Eldes ESIM4 Manuale utente

ESIM4

ESIM4 Q

Battery Powered GSM Auto Dialler/

Mini Alarm System

EN ESIM4 Manual v1.5

User Manual v1.5

Valid for ESIM4 v03.01.04 and up.

SAFETY INSTRUCTIONS

Please read and follow these safety guidelines in order to maintain safety of operators and people around:

• Battery powered GSM auto dialler/mini alarm system ESIM4/ESIM4 Q (later referenced as “the system”, “the device” or “ESIM4”) is

equipped with a radio transceiver operating in GSM900/1800 bands / GSM850/900/1800/1900 bands respectively.

• DO NOT use the system where it can cause potential danger and interfere with other devices – such as medical devices.

• DO NOT use the system in hazardous environment.

• DO NOT expose the system to high humidity, chemical environment or mechanical impact.

• DO NOT attempt to repair the system yourself – any repairs must be carried out by fully qualied personnel only.

ESIM4 is a device that must be installed in limited access areas. Any system repairs must be done only by qualied, safety

aware personnel.

Remove all batteries before installing. Never install or carry out maintenance during stormy weather.

The system must be powered by four 1,5 V lithium AA type batteries only. When inserting the batteries into the battery slots,

mind the polarity terminals! Any additional device you connect to the system, such as a computer, must be powered by an EN

60950-1 approved supply.

To switch the system o, remove all four 1,5 V lithium AA type batteries.

Fuse F1 model – miniSMDC 0,5A. Replacement fuses have to be exactly the same as indicated by the manufacturer.

If you use a computer for the device conguration, it must be earthed.

The WEEE (Waste Electrical and Electronic Equipment) symbol on this product (see left) means it must not be disposed of in

household waste. To prevent possible harm to human health and/or the environment, you must dispose of this product in an

approved and environmentally safe recycling facility. For further information contact your system supplier, or your local waste

authority.

ESIM4 Manual v1.5

CONTENTS

1. GENERAL INFORMATION ...........................................................................................................................................................6

2. TECHNICAL SPECIFICATIONS ....................................................................................................................................................6

2.1. Electrical and Mechanical Characteristics.....................................................................................................................................................6

2.2. Main Unit and LED and Connector Functionality .........................................................................................................................................7

2.3. Wiring Diagrams ................................................................................................................................................................................................8

3. INSTALLATION ...........................................................................................................................................................................9

4. GENERAL OPERATIONAL DESCRIPTION..................................................................................................................................10

5. CONFIGURATION METHODS ....................................................................................................................................................10

5.1. SMS Text Messages.........................................................................................................................................................................................10

5.2. ELDES Conguration Tool ..............................................................................................................................................................................10

5.3. QR Codes ...........................................................................................................................................................................................................11

6. SMS PASSWORD.......................................................................................................................................................................11

7. USER PHONE NUMBERS ..........................................................................................................................................................12

8. DATE AND TIME........................................................................................................................................................................13

8.1. Automatic Date and Time Synchronization ................................................................................................................................................13

9. SLEEP AND WAKE-UP MODES .................................................................................................................................................14

9.1. Wake-Up Scheduler ........................................................................................................................................................................................15

10. INPUTS....................................................................................................................................................................................16

10.1. Input Z1 ..........................................................................................................................................................................................................16

10.1.1. Digital Mode...................................................................................................................................................................................................17

10.1.2. Analog Mode..................................................................................................................................................................................................18

10.1.3. AUX Output....................................................................................................................................................................................................18

10.2. Input Z2 ..........................................................................................................................................................................................................19

10.2.1. Digital Mode.................................................................................................................................................................................................. 20

10.2.2. Temperature Sensor Mode .........................................................................................................................................................................21

10.2.3. iButton Key Mode .........................................................................................................................................................................................23

10.3. Alarm/Restore Notications...................................................................................................................................................................... 24

10.3.1. Alarm Delay................................................................................................................................................................................................... 26

11. SHOCK SENSOR.......................................................................................................................................................................27

