Eldes ESIM384 Manuale utente

ESIM384

GSM ALARM AND MANAGEMENT SYSTEM

INSTALLATION MANUAL

EN ESIM384 Installation and Conguration Manual v1.1

Installation Manual v1.0

Valid for ESIM384 v01.00

Safety instructions

Please read and follow these safety guidelines in order to maintain safety of operators and people around:

• GSM alarm & management system ESIM384 (also referenced as “alarm system”, “system” or “device”) has radio transceiver operating in

GSM 850/900/1800/1900 bands.

• DO NOT use the system where it can be interfere with other devices and cause any potential danger.

• DO NOT use the system with medical devices.

• DO NOT use the system in hazardous environment.

• DO NOT expose the system to high humidity, chemical environment or mechanical impacts.

• DO NOT attempt to personally repair the system.

• System label is on the bottom side of the device.

GSM alarm system ESIM384 is a device mounted in limited access areas. Any system repairs must be done only by qualied,

safety aware personnel.

The system must be powered by main 16-24V ~50/60 Hz1.5A max or 18-24V 1,5A max power supply which must be

approved by LST EN 60950-1 standard and be easily accessible nearby the device. When connecting the power supply to the

system, switching the pole terminals places does not have any aect.

Any additional devices linked to the system ESIM384 (computer, sensors, relays etc.) must be approved by LST EN 60950-1

standard.

The power supply can be connected to AC mains only inside installation room with auto-

matic 2-pole circuit breaker capable of disconnecting circuit in the event of short circuit

or over-current condition. Open circuit breaker must have a gap between connections

of more than 3mm (0.12in) and the disconnection current 5A.

Phase

AC 230V

50/60Hz/DC 24V

USB cable

Null

ESIM384

AC/DC

Mains power and backup battery must be disconnected before any installation or tuning work starts. The system installation

or maintenance must not be done during stormy conditions

Backup battery must be connected via the connection which in the case of breaking would result in disconnection of one of

battery pole terminals. Special care must be taken when connecting positive and negative battery terminals. Switching the

pole terminals places is NOT allowed.

In order to avoid re or explosion hazards the system must be used only with approved backup battery.

The device is fully turned o by disconnecting 2-pole switch o device of the main power supply and disconnecting backup

battery connector.

Fuse F1 type – Slow Blown 2A. Replacement fuses have to be exactly the same as indicated by the manufacturer.

If you use I security class computer for setting the parameters it must be connected to earth.

ESIM384 Installation and Conguration Manual v1.1

Contents

1. GENERAL INFORMATION.........................................................................................................................................................8

1.1. Functionality......................................................................................................................................................................................................8

1.2. Compatible Device Overview...........................................................................................................................................................................8

1.3. Default Parameters and Ways of Parameter Conguration .......................................................................................................................8

2. Technical Specications .......................................................................................................................................................16

2.1. Electrical and Mechanical Characteristics ..................................................................................................................................................16

2.2. Main Unit, LED Indicator and Connector Functionality .............................................................................................................................17

2.3. Wiring Diagrams ..............................................................................................................................................................................................18

3. INSTALLATION ...................................................................................................................................................................... 24

4. GENERAL OPERATIONAL DESCRIPTION............................................................................................................................... 28

5. CONFIGURATION METHODS ................................................................................................................................................. 29

5.1. SMS Text Messages........................................................................................................................................................................................ 29

5.2. EKB2 LCD Keypad............................................................................................................................................................................................ 29

5.3. EKB3/EKB3W/EWKB4 LED Keypads ........................................................................................................................................................... 30

5.4. ELDES Conguration software..................................................................................................................................................................... 30

5.5. System conguration by USB cable..............................................................................................................................................................31

6. SMS PASSWORD AND INSTALLER CODE................................................................................................................................32

7. SYSTEM LANGUAGE ...............................................................................................................................................................33

8. USER PHONE NUMBERS ....................................................................................................................................................... 34

8.1. User Phone Number Names ..........................................................................................................................................................................35

