Eldes EWS2 Manuale utente

OUTDOOR WIRELESS SIREN

BELAIDĖ LAUKO SIRENA

БЕСПРОВОДНАЯ УЛИЧНАЯ СИРЕНА

EWS2

User Manual v2.1

Compatible with:

• ESIM264 v7.11.08 and up + EWT1 v16.14 and up.

• ESIM364 all versions.

• EPIR v05.05.04 and up + EWT2 v16.14 and up.

• EPIR2 all versions.

Main features:

• Audio alarm indication by built-in speaker;

• Visual alarm indication by built-in LED indicators;

• Range of operating temperature: -30...+55oC.

EWS2 is a wireless outdoor device with a built-in siren speaker, LED indicators and operates with ELDES wireless alarm systems. EWS2

has to be bind to the alarm system by sending a corresponding SMS message or using software ELDES Conguration Tool. Upon su-

ccessful EWS2 binding process, the system adds one wireless zone and one wireless PGM output. In case of alarm, the siren provides

a sound alarm for one minute. The conguration of this parameter is disabled for EWS2 in order to save the battery power.

ESIM264, EPIR and EPIR2 alarm systems support up to 16 EWS2 devices, while ESIM364 - up to 32 EWS2 devices.. The maximum wire-

less connection range is 150 meters (in open areas).

1. Package Content

1. EWS2. ...................................................................................qty. 1

2. 1,5V Alkaline AA Type Battery ....................................qty. 4

3. User manual ......................................................................qty. 1

2. Technical Speciﬁcations

2.1 Electrical & Mechanical Characteristics

Battery Type 1,5V Alkaline AA type

Number of Batteries 4

Battery Operation Time ~18 months*

Wireless Transmitter-Receiver Frequency 868 Mhz

Range of Operating Temperatures -30...+55ºC

Dimensions 201 x 140 x 36 mm

Wireless Communication Range Up to 30 meters in premises; up to 150 meters in open areas

Compatible with Alarm Systems ELDES Wireless

* This operation time might vary in dierence conditions.

2.2 Main Unit, LED & Connector Functionality

RESET Button for restoring default parameters

+ / - Battery slots

LED indicators Visual alarm indication

Tamper Tamper button contacts

Bell+ Positive siren speaker contact

Bell- Negative siren speaker contact

RESET

TAMPER

+ -

BELL

BATTERY + -

+-+-

+ - BATTERY

BATTERY BATTERY

Fig. No. 1

USER MANUAL EWS2 V2.1

3. Installation

1. Open EWS2 enclosure.

Remove the small blue lid located on the front side of the enclosure by pulling the lid up. (see Fig. No. 2).

Unscrew the front side of the enclosure (see Fig. No. 3).

Detach the front side of the enclosure by pulling the front side up (see Fig. No. 4).

Fig. No. 2

Fig. No. 3

Fig. No. 4

2. Once the enclosure is opened, remove the plastic tab inserted between one of the battery terminal and

battery slot contact (see Fig. No. 5).

3. Fix the siren on the wall using the screws (see Fig. No. 6).

4. Close EWS2 enclosure (see Fig. No. 4, Fig. No. 3, Fig. No. 2)

5. Bind the device to the alarm system using ELDES Conﬁguration Tool software. Open Wireless Device Management section and

enter a 8-digit wireless device ID located on the EWS2 enclosure and press Add button (see Fig. No. 7). The device can also be bind

by sending a corresponding command via SMS message. For more details, please, refer to the software‘s HELP section and ELDES

alarm system installation manual.

Fig. No. 5

Fig. No. 6

Fig. No. 7

BAT TERY

+ -

+- +-

+ -

BAT TERY

BAT TERY BATTERY

USER MANUAL EWS2 V2.1

6. Upon the successful binding process, EWS2 device icon becomes visible in Wireless Device section as well as Battery Level and

Signal Level. If attempt to bind is unsuccessful, try to move EWS2 closer to the alarm system device and bind anew.