12. ALARM/RESTORE NOTIFICATION SCHEDULER..................................................................................................................... 28

13. OUTPUT ................................................................................................................................................................................. 29

13.1. Output Name................................................................................................................................................................................................... 29

13.2. Turning Output ON and OFF ......................................................................................................................................................................... 29

14. BATTERY LEVEL MONITORING ...............................................................................................................................................32

15. ARMING AND DISARMING.......................................................................................................................................................33

16. SYSTEM INFORMATION. STATUS SMS................................................................................................................................... 34

16.1. Periodic Status SMS ....................................................................................................................................................................................... 34

17. SYSTEM NOTIFICATIONS ........................................................................................................................................................35

18. EVENT MEMORY .....................................................................................................................................................................37

19. REMOTE LISTENING............................................................................................................................................................... 38

20. TECHNICAL SUPPORT ........................................................................................................................................................... 39

20.1. Troubleshooting ............................................................................................................................................................................................. 39

20.2. Restoring Default Parameters ..................................................................................................................................................................... 39

20.3. Updating the Firmware via USB Cable ........................................................................................................................................................ 39

21. RELATED PRODUCTS ............................................................................................................................................................. 40

EN ESIM4 Manual v1.5

Limited Liability

The buyer agrees that the system will reduce the risk of re, theft, burglary or other danger but that it does not guarantee against the oc-

currence of such events. “ELDES UAB” will not take any responsibility for the loss of personal eects, property or revenue whilst using the

system. The liability of “ELDES UAB” is limited to the value of the system purchased. “ELDES UAB” is not aliated with any mobile/wireless/

cellular provider and is therefore not responsible for the quality of such services.

Manufacturer Warranty

The system carries a 24-month manufacturer warranty from “ELDES UAB”. The warranty begins the day the system is purchased by the

user and the receipt must be retained as proof of purchase date. The warranty remains valid only if the system is used as intended, fol-

lowing all guidelines outlined in this manual and in accordance with the operating conditions specied. The warranty is void if the system

has been exposed to mechanical impact, chemicals, high humidity, uids, corrosive and hazardous environments or force majeure factors.

Dear Customer,

Thank you for choosing to purchase the battery powered GSM dialler ESIM4. Your thoughtful decision will ensure reliable solution for

many years as all ELDES products are manufactured to meet the highest standards.

We are condent that you will be completely satised with your product. However, in the unlikely event that you do experience a

problem, please contact the dealer from whom you made your purchase.

UAB ELDES

www.eldes.lt

Contents of Pack

Item Quantity

ESIM4 ...........................................................1

User manual................................................1

1,5 V Lithium AA batteries........................4

GSM antenna............................................... 1

Plastic gland................................................ 1

Screws. ........................................................2

Terminal block... .........................................1

Not included:

• SIM card – we recommend you get a contract SIM, not Pay As You Go.

• miniUSB cable - can be obtained from your local distributor.

• Temperature sensor - can be obtained from your local distributor.

• Microphone - can be obtained from your local distributor

• iButton key reader- can be obtained from your local distributor

• iButton keys - can be obtained from your local distributor

• Buzzer - can be obtained from your local distributor

ESIM4 Manual v1.5

It is strictly forbidden to copy and distribute information in this document or pass to a third party without an

advanced written authorization from “ELDES UAB”. “ELDES UAB” reserves the right to update or modify this

document and/or related products without a warning. Hereby, “ELDES UAB” declares that the battery pow-

ered GSM auto dialler/mini alarm system ESIM4 is in compliance with the essential requirements and other

relevant provisions of Directive 1999/5/EC. The declaration of conformity may be consulted at www.eldes.lt.

EN ESIM4 Manual v1.5

1. GENERAL INFORMATION

ESIM4 is a micro-controller based device used to inform users about the alarm in automatic or security systems, supply power to an auxiliary

device and control one electrical appliance or measure temperature. The device can also be used as a mini-alarm system.

Examples of using the system:

• Suitable in areas without a 230V power supply.

• Switching one electronic device ON/OFF.