8.2. System Control from any Phone Number....................................................................................................................................................35

9. DATE AND TIME..................................................................................................................................................................... 36

9.1. Automatic Date and Time Synchronization ............................................................................................................................................... 36

10. MASTER AND USER CODES .................................................................................................................................................. 38

10.1. Master and User Code Names ...................................................................................................................................................................... 40

11. IBUTTON KEYS .......................................................................................................................................................................41

11.1. Adding and Removing iButton Keys............................................................................................................................................................ 41

11.2. iButton Key Names......................................................................................................................................................................................... 42

12. ARMING AND DISARMING..................................................................................................................................................... 43

12.1. Free of Charge Phone Call............................................................................................................................................................................. 44

12.2. SMS Text Message.......................................................................................................................................................................................... 44

12.3. EKB2 Keypad and User/Master Code .......................................................................................................................................................... 45

12.4. EKB3 Keypad and User/Master Code .......................................................................................................................................................... 47

12.5. EKB3W/EWKB4 Keypads and User/Master Code...................................................................................................................................... 49

12.6. iButton Key.......................................................................................................................................................................................................51

12.7. EWK1/EWK2 Wireless Keyfob .......................................................................................................................................................................52

12.8. Arm-Disarm by Zone .......................................................................................................................................................................................53

12.9. Automatic Arm/Disarm by Scheduler...........................................................................................................................................................53

12.10. Disabling and Enabling Arm/Disarm Notications ...................................................................................................................................53

13. EXIT AND ENTRY DELAY ........................................................................................................................................................55

14. ZONES.....................................................................................................................................................................................57

14.1. Zone Numbering.............................................................................................................................................................................................57

14.2. Zone Expansion ...............................................................................................................................................................................................57

14.3. 8-Zone Mode....................................................................................................................................................................................................57

14.4. ATZ (Advanced Technology Zone) Mode.................................................................................................................................................... 58

14.5. Zone Type Denitions ................................................................................................................................................................................... 58

14.6. Zone Attributes .............................................................................................................................................................................................. 59

14.7. Bypassing and Activating Zones.................................................................................................................................................................. 63

14.8. Zone Names .................................................................................................................................................................................................... 63

14.9. Disabling and Enabling Zones ..................................................................................................................................................................... 64

14.10. Viewing Zone State ...................................................................................................................................................................................... 65

15. STAY MODE............................................................................................................................................................................ 66

16. TAMPERS................................................................................................................................................................................67

16.1. Tamper Names................................................................................................................................................................................................ 68

17. ALARM INDICATIONS AND NOTIFICATIONS FOR USER ....................................................................................................... 69

17.1. Enabling and Disabling Alarm Notications................................................................................................................................................71

17.2. Audio Files and Introduction Audio..............................................................................................................................................................72

18. PROGRAMMABLE (PGM) OUTPUTS.......................................................................................................................................73

18.1. PGM Output Numbering .................................................................................................................................................................................73

18.2. PGM Output Expansion...................................................................................................................................................................................73

18.3. PGM Output Names.........................................................................................................................................................................................74

EN ESIM384 Installation and Conguration Manual v1.1

18.4. Disabling and Enabling PGM Outputs...........................................................................................................................................................74

18.5. Turning PGM Outputs ON and OFF................................................................................................................................................................74

18.6. PGM Output Control by Event and Scheduler ............................................................................................................................................ 76

18.6.1. PGM Output Actions and System Events.................................................................................................................................................. 76

18.6.2. Schedulers .....................................................................................................................................................................................................77

18.6.3. Additional Conditions...................................................................................................................................................................................77

18.7. Wireless PGM Output Type Denitions........................................................................................................................................................77

19. WIRELESS DEVICES............................................................................................................................................................... 78

19.1. Pairing, Removing and Replacing Wireless Device ................................................................................................................................... 79

19.2. Wireless Device Information......................................................................................................................................................................... 80

19.3. Wireless Signal Status Monitoring .............................................................................................................................................................. 80

