Ei Electronics Ei127 Manuale utente

Pattress Models Ei127 & Ei127R

For use only with Ei140, 141, 144, 145, 146, 161, 161R,

164, 164R, 166, 166R Easi-Fit Smoke/Heat Alarms

The Smoke/Heat Alarm is mounted on the Ei127 & Ei127R.

The Ei127 pattress facilitates installation of bulky wiring and con-

duits.

The Ei127R has an additional socket for connecting to the R

spade terminal on the Ei161R, Ei164R or Ei166R. This can be

used for remote test & hush or manual call points.

WARNING: This pattress must only be used with one of the

above smoke alarms as per these instructions - otherwise the unit

will not comply with the mandatory safety regulations.

Installation

WARNING: First disconnect the mains from the circuit to be used.

1. Choose a mounting position following the siting instructions in

the Smoke/Heat Alarm leaflet. Where the incoming wiring is on

the surface of the ceiling, the appropriately sized ducting/conduit

must be chosen to mate with the unit. Use a sharp knife to

remove material from the selected knockout, making sure that

there is no gap when mated with ducting / conduit. There are four

knockouts – three on the sidewall and one on the rear.

2. Screw the pattress to the ceiling after first removing the

required knockout and bringing the house wires through it (see

figure 1). Use the longer screws and plasterboard anchors from

the Smoke Alarm pack for this task. If the central knockout is

SURFACE

CONDUIT

CABLE

ENTRY

Ei161R/164R/166R

REMOTE CONTROL ONLY

CONNECT TO SMOKE / HEAT ALARM

MOUNTING PLATE TERMINALS

EARTH - (IF PRESENT)

N - NEUTRAL

IC - INTERCONNECT

L - LIVE

REAR

KNOCKOUT

FOR MOUNTING PLATE

Figure 1

being used, seal around the wires (and the openings at the rear

of the pattress) with silicone or similar to prevent air draughts

affecting the smoke entering the alarm.

3. Connect the house wires (L - Live, N - Neutral and IC -

Interconnect, if it is being used) to the terminal block on the pat-

tress. If an Ei161R, Ei164R or Ei166R (with remote TEST/HUSH)

is being installed, attach the “R” wire from the Ei152 (see the

Ei152 instructions) to the terminal marked “R” in the pattress (see

figure 1). If the Ei161R, Ei164R or Ei166R is being used with a

manual call point then connect the R terminal to the call point (see

figures 1& 2). Otherwise do not connect anything to the ”R” termi-

nal.

4. Connect the three wires (L, N and IC) from the pattress con-

nector block to the connectors on the Smoke/Heat Alarms mount-

ing plate. Connect the earth wire (if present) from the house wir-

ing directly to the terminal on the mounting plate. Replace the

cover over the terminal wires.

Note: that the house wiring can be connected directly to the

mounting plate if the pattress terminals are not being used for

looping.

5. Screw the mounting plate to the pattress pillars using the two

screws supplied with this kit.

6. Slide the alarm on to the mounting plate.

7. Connect the mains power – the green LED light on the alarm

should be on. When the test button is pressed the horn should

sound.

If an Ei128R or Ei128RBU pattress with relay is being used,

replace the Ei127R with the Ei128R or Ei128RBU and follow the

instructions supplied with it.

Aico Ltd

Mile End Business Park,

Maesbury Road, Oswestry, Shropshire SY10 8NN, U.K.

Telephone: 0870 7584000 www.aico.co.uk

Ei Electronics

Shannon Industrial Estate,

Shannon, Co. Clare, Ireland

www.eielectronics.com

Figure 2

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Ei Electronics Rilevatore di fumo

Ei Electronics

Ei Electronics Ei 181 Ionisation Manuale utente

Ei Electronics

Ei Electronics Ei605 Series Manuale utente

Ei Electronics

Ei Electronics Ei650iW Manuale utente

Ei Electronics

Ei Electronics Ei 184 Manuale utente

Ei Electronics

Ei Electronics Ei2110 Manuale utente

Ei Electronics

Ei Electronics Ei146 Optical Manuale utente

Ei Electronics

Ei Electronics Ei160 Manuale

Ei Electronics

Ei Electronics Ei100R Manuale utente

Ei Electronics

Ei Electronics RadioLINK Ei 405TY Manuale

Ei Electronics

Ei Electronics EiA600 Series Manuale utente

Ei Electronics

Ei Electronics Ei 100B Ionisation Manuale di istruzioni

Ei Electronics

Ei Electronics MCP401RC Manuale utente

Ei Electronics

Ei Electronics Ei 100TYC Ionisation Manuale utente

Ei Electronics

Ei Electronics Ei603CRF Manuale utente

Ei Electronics

Ei Electronics Ei144 Heat Manuale utente

Ei Electronics

Ei Electronics Ei405TY RF Optical Manuale utente

Ei Electronics

Ei Electronics aico Ei146e Manuale utente

Ei Electronics

Ei Electronics Ei2110e Series Manuale utente

Ei Electronics

Ei Electronics Ei166R Manuale utente

Ei Electronics

Ei Electronics Ei 3105TYCH Optical Manuale utente

Ei Electronics

Ei Electronics RF Tool Manuale utente

Ei Electronics

Ei Electronics Ei186 Manuale utente

Ei Electronics

Ei Electronics Ei161RC Ionisation Manuale utente

Ei Electronics

Ei Electronics Ei141 Ionisation Manuale utente

Manuali Rilevatore di fumo popolari di altre marche

x-sense

x-sense SD19-W Manuale utente

BRK electronic

BRK electronic First Alert P1010 Manuale utente

FireAngel

FireAngel Thermoptek ST-622 Manuale utente

teko

teko Astra-42A Manuale utente

Safetec

Safetec SDS-2/6 Manuale del proprietario

Siemens

Siemens PE-11C Manuale utente

System Sensor

System Sensor DH500ACDC Manuale utente

Resolution Products

Resolution Products RE612 CryptiX Manuale utente

First Alert

First Alert PC900V Manuale utente

Eminent

Eminent EM6590 E-Domotica Manuale utente

Carrier

Carrier Kidde Quell Q301 Manuale utente

VESDA

VESDA VLF-500 Manuale utente

ELRO

ELRO FS8110 Manuale utente

Heiman

Heiman SMOKI NS-626PHS Manuale utente

Regin

Regin SDD-S65 Manuale utente

Family Gard

Family Gard FG225 Manuale utente

Greystone

Greystone DSD120 Manuale utente

Aparton

Aparton ASD-10 Manuale utente