• Notication of failure or restoration of an electronic device via SMS text message and/or phone call.

• Property security.

• Temperature monitoring.

• Lighting, garden watering, water pump and other electrical equipment control via SMS text messages.

• Remote listening to what is happening in the secured area.

Main features:

• Conguration by SMS text message and PC.

• Sleep mode for battery power saving for up to 2 years.

• Up to 10 users for system conguration, control and acceptance of system event notications by SMS text messages and phone calls.

• 2 inputs on board turning to 4 inputs when ATZ mode enabled.

• Inputs Z1-Z4 customizable to NC or NO.

• Input Z1/Z3 modes: digital or analog.

• 1 AUX output operating in accordance with the set up period.

• Input Z2/Z4 modes: digital, temperature sensor or iButton key.

• Mini-alarm system: arming/disarming by iButton key.

• Up to 8 temperature sensors support for temperature monitoring in dierent areas.

• 1 open-collector output for electrical appliance control.

• Built-in shock sensor for alarm/restore notication by SMS text message on vibration detection.

• Scheduled system operation in Wake-Up mode and on system event.

• Scheduled input alarm/restore notications.

• Periodic self-test notication by SMS text message to user phone number.

• Customizable notication texts.

• QR code generator allowing to arrange a single or multiple text commands in a single SMS text message and encrypt it in a QR code.

2.TECHNICAL SPECIFICATIONS

2.1. Electrical and Mechanical Characteristics

Battery type............................................................................................1.5 V Lithium AA type batteries

Number of batteries ..............................................................................4

Current used in Sleep mode .................................................................30µAmax

GSM modem frequency.........................................................................ESIM4 - 900/1800 Mhz; ESIM4 Q - 850/900/1800/1900 MHz

Number of inputs...................................................................................2

Digital input value range ......................................................................0... 3000mV

Analog input value range .....................................................................0... 24mA

Impulse duration....................................................................................>600ms

Number of auxiliary terminals .............................................................1

Auxiliary output values.........................................................................12V 200mA max

Maximum supported number of temperature sensors ...................8

Number of outputs ................................................................................1

Output circuit..........................................................................................Open collector output.

Output is pulled to COM

when enabled.

1 R

OUT

Output current........................................................................................200mA max

Supported temperature sensor model ..............................................Maxim®/Dallas® DS18S20, DS18B20

Supported iButton key model.............................................................. Maxim®/Dallas® DS1990A

Dimensions .............................................................................................115x90x56mm (4.53x3.54x2.20in)

Enclosure rating .....................................................................................IP 65

Operating temperature range .............................................................-20…+50°C (-30...+55°C with limitations (-4... +122°F (-22... +131°F with

limitations))

Humidity..................................................................................................0-90% RH @ 0...+40°C (0-90% RH @ +32...+104°F) (non-condensing)

ATTENTON: All 4 batteries must be of the same manufacturer.

ESIM4 Manual v1.5

NOTE: We recommend using Camelion P7 lithium 1.5V AA type and Energizer Ultimate lithium 1.5V AA type batteries or other ‘‘ELDES UAB’’

recommended batteries.

2.2. Main Unit and LED and Connector Functionality

OPEN

SIM

C1 Z2 Z1AUX COM

MICDEF

LED

ANT

USB

BATTERY

- -

+ +

- -

GSM

MODEM

1Main Unit Functionality

GSM MODEM GSM network 900/1800 MHz modem

SIM SIM card slot

LED Light-emitting diode indicator

ANT GSM antenna

MIC Microphone

USB Mini USB port

DEF Button for restoring default settings

FW Pins for rmware upgrade

Connectors Description

Z1 Digital input / analog input terminal

Z2 Digital input / temperature sensor or iButton data terminal (DATA)

COM Common terminal

AUX Auxiliary power supply terminal

C1 Open-collector output / temperature sensor or buzzer power

supply positive terminal (+4V)