19.4. Disabling and Enabling Siren if Wireless Signal is Lost ............................................................................................................................ 83

19.5. EKB3W/EWKB4 - Wireless LED Keypad...................................................................................................................................................... 83

19.6. EWR2 – Wireless Signal Repeater................................................................................................................................................................ 85

19.7. EWF1/EWF1CO - Wireless Smoke/CO Detector ........................................................................................................................................ 86

19.8. EW2 - Wireless Zone and PGM Output Expansion Module ...................................................................................................................... 88

19.9. EWM1 - Wireless Power Socket.................................................................................................................................................................... 88

19.10. EWKB5 Wireless Touchpad Overview........................................................................................................................................................ 89

20. WIRED SIREN/BELL............................................................................................................................................................. 100

20.1. BELL Output Status Monitoring................................................................................................................................................................. 101

20.2. Bell Squawk................................................................................................................................................................................................... 101

20.3. Bell Squawk in Stay Mode ........................................................................................................................................................................... 102

20.4. Indication by EWS2 - Wireless Outdoor Siren Indicators ....................................................................................................................... 103

20.5. Indication by EWS3 - Wireless Indoor Siren Indicators ..........................................................................................................................104

21. BACKUP BATTERY, MAINS POWER STATUS MONITORING AND MEMORY......................................................................... 105

21.1. Backup Battery Status Monitoring ............................................................................................................................................................ 105

21.2. Mains Power Status Monitoring................................................................................................................................................................. 107

22. GSM CONNECTION AND ANTENNA STATUS MONITORING................................................................................................. 109

22.1. GSM Connection Status Monitoring ..........................................................................................................................................................109

22.2. GSM/GPRS antenna Status Monitoring .................................................................................................................................................... 110

23. PARTITIONS .........................................................................................................................................................................111

23.1. Zone Partition ................................................................................................................................................................................................111

23.2. User Phone Number Partition .....................................................................................................................................................................111

23.3. Keypad Partition and Keypad Partition Switch.........................................................................................................................................112

23.4. User/Master Code Partition ....................................................................................................................................................................... 113

23.5. iButton Key Partition ................................................................................................................................................................................... 114

23.6. EWK1/EWK2 Wireless Keyfob Partition ................................................................................................................................................... 114

24. TEMPERATURE SENSORS ....................................................................................................................................................115

24.1. Adding, Removing and Replacing On-Board Dallas Temperature Sensors..........................................................................................115

24.2. Primary and Secondary Temperature Sensors........................................................................................................................................ 116

24.3. Setting Up MIN and MAX Temperature Thresholds. Temperature Info SMS.......................................................................................117

24.4. Temperature Sensor Names....................................................................................................................................................................... 118

25. REMOTE LISTENING AND 2-WAY VOICE COMMUNICATION.................................................................................................119

26. SYSTEM INFORMATION. INFO SMS..................................................................................................................................... 120

26.1. Periodic Info SMS.......................................................................................................................................................................................... 120

27. SYSTEM NOTIFICATIONS .....................................................................................................................................................122

27.1. SMS Text Message Delivery Restrictions ................................................................................................................................................. 133

27.2. SMSC (Short Message Service Center) Phone Number.......................................................................................................................... 133

28. EVENT AND ALARM LOG ..................................................................................................................................................... 134

28.1. Event Log ....................................................................................................................................................................................................... 134

28.2. Alarm Log....................................................................................................................................................................................................... 135

29. INDICATION OF SYSTEM FAULTS ........................................................................................................................................ 136

30. MONITORING STATION........................................................................................................................................................ 138

30.1. Data Messages – Events.............................................................................................................................................................................. 139

30.2. Communication............................................................................................................................................................................................. 145

31. DUAL SIM MANAGEMENT ....................................................................................................................................................157

31.1. Disabled Mode............................................................................................................................................................................................... 157

31.2. Automatic Mode ........................................................................................................................................................................................... 157

