆Added “Allow Zeros” parameter under "Configuring Global Settings for

ARP Inspection" on page 373.

◆Updated parameter list under "Configuring Port Security" on page 382.

◆Updated parameter list under "DHCP Snooping Configuration" on

page 412.

◆Updated parameter list under "Configuring Ports for DHCP Snooping" on

page 415.

BOUT

HIS

UIDE

– 7 –

◆Updated default settings and added “MED-Location Civic Address”

parameter under "Configuring LLDP Interface Attributes" on page 427.

◆Added the section "Configuring LLDP Interface Civic-Address" on

page 430.

◆Added parameters for Port Details under "Displaying LLDP Remote

Device Information" on page 436.

◆Updated entries in Table 31, "Supported Notification Messages," on

page 456.

◆Added information on changes introduced by ERPSv2 under "Ethernet

Ring Protection Switching" on page 489.

◆Changed description of options for the Interval Level parameter under

"Configuring CFM Maintenance Associations" on page 526.

◆Updated range for the Packet Size parameter under "Using the Ping

Function" on page 561.

◆Added the section "Using the Trace Route Function" on page 563

◆Added description of RA Guard parameters under "Configuring IPv6

Interface Settings" on page 571.

◆Added the section "Specifying A DHCP Client Identifier" on page 595

◆Added the section "Configuring DHCP Relay Option 82" on page 596

◆Added the section "Configuring the PPPoE Intermediate Agent" on

page 600.

◆Updated parameter list under "Specifying Static Interfaces for a

Multicast Router" on page 614.

◆Updated parameter list under "Filtering IGMP Query Packets and

Multicast Data" on page 623.

◆Updated parameter list under "Displaying Multicast Groups Discovered

by IGMP Snooping" on page 624.

◆Added the section "MLD Snooping (Snooping and Query for IPv6)" on

page 634.

◆Added parameter for Forwarding Priority under "Configuring MVR6

Domain Settings" on page 662.

◆Added description of commands "clock summer-time (date)" on

page 757, "clock summertime (predefined)" on page 758, and "clock

summertime (recurring)" on page 759.

◆Updated parameter list for the command "copy" on page 720.

BOUT

HIS

UIDE

– 8 –

◆Updated syntax for the command "delete" on page 723.

◆Updated range for the command "exec-timeout" on page 730.

◆Added the command "terminal" on page 737.

◆Updated parameter options for the command "snmp-server

enable traps" on page 778.

◆Added the command "snmp-server enable port-traps mac-notification"

on page 781 and "show snmp-server enable port-traps" on page 782,

◆In Chapter "Flow Sampling Commands" on page 803 - removed and

replaced previous commands with descriptions of a new command set.

◆Added the command "accounting commands" on page 830.

◆Added description of new command "mac-learning" on page 874.

◆Updated the description of command usage under "port security" on

page 875.

◆Added description of new command "port security mac-address-as-

permanent" on page 877.

◆Added description of new command "ip dhcp snooping limit rate" on

page 904.

◆Added description of new command "ipv6 dhcp snooping option

remote-id" on page 913.

◆Added description of new command "ipv6 dhcp snooping option

remote-id policy" on page 914.

◆Updated parameters for the commands "ip source-guard binding" on

page 920 and "ip source-guard max-binding" on page 923.

◆Added description of new command "ip source-guard mode" on

page 924.

◆Added the new command "clear ip source-guard binding blocked" on

page 924

◆Updated syntax of command "show ip source-guard binding" on

page 925.

◆Added new section describing commands for "IPv6 Source Guard" on

page 926.

◆Added option to allow zeros for command "ip arp inspection validate"

on page 935.

◆Added new parameters for IPv4 and IPv6 filters to the command

"permit, deny (MAC ACL)" on page 965.

BOUT

HIS

UIDE

– 9 –

◆Added the command "clear access-list hardware counters" on

page 973.

◆Updated description of parameters for the command "capabilities" on

page 977.

◆Added the command "discard" on page 979.

◆Added description of seven new DDM commands beginning

with"transceiver-threshold-auto" on page 989 and ending with

"transceiver-threshold voltage" on page 995.

◆Added the command "port channel load-balance" on page 1004.

◆Added the command "lacp timeout" on page 1011.

◆Added the command "storm-sample-type" on page 1029.

◆Updated descriptions of commands "auto-traffic-control alarm-clear-

threshold" on page 1037 and "auto-traffic-control alarm-fire-threshold"

on page 1038 now able to be set using packet rate (packets per

second).

◆Added description of new command "loopback-detection action" on

page 1048 and removed the command loopback-detection mode.

◆Updated information in Command Usage section for the command

"show mac-address-table" on page 1061.

◆Added description of new command "spanning-tree tc-prop-stop" on

page 1088.