LED indications Description

1 ash every 0.5 sec. SIM card is not present / PIN code enabled

3 quick ashes every 3 sec. Searching for GSM network

1 ash every 5 sec Connected to GSM network / system operating successfully

1 quick weak ash every 10 sec. The device is operating in Sleep mode

EN ESIM4 Manual v1.5

2.3. Wiring Diagrams

ESIM4

DS18S20, DS18B20

Temperature sensor

AUXC1 COM Z2 Z1

GND

DATA

+4V

Temperature sensor wiring

ESIM4

Alarm system or other appliance

AUXC1 COM

PGM1

PGM2

Z2 Z1

ESIM4

AUX

AUX WIRING

PRESSURE

SENSOR

Gauge pressure transmitter

C1 COM Z2 Z1

PRESSURE

VESSEL

20mA

4mA

ESIM4

Electrical appliance

AUX

Power

supply

C1 COM Z2 Z1

General wiring AUX wiring

Output wiring

2 3

ESIM4

AUXC1 COM Z2 Z1

ESIM4

AUXC1 COM Z2 Z1

iButton

key reader

BUZZER

+ -

brown

white

COM

5,6KΩ 1KΩ2KΩ

Magnet

COM

Magnet

ESIM4

AUXC1 COM Z2 Z1

ESIM4

AUXC1 COM Z2 Z1

iButton

key reader

BUZZER

+ -

brown

white

COM

5,6KΩ 1KΩ2KΩ

Magnet

COM

Magnet

iButton key reader and buzzer wiring Example of input wiring in ATZ mode

ESIM4 Manual v1.5

3.INSTALLATION

For the connection of input/output terminals, use 0.50 mm2(0.02in2 ) 1 thread unshielded cable of up to 100m (328.08ft) length.

1. Wire up the system in accordance with the wiring diagrams (see 2.3 Wiring Diagrams for more details).

2. If necessary to run the wires, drill out a hole of 13mm (0.51in) diameter in the ESIM4 enclosure and insert the plastic gland supplied in

ESIM4 package. The plastic gland must be facing down.

3. The system comes with a GSM antenna that is already connected. If another type of GSM antenna is required, please replace the

standard GSM antenna with an antenna of your choice.

4. When placing the system, follow the recommendations:

Never install in the following locations:

• inside the metal cabinet

• closer than 20cm (7.87in) from the

metal surface and/or power lines

5. Disable the PIN code request of the SIM card by inserting it into a mobile phone and following the proper menu steps.

6. Once the PIN code is disabled, insert the SIM card into the SIM card slot / holder of ESIM4 system.

OPEN

12 14 15

OPEN

7. Insert all 4 batteries and wait until the LED indicator starts blinking indicating successful micro-controller operation. The system is

now running in Wake-Up mode for 3 minutes to congure the system by SMS text messages (see 5. CONFIGURATION METHODS).

8. Change the default SMS password (see 6. SMS PASSWORD for more details).

9. Set the phone number for User 1 (see 7. USER PHONE NUMBERS for more details).

10. Once the LED indicator lights OFF, the system will switch to Sleep mode and it will no longer accept any SMS text messages.

ATTENTION: The system is NOT compatible with pure 3G SIM cards. Only 2G/GSM SIM cards and 3G SIM cards with 2G/GSM prole enabled

are supported. For more details, please contact your GSM operator.

ATTENTION: We also recommend you to disable call forwarding, voice mail/text message reports on missed/busy calls and similar services

that might cause incorrect system operation. Please contact your GSM operator for more details on these services and how to disable them.

EN ESIM4 Manual v1.5

NOTE: For maximum system reliability we recommend you do NOT use a Pay As You Go SIM card. Otherwise, in the event of insucient credit

balance on the SIM card, the system would fail to make a phone call or send SMS text messages.

NOTE: We advise you to choose the same GSM SIM provider for your system as for your mobile phone. This will ensure the fastest, most

reliable SMS text message delivery service and phone call connection.

NOTE: Even though the installation process of ESIM4 is not too complicated, we still recommend to perform it by a person with basic knowl-

edge in electrical engineering and electronics to avoid any system damage.