32. WIRED DEVICES................................................................................................................................................................... 158

32.1. RS485 Interface ........................................................................................................................................................................................... 158

32.2. 1-Wire Interface............................................................................................................................................................................................ 167

32.3. Modules Interface ........................................................................................................................................................................................ 167

33. SERVICE MODE .................................................................................................................................................................... 170

34. REMOTE SYSTEM RESTART ................................................................................................................................................ 170

ESIM384 Installation and Conguration Manual v1.1

35. ELDES CLOUD SERVICES ......................................................................................................................................................171

36. TECHNICAL SUPPORT .........................................................................................................................................................172

36.1. Troubleshooting ........................................................................................................................................................................................... 172

36.2. Restoring Default Parameters ................................................................................................................................................................... 172

36.3. Updating the Firmware via USB Cable Locally........................................................................................................................................ 172

36.4. Updating Firmware via GPRS Connection Remotely .............................................................................................................................. 173

36.5. Frequently Asked Questions...................................................................................................................................................................... 173

37. RELATED PRODUCTS............................................................................................................................................................175

38. GLOSSARY – APPENDIX 1.................................................................................................................................................... 178

39. EKB3/EKB3W/EWKB4 COMMANDS - APPENDIX 2 ............................................................................................................ 180

40. SMS COMMANDS - APPENDIX 3 ..........................................................................................................................................191

41. RADIO SYSTEM INSTALLATION AND SIGNAL PENETRATION  APPENDIX 4................................................................... 194

EN ESIM384 Installation and Conguration Manual v1.1

The following terms and conditions govern use of the ESIM384 device and contains important information on limitations regarding the

product’s use and function, as well as information on the limitations of the manufacturer’s liability. Please carefully read these terms and

conditions. For more information on your product, please visit www.eldesalarms.com

TECHNICAL SUPPORT

In order to ensure continuous and proper operation of the ESIM384 device and uninterrupted service, it is the responsibility of the User to

make sure that: (I) the product is properly installed, and (II) there is constant internet or GSM connection and electrical supply (low battery

must be replaced in time).

If you experience diculty during the installation or subsequent use of the system, you may contact ELDES, UAB distributor or dealer in

your country/region. For more information see www.eldesalarms.com

WARRANTY PROCEDURES

Warranty and out of warranty service should be obtained by contacting the system integrator/dealer/retailer/e-tailer or distributor where

the customer purchased the product. When requesting for service, the proof of purchase and the product serial number must be provided.

The return of the defective product should be strictly through the original route of purchase, and the customers shall pack the product

appropriately to prevent the returned product from suering in the transportation.

MANUFACTURER WARRANTY

ELDES provides a limited warranty for its products only to the person or entity that originally purchased the product from ELDES or its

authorized distributor or retailer and only in case of defective workmanship and materials under normal use of the system for a period of

twenty four (24) months from the date of shipment by the ELDES, UAB (Warranty Period). Warranty obligations do not cover expandable

materials (power elements and/or batteries), holders and enclosures. The warranty remains valid only if the system is used as intended,

following all guidelines outlined in this manual and in accordance with the operating conditions specied. The warranty is void if the system

has been exposed to mechanical impact, chemicals, high humidity, uids, corrosive and hazardous environments or force majeure factors.

If a hardware defect arises and a valid claim is received within the Warranty Period, at its own discretion, ELDES, UAB will either (a) repair a

hardware defect at no charge, using new or refurbished replacement parts, or (b) exchange the product with a product that is new or which

has been manufactured from new or serviceable used parts and is at least functionally equivalent to the original product, or (c) refund the

purchase price of the product.

LIMITED LIABILITY

The buyer must agree that the system will reduce the risk of theft, burglary or other dangers but does not provide guarantee against such

events. ELDES, UAB will not assume any responsibility regarding personal or property, or revenue loss while using the system. ELDES, UAB

is not aliated with any of the Internet providers, therefore, it shall not responsible for the quality of Internet service.