◆Updated parameters for "protocol-vlan protocol-group (Configuring

Interfaces)" on page 1155.

◆Added address mask parameter to the command "mac-vlan" on

page 1160.

◆Updated parameters for the command "match" on page 1186.

◆Updated range for the command "ip igmp snooping priority" on

page 1206.

◆Added the commands "clear ip igmp snooping groups dynamic" on

page 1220 and "clear ip igmp snooping statistics" on page 1221.

◆Added description of new commands"ip igmp authentication" on

page 1230 and "show ip igmp authentication" on page 1235.

◆Updated range for the command "ip igmp max-groups" on page 1233.

◆Added the commands "ip multicast-data-drop" on page 1234 and

"show ip multicast-data-drop" on page 1238.

BOUT

HIS

UIDE

– 10 –

◆Added new section "MLD Snooping" on page 1239.

◆Added new section "MLD Filtering and Throttling" on page 1249.

◆Updated range for the command "mvr priority" on page 1262.

◆Added commands "clear mrv groups dynamic" on page 1269 and "clear

mrv statistics" on page 1270.

◆Added commands "clear mvr6 groups dynamic" on page 1288 and

"clear mvr6 statistics" on page 1288.

◆Updated description of parameters for "ethernet cfm cc ma interval" on

page 1339.

◆Added command "clear efm oam event-log" on page 1366.

◆Added the section "DHCP Relay Option 82" on page 1389.

◆Updated the description of command "ip address" on page 1396 to

include using classless subnet format for the ip address subnet mask.

◆Updated parameters for the command "traceroute6" on page 1423.

◆Added the section "ND Snooping" on page 1430.

APRIL 2013 REVISION

This is the second version of this guide. This guide is valid for software

release v1.0.0.0. It includes the following correction to the manual:

◆Updated information in the Command Usage section under "spanning-

tree bpdu-filter" on page 1077.

MARCH 2012 REVISION

This is the first version of this guide. This guide is valid for software release

v1.0.0.0.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Edge-Core Router di rete

Edge-Core

Edge-Core EWS100 Manuale utente

Edge-Core

Edge-Core ECS4210-12P Manuale utente

Edge-Core

Edge-Core ECS3510-28T Manuale di programmazione

Edge-Core

Edge-Core AS4630-54TE Manuale utente

Edge-Core

Edge-Core ES4612 Manuale di programmazione

Edge-Core

Edge-Core AS7926-40XKFB Manuale utente

Edge-Core

Edge-Core ECS4620-28F Manuale utente

Edge-Core

Edge-Core ES4625 Manuale utente

Edge-Core

Edge-Core ECS2000-50T Manuale utente

Edge-Core

Edge-Core EC3805F Manuale utente

Edge-Core

Edge-Core Wedge100BF-32QS Manuale utente

Edge-Core

Edge-Core ES3510 Manuale utente

Edge-Core

Edge-Core ECS4310-26T Manuale utente

Edge-Core

Edge-Core AS7946-30XB Manuale utente

Edge-Core

Edge-Core AS5835-54X Manuale utente

Edge-Core

Edge-Core ES4624-SFP Manuale di programmazione

Edge-Core

Edge-Core AS9516-32D Manuale utente

Edge-Core

Edge-Core DCS209 Manuale utente

Edge-Core

Edge-Core ECS4510-12PD Manuale utente

Edge-Core

Edge-Core ECS4610-24F Manuale utente

Edge-Core

Edge-Core AS5710-54X Manuale utente

Edge-Core

Edge-Core ECS4510-28F Manuale utente

Edge-Core

Edge-Core ES3528M-PoE Manuale utente

Edge-Core

Edge-Core ECS4100-26TX Manuale utente

Manuali Router di rete popolari di altre marche

Allnet

Allnet ALL0333AU Manuale utente

HomeSeer

HomeSeer HT-SEL Manuale utente

Sercomm

Sercomm Genesis OC3505D Manuale utente

Billion

Billion BIPAC 5102 Series Manuale utente

TP-Link

TP-Link TD-8817 Manuale utente

Motorola

Motorola MR1900 Manuale utente

Digi

Digi IX14 Manuale utente

Cisco

Cisco NCS 540 Manuale

XAVi

XAVi X8821e Manuale utente

BEC

BEC 6200WZL Manuale utente

MikroTik

MikroTik hAP ac3 Series Manuale utente

Korenix

Korenix JetNet 5428G Series Manuale utente

NETGEAR

NETGEAR FS526T - Switch Manuale utente

Korenix

Korenix JetNet 5710G Series Manuale utente

Automated Logic

Automated Logic ZN551 Manuale del proprietario

Cisco

Cisco ASR 1000 Series Manuale dell'operatore

EnGenius

EnGenius ESR-9710 Manuale utente

Cisco

Cisco 805 Series Istruzioni operative e di sicurezza