4.GENERAL OPERATIONAL DESCRIPTION

The battery powered GSM dialler ESIM4 uses the GSM network for event transmission by SMS text message and/or phone call to the listed

user phone numbers. In addition to being informed about alarm and restore events of the inputs, the users can use the system to supply

power to an auxiliary device and control one electrical appliance using an output or measure the temperature using up to 8 temperature

sensors.

The system has two inputs (normally closed or normally open) for a detection device connection. By enabling the ATZ mode and connecting

the resistors, 2 detection devices can be connected to each input. The system also supplies 12 volt power to an auxiliary device, such as,

pressure sensor. In addition, the system comes equipped with a built-in shock sensor for any vibration detection where the system is placed.

ESIM4 can also be used as a mini alarm system supporting arming/disarming feature by iButton key.

ESIM4 can control 1 electrical appliance on receipt of the correct SMS text message or via ELDES Conguration Tool software. For example,

users can turn on or o the heating, lighting, lift the gates, blinds etc.

By default, when an authorised number calls to the system, the device answers and the user can listen for 60 seconds to what is going on in

the premises. This function works only when a microphone is connected. The system will ignore SMS requests and voice calls coming from

unknown phone numbers.

Most of the time the system operates in Sleep mode allowing to save battery power for up to 2 years. However, when an event occurs,

requiring the device to send SMS messages and/or dial one of the listed user phone numbers, the device will switch to Wake-Up mode.

5.CONFIGURATION METHODS

5.1. SMS Text Messages

!!! In this user manual the underscore character ”_” represents one space character. Every underscore character must be

replaced by a single space character. There must be no spaces or other unnecessary characters at the beginning and at the

end of the SMS text message.

SMS

In order to congure and control the system by SMS text message, send the text command to the ESIM4 system phone num-

ber from one of the listed user phone numbers. The system supports multiple text commands arranged in a single SMS text

message. The structure of SMS text message consists of 4-digit SMS password (the default SMS password is 0000 – four

zeros), the parameter and value. For some parameters the value does not apply e. g. STATUS. The variables are indicated in

lower-case letters, while a valid parameter value range is indicated in brackets.

For more details on how to encrypt an SMS text message in a QR code, please refer to 5.3. QR Codes and ELDES Conguration Tool

software’s HELP section.

5.2. ELDES Conguration Tool

Cong

Tool

Software ELDES Conguration Tool is intended for ESIM4 battery powered GSM dialler conguration via USB port locally. This

software simplies system conguration process by allowing to use a personal computer in the process. Before starting to use

ELDES Conguration Tool software, please read the user guide provided in the software’s HELP section.

ELDES Conguration Tool is freeware and can be downloaded at: www.eldes.lt/download

NOTE: Conguration by USB cable and ELDES Conguration Tool software does not require the batteries to be inserted in the device.

Altri manuali per ESIM4

Questo manuale è adatto per i seguenti modelli

Indice

Manuali Sistema di sicurezza popolari di altre marche

Inner Range

Inner Range Concept 2000 Manuale utente

Climax

Climax Mobile Lite R32 Istruzioni per il montaggio

CADDX

CADDX NX-6 Manuale utente

FBII

FBII XL-31 Series Manuale utente

Johnson Controls

Johnson Controls PENN Connected PC10 Manuale utente

Aeotec

Aeotec Siren Gen5 Manuale utente

Blaupunkt

Blaupunkt SA 2700 Manuale utente

IDEAL

IDEAL Accenta Manuale del proprietario

AJAX

AJAX DoubleButton Manuale utente

Swann

Swann SW-P-MC2 Manuale utente

Ecolink

Ecolink Siren+Chime Manuale utente

Digital Monitoring Products

Digital Monitoring Products XR150 Manuale utente

EDM

EDM Solution 6+6 Wireless-AE Manuale utente

Highway Safety Group

Highway Safety Group EA401 Manuale utente

Siren

Siren LED GSM Manuale utente

Detection Systems

Detection Systems 7090i Istruzioni per il montaggio

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuale utente

Siemens

Siemens FDM273 Manuale utente