ELDES, UAB shall also assume no liability due to direct or indirect damage or loss, as well as unreceived income when using the system, in-

cluding cases, when the damages arise due to the above mentioned risks, when due to breakdown or malfunction the user is not informed

in a timely manner about a risk which has arisen. In any case, the liability of ELDES, UAB, as much as it is allowed by the laws in force, shall

not exceed the price of acquisition of the product.

CONSUMER PROTECTION LAWS

FOR CONSUMERS WHO ARE COVERED BY CONSUMER PROTECTION LAWS OR REGULATIONS IN THEIR COUNTRY OF PURCHASE OR, IF DIF-

FERENT, THEIR COUNTRY OF RESIDENCE, THE BENEFITS CONFERRED BY THIS WARRANTY ARE IN ADDITION TO ALL RIGHTS AND

REMEDIES CONVEYED BY SUCH CONSUMER PROTECTION LAWS AND REGULATIONS. This warranty grants upon you specic legal

rights, and you may also have other rights that vary by country, state or province.

DISPOSAL AND RECYCLING INFORMATION

The WEEE (Waste Electrical and Electronic Equipment) marking on this product (see left) or its documentation indicates that the

product must not be disposed of together with household waste. To prevent possible harm to human health and/or the envi-

ronment, the product must be disposed on in an approved and environmentally safe recycling process. For further information

on how to dispose of this product correctly, contact the system supplier, or the local authority responsible for waste disposal

in your area.

ESIM384 Installation and Conguration Manual v1.1

Content of Pack

Item Quantity Item Quantity

1. ESIM384.......................... ...................................1

2. SMA antenna..................... ................................2

3. Back-up battery connection wire ..................1

3. User manual.......................................................1

5. Resistors 5,6k.................................................16

6. Resistors 3,3k.................................................8

7. Plastic standos......... ......................................4

These following components are optional (sold separately) and are not included in device’s Content of Pack:

Buzzer;

Microphone.

About Installation Manual

This document describes detailed installation and operation process of alarm system ESIM384. It is very important to read the installation

manual before starting to use the system.

It is strictly forbidden to copy and distribute the information contained in this document or to pass thereof to a third

party without an a priori written authorization obtained from ELDES, UAB. ELDES, UAB reserves the right to update or

modify this document and/or related products without an a priori warning. ELDES, UAB hereby declares that GSM alarm

and management system ESIM384 is in compliance with the essential requirements and other relevant provisions of

the Directive 1999/5/EC. The declaration of conformity is available at www.eldesalarms.com.

EN ESIM384 Installation and Conguration Manual v1.1

1. GENERAL INFORMATION

1.1. Functionality

ESIM384 – micro-controller based alarm system for houses, cottages, country homes, garages and other buildings, also capable of manag-

ing electrical appliances via cellular GSM/GPRS network. It can also be used as Intercom system.

Examples of using the system:

• Property security.

• Alarm switch.

• Thermostat, heating and air-conditioner control, temperature

monitoring.

• Lighting, garden watering, water pump and other electrical

equipment control via SMS text messages.

• Remote listening to what is happening in the secured area.

• Mains power status notication by SMS text message.

• Two-way intercom device via GSM network.

