Ekwb EK-Pro RTX A5500 Rack - Ni+Inox Manuale utente

USER GUIDE

GPU WATER BLOCK

EK-Pro

RTX A5500 Rack - Ni+Inox

If this product is made from aluminum and can be only used

with other aluminum liquid cooling components, such as Al

ﬁttings, water blocks and radiators. Mixing aluminum with

copper and brass products can cause galvanic corrosion of

the metal and render liquid cooling equipment useless. Such

misuse is not covered by warranty.

Before you start using this product, please follow these basic guidelines:

Please carefully read the manual before beginning with the

installation process!

Please remove your graphics card from the computer to

assure safest mounting process in order to prevent any

possible damages to your GPU and/or graphics card circuit

board (PCB).

The EK Fittings require only a small amount of force to screw

them ﬁrmly in place since the liquid seal is ensured by the

rubber O-ring gaskets.

The use of corrosion inhibiting coolants is always

recommended for liquid cooling systems, and mandatory for

nickel plated water blocks!

Do not use pure distilled water! For best results EK

recommends the use of EK-CryoFuel coolants!

Make sure to thoroughly bleed air out of your water block, or

you will not reach optimal performance!

- 3 -

TABLE OF CONTENTS

BOX CONTENTS 4

WATER BLOCK DIMENSIONS 5

WATER BLOCK SPECIFICATIONS AND MAIN PARTS 6

PREPARING THE GRAPHICS CARD 7

CLEANING THE PCB 7

CUTTING AND PLACING THERMAL PADS 8

CUTTING AND PLACING THERMAL PADS 9

UNPACKING AND REASSEMBLYING 9

INSTALLING THE WATER BLOCK 10

MOUNTING PCB ON THE WATER BLOCK 10

ATTACHING THE BACKPLATE TO THE GRAPHICS CARD 11

MOUNTING BACKPLATE ON PCB 11

CHECKING FOR CONTACT 12

INSERTING THE GRAPHICS CARD INTO THE CHASSIS 12

TESTING THE LOOP 12

SUPPORT AND SERVICE 13

SOCIAL MEDIA 13

- 4 -

4 mm

10 mm

Allen Key 2 mm (1 x) Screw size guide (1x) 103012

068-alu-RTX A5000 Backplate

Rack (Bl. Elox) 104950

Thermal Pad F 1.0 mm (120 x 16 mm)

(10x) (3830046996732)

Thermal Grease

3830046998477 (1x)

M2.5x10 AX1 Screw (4x)

M2.5x4 AX1 Screw (5x)

Polyamid Washer M2.5 x 0.7mm

selfglued (4x)

Polyamid Washer M2.5 x 0.5 mm

(5x)

120 mm

16 mm

7 mm

M2.5x7 AX1 Screw (5x)

BOX CONTENTS

EK-Pro RTX A5500 Rack

068-Mounting RTX A5500 Rack

Note: There are additional screws in the mounting kit.

- 5 -

WATER BLOCK DIMENSIONS

19.7 mm

141.2 mm

299.7 mm

128.6 mm

311.1 mm

101 mm

23.5 mm

- 6 -

WATER BLOCK SPECIFICATIONS AND MAIN PARTS

Technical Speciﬁcation:

- Dimensions (LxHxW): 311.1 x 141.2 x 23.5 mm

Pos. EAN Description Qty.

106504

RTX A5500 Coldplate - rack 1

104949

RTX A5000 Backplate - rack 1

104956

RTX A5000 Top - rack 1

102696

Standoff M3.5/M2.5 x 2.5 8

101436

Standoff M3/M2.5 x 12.0

63831109861042

EK-FC Pro Terminal Angled 45 deg

105106

Power adapter

103698

RTX A5000 bracket 1

102697

Standoff M3.5/M2.5 x 6.60 1

103090

Screw ISO M3 x 6 24

9049

Screw M2.5x7 5

104647

GPU insert 1

8483

Screw ISO 7380 - UNC6-32 x 5 1

102490

Pro GPU Bracket standoff M4 1

105047

O-ring 166.75 x 2 1

9029

Screw M3 x 6 DIN7991 2

102549

GPU Jet 1

8323

Screw M4 x 28 DIN7984 2

101878

Screw M4 x 45 DIN7984 1

5155

O-ring 15 x 1 2

8627

Washer POLYAMID M2.5 0.7 mm selfglued

9047

Screw M2.5 x 4 4

104344

Screw M2.5 x 10 3

8623

Washer POLYAMID M2.5 0.5 mm 4

18 12

- 7 -

PREPARING THE GRAPHICS CARD

CLEANING THE PCB

Place your graphics card on the ﬂat surface and carefully remove

the stock cooler. Do not forget to unplug all fan connectors. Pay

attention to the following steps when installing the EK-RTX A5500

Rack water block onto your graphics card.

Wipe off the remains of the original thermal compound using a

nonabrasive cloth or Q-tip, as shown in the sample image, until the

components and circuit board are completely clean. EK recommends

the use of denatured alcohol for removing TIM leftovers. After that,

remove all remaining stock thermal pads from the PCB.

NONABRASIVE

CLOTH

- 8 -

STEP 1

Your GPU water block comes with thermal pads that have to be cut

into smaller pieces to cover all the VRM components, such as COILs,

MOSFETs, and drivers.