1.2. Compatible Device Overview

Wired Devices

Device Description Max. Connectible Devices

EKB2 LCD keypad 4*

EKB3 LED keypad 4*

EA1 Audio output module with 3,5mm jack 1**

EA2 Audio amplier module 1W 8 1**

EPGM1 16 zone and 2 PGM output expansion module 2

ELAN3-ALARM Ethernet communicator 1

EPGM8 8 PGM output expansion module 1**

Wireless Devices

Device Description Max. Connectible Devices

EW2 Wireless 2 zone and 2 PGM output expansion module 16*****

EWP2 Wireless motion detector 32***

EWP3 Wireless motion detector 32***

EWD2 Wireless magnetic door contact/shock sensor/ood sensor 32***

EWD3 Wireless magnetic door contact/shock sensor/ood sensor 32***

EWK1**** Wireless keyfob with 4 buttons 5***

EWK2**** Wireless keyfob with 4 buttons 5***

EWS3 Wireless indoor siren 32***

EWK2A**** Wireless keyfob with 1 button 5***

EWS2 Wireless outdoor siren 32***

EKB3W Wireless LED keypad 4***

EWKB4 Wireless LED keypad 4***

EWKB5 Wireless touchpad 4***

EWF1 Wireless smoke detector 32***

EWF1CO Wireless smoke and CO detector 32***

EWR2 Wireless signal repeater 4***

EWM1 Wireless power socket 32***

* - A mixed combination of EKB2 and EKB3 keypads is supported. The combination can consist of up to 4 keypads in total.

** - Only 1 of these modules can be connected at a time if the module slots are implemented in ESIM384 unit.

*** - A mixed combination of wireless devices is supported. The combination can consist of up to 32 wireless devices in total.

**** - A mixed combination of EWK1, EWK2 and EWK2A keyfobs is supported. The combination can consist of up to 5 keyfobs in total.

***** - EW2 creates 4 wireless zones, therefore the max. number of connectible EW2 devices is 16 if no keypad zones, no EPGM1 and no

virtual zones exist in the system’s conguration.

1.3. Default Parameters and Ways of Parameter Conguration

Main Settings

Parameter Default Value

Congurable by:

SMS EKB2

EKB3/

EKB3W/

EWKB4

Conguration

Software

User 1... 10 name N/A 

User 1... 10 phone number N/A    

User 1... 10 partition Partition 1   

User 1...10 - call in case of alarm Enabled   

Allow control from any phone number Disabled    

SMS password 0000    

SMS language Depends on the rmware

Partition 1 name PART1 

Partition 2 name PART2 

Partition 3 name PART3 

Partition 4 name PART4 

ESIM384 Installation and Conguration Manual v1.1

Partition 1... 4 exit delay 15 seconds    

GSM signal loss indication - delay 180 seconds 

GSM signal loss indication – activate output N/A 

Dual SIM management – SIM card switch Disabled 

Dual SIM management – try to nd operator for a

maximum of 3 time (s) 

Dual SIM management – send SMS/call via Currently in use SIM 

Main Settings

Parameter Default Value

Congurable by:

SMS EKB2

EKB3/

EKB3W/

EWKB4

Conguration

Software

Passwords/Codes

Installer's code 1470   

Duress code N/A   

SGS code N/A   

Passwords/codes format 4-digit 

Prompt additionally for master code when cong-

uring via keypad/software Disabled 

Master code 1111   

Master code name N/A 

Master code partition Partition 1, Partition 2, Partition 3, Parti-

tion 4   

User code 2... 30 N/A   

User code 2... 30 name N/A 

User code 2... 30 partition Partition 1   

Faults

Main power loss Enabled 

Low battery Enabled 

Battery dead or missing Enabled 

Battery failed Enabled 

Wired siren failed Enabled 

RF jammer detected Enabled 

Tamper alarm Enabled 

Date/time not set Enabled 

GSM connection failed Enabled 

GSM antenna failed Enabled 

Wireless antenna failed Enabled 

Communication bus failed Enabled 

Critical CO level Enabled 

Wireless power socket fault Enabled 

Wireless device low battery Enabled 

Communication with MS failed Disabled 

Notications

System armed – User 1... 10 Enabled   

System armed – SMS delivery report Enabled   

System disarmed – User 1... 10 Enabled   

System disarmed – SMS delivery report Enabled   

General alarm – User 1... 10 Enabled   

General alarm – SMS delivery report Enabled   

Main power loss/restore – User 1... 10 Enabled   

Main power loss/restore – SMS delivery report Enabled   

Battery failed – User 1... 10 Enabled   

Battery failed – SMS delivery report Enabled   

Battery dead or missing – User 1... 10 Enabled   

Battery dead or missing – SMS delivery report Enabled   

Low battery – User 1... 10 Enabled   

Low battery – SMS delivery report Enabled   

Siren fail/restore – User 1... 10 Disabled   

EN ESIM384 Installation and Conguration Manual v1.1

Siren fail/restore – SMS delivery report Disabled   

RF jammer detected – User 1... 10 Disabled   

RF jammer detected – SMS delivery report Disabled   

Date/time not set – User 1... 10 Disabled   

Date/time not set – SMS delivery report Disabled   

GSM connection failed – User 1... 10 Disabled   

GSM connection failed – SMS delivery report Disabled   

GSM/GPRS antenna fail/restore – User 1... 10 Disabled   

GSM/GPRS antenna fail/restore – SMS delivery

report Disabled   

Tamper alarm/restore – User 1... 10 Enabled   

Tamper alarm/restore – SMS delivery report Enabled   

Communication bus fail/restore – User 1... 10 Enabled   

Communication bus fail/restore – SMS delivery

report Enabled   

Temperature info – User 1... 10 Enabled   

Temperature info – SMS delivery report Enabled   

System started – User 1... 10 Enabled   

System started – SMS delivery report Enabled   

Periodical info – User 1... 10 Enabled   

Periodical info – SMS delivery report Enabled   

Wireless signal loss – User 1... 10 Enabled   

Wireless signal loss – SMS delivery report Enabled   

Unable to arm – User 1... 10 Enabled   

Unable to arm – SMS delivery report Enabled   

Zone bypass - User 1... 10 Enabled   

Zone bypass – SMS delivery report Enabled   

Critical CO level - User 1... 10 Enabled   

Critical CO level – SMS delivery report Enabled   

Wireless socket signal loss/restore - User 1... 10 Disabled  

Wireless socket signal loss/restore – SMS delivery

report Disabled  

Report/Control zone triggered - User 1... 10 Enabled   

Report/Control zone triggered - SMS delivery

report Enabled   

Incoming SMS forwarding - User 1... 10 Enabled  

Incoming SMS forwarding - SMS delivery report Enabled  

Wireless communication failed - User 1... 10 Disabled   

Wireless communication failed - SMS delivery

report Disabled   

Communication with MS failed - User 1... 10 Disabled 

Communication with MS failed - SMS delivery

report Disabled 

Send to all users simultaneously – all notications Disabled   

Time Synchronization

Time synchronization Disabled 

Phone number of the currently inserted SIM card N/A 

Synchronization frequency 30 days 

Event Log

Event log Enabled    

Zones

Parameter Default Value

Congurable by:

SMS EKB2

EKB3/

EKB3W/

EWKB4

Conguration

Software

On Board

Z1... Z8 zone name Zone1... Zone8  

Z1 type Delay   

Z1... Z8 zone status Enabled    

Z2... Z8 type Instant   

Indice

Manuali Sistema di sicurezza popolari di altre marche

Inner Range

Inner Range Concept 2000 Manuale utente

Climax

Climax Mobile Lite R32 Istruzioni per il montaggio

CADDX

CADDX NX-6 Manuale utente

FBII

FBII XL-31 Series Manuale utente

Johnson Controls

Johnson Controls PENN Connected PC10 Manuale utente

Aeotec

Aeotec Siren Gen5 Manuale utente

Blaupunkt

Blaupunkt SA 2700 Manuale utente

IDEAL

IDEAL Accenta Manuale del proprietario

AJAX

AJAX DoubleButton Manuale utente

Swann

Swann SW-P-MC2 Manuale utente

Ecolink

Ecolink Siren+Chime Manuale utente

Digital Monitoring Products

Digital Monitoring Products XR150 Manuale utente

EDM

EDM Solution 6+6 Wireless-AE Manuale utente

Highway Safety Group

Highway Safety Group EA401 Manuale utente

Siren

Siren LED GSM Manuale utente

Detection Systems

Detection Systems 7090i Istruzioni per il montaggio

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuale utente

Siemens

Siemens FDM273 Manuale utente