You must remove the protective foil from both sides of the

thermal pad before installation.

Thermal pads:

10x Thermal Pad F 1.0 mm – (120 x 16 mm) EAN: 3830046996732

STEP 1

1 mm

120 mm

16 mm

Thermal PAD F 1.0 mm (120 x 16 mm)

STEP 2

Once cut to size, thermal pads should be placed on the PCB, as

illustrated below. EK made sure to provide you with more than an

adequate quantity of thermal pads to complete this Step.

STEP 2

CUTTING AND PLACING THERMAL PADS

Thermal Pad F 1.0 mm (5 pcs)

(3830046996732)

For this Step, you will need:

120 mm

16 mm

F1 F1

Thermal Pad F 1.0 mm

- 9 -

Phillips Head

Screwdriver

STEP 1

Apply the enclosed EK-TIM Ectotherm thermal grease (thermal compound)

on the GPU heat spreader – IHS – as shown in the image. The layer of the

thermal compound must be thin and even over the entire surface of the IHS.

The excessive or uneven application of thermal grease may

lead to poor performance!

After unboxing the preinstalled water block, carefully put it on soft

surface. Untighten four (4) screws AX1 M2.5 x 7 and remove foam

and RTX A5000 Backplate – rack. Untightened four (4) screws AX1

M2.5 x 7 and foam will not be needed anymore.

CUTTING AND PLACING THERMAL PADS

UNPACKING AND REASSEMBLYING

STEP 1

Thermal Grease

For this Step, you will need:

FOAM

AX1 M2.5 x 7 (4x)

RTX A5000

BACKPLATE -

RACK

- 10 -

INSTALLING THE WATER BLOCK

SCREW M3 x 6

DIN7991 - INOX (2x)

WASHER

POLYAMID

M2.5 0.7 mm

SELFGLUED

PCB POWER

CONNECTOR

POWER

ADAPTER

This procedure is the same for all full-cover water blocks.

STEP 1

MOUNTING PCB ON THE WATER BLOCK

Firstly, stick three (3) Washer POLYAMID M2.5 0.7 mm selfglued, on the top of 3

the biggest standoffs.

Carefully position the graphic card on water block with preinstalled standoffs.

During this process, make sure you have aligned mounting holes of the PCB with

holes of the water block.

Unscrew two (2) preinstalled M3 x 6 DIN7991 screws to properly place the PCB power

connector in power adapter. After placement is done, tighten them on place again.

Pay attention not to use too much force when pressing the PCB down

to the block since chip dies are prone to cracking.

Tighten four (4) screws AX1 M2.5 x 4 with belonging 4 Washers M2.5 x 0.5 as

shown in the picture. Tighten the screws evenly using the Phillips head screwdriver.

Allen Key 2 mm

M2.5x4 AX1 Screw (4x)

Polyamid Washer M2.5

x 0.7mm selfglued (4x)

Polyamid Washer

M2.5 x 0.5 mm (3x)

Phillips Head Screwdriver

For this Step, you will need:

4 mm

SCREW AX1 M2.5 x 4 (4x)

WASHER M2.5 x 0.5 mm (4x)

Indice

Altri manuali ekwb Hardware per computer

ekwb

ekwb EK-FC R9-295X2 Manuale

ekwb

ekwb EK-FC980 GTX Ti Strix Manuale

ekwb

ekwb EK-FB GA 990FXA-UD7 Manuale

ekwb

ekwb EK-Quantum Kinetic FLT D5/DDC Body D-RGB Manuale utente

ekwb

ekwb EK-FC Titan Z Manuale

ekwb

ekwb EK-FC 5970 Manuale

ekwb

ekwb EK-FC R9-390X TF5 Guida

ekwb

ekwb EK-FC7870 GTX Manuale

ekwb

ekwb EK-KIT HT Series Manuale utente

ekwb

ekwb Velocity - Intel Manuale utente

ekwb

ekwb EK-FC780 GTX Ti Matrix Manuale

ekwb

ekwb EK-Quantum Velocity 2 Manuale utente

ekwb

ekwb EK-FC 4890 VAPOR X Guida

ekwb

ekwb EK-Annihilator EX/EP Series Manuale utente

ekwb

ekwb EK-FC 6970 V2 Manuale

ekwb

ekwb EK-Quantum Convection M.2 NVMe Manuale utente

ekwb

ekwb EK-Pro GPU WB RTX 4000 - Ni + Inox Manuale utente

ekwb

ekwb EK-FB ASRock X399 RGB Monoblock Manuale utente

ekwb

ekwb EK-FC1080 GTX FTW Guida

ekwb

ekwb EK-Quantum Vector RTX 3080/3090 D-RGB Manuale utente

ekwb

ekwb EK-FC1080 GTX TF6 Backplate Manuale

ekwb

ekwb EK-FB KIT GA-X99 LE Guida

ekwb

ekwb EK-FC 780 GTX Ti DCII Manuale

ekwb

ekwb EK-DBAY RES SPIN Guida

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente

ekwb EK-Pro RTX A5500 Rack - Ni+Inox Manuale utente

Manuali Hardware per computer popolari di altre marche