7. EWS2 siren is ready for use.

NOTE: If you are unable to bind the wireless device, please, restore the parameters of the wireless device to default and try again.

See chapter 6. Restoring Default Parameters for more details.

4. EWS2 Zone, PGM Output & Tamper

Upon successful EWS2 outdoor siren binding process,the system adds 1 wireless Instant zone and 1 wireless Siren PGM output. The

wireless zone is intended for EWS2 tamper control and the wireless PGM output is for siren control.

In case of tamper violation, the alarm is caused regardless of system being armed or disarmed. There are 2 ways to detect tamper

violation on EWS2:

• By tamper button. EWS2 has a built-in tamper button intended for monitoring the enclosure status. Once the enclosure

of EWS2 is illegally opened, the tamper button becomes unpressed. This action is followed by alarm which is sent by SMS

message and phone call to the user (-s) by default. The SMS message contains the violated tamper number.

• By wireless connection loss. The wireless connection loss between EWS2 and ELDES alarm system leads to alarm. The sys-

tem identies this event as a tamper violation and sends alarm by SMS message and phone call to the user (-s) by default.

The SMS message contains the violated tamper number and a star * character indicating wireless connection loss as a tamper

alarm cause.

ATTENTION: The tamper will not operate if the wireless zone is disabled.

5. Battery Replacement

1. Open EWS2 enclosure.

2. Remove all 4 old batteries from the battery slots.

3. Postition the 4 new 1,5V alkaline AA type batteries according to the appropriate battery slot positive/negative terminals indicated

on the PCB (printed-circuit-board) of EWS2

4. Insert the batteries into the battery slots.

5. Batteries replaced.

See chapter 3. Installation for more details.

ATTENTION: Only 1,5V Alkaline AA type batteries can be used. Install only new, high quality and unexpired batteries. Do not mix

the old batteries with the new ones.

ATTENTION: At least 1 battery must be removed if the device is not in use.

ATTENTION: In order to avoid re or explosion hazards, the system must be used only with approved battery. Special care must

be taken when connecting positive and negative battery terminals. Dispose old batteries only into special collection sites. Do not

charge, disassemble, heat or incinerate old batteries.

NOTE: The system sends an SMS message to a preset User 1 as soon as the battery level runs below 5%.

NOTE: The battery status can be monitored in real-time using ELDES Conguration Tool software.

6. Restoring Default Parameters

1. Remove one battery from EWS2.

2. Press and hold the RESET button.

3. Insert the battery back to EWS2.

4. Hold the RESET button until LED indicator starts blinking.

5. Release the RESET button.

6. Parameters reset to default.

7. Additional Information

Limited Liability

The buyer must agree that the system will reduce the risk of re, theft, burglary or other dangers but does not guarantee against such

events.“ELDES UAB” will not take any responsibility regarding personal or property or revenue loss while using the system. “ELDES

UAB” liability according to local laws does not exceed value of the purchased system. “ELDES UAB” is not aliated with any of the

Internet providers therefore is not responsible for the quality of Internet service.

Manufacturer Warranty

This device carries a 24-month warranty by the manufacturer “ELDES UAB”. Warranty period starts from the day the system has been

purchased by the end user. The warranty is valid only if the system has been used as intended, following all guidelines listed in the

manual and within specied operating conditions. Receipt must be kept as a proof of purchase date. The warranty is voided if the

system has been exposed to mechanical impact, chemicals, high humidity, uids, corrosive and hazardous environment or other

force majeure factors.

Safety instructions

Please read and follow these safety guidelines in order to maintain safety of operators and people around:

• DO NOT use the system where it can be interfere with other devices and cause any potential danger.

• DO NOT use the system with medical devices.

• DO NOT use the system in hazardous environment.

• DO NOT expose the system to high humidity, chemical environment or mechanical impacts.

• DO NOT attempt to personally repair the system.

The WEEE (Waste Electrical and Electronic Equipment) marking on this product (see left) or its documentation indicates

that the product must not be disposed of together with household waste. To prevent possible harm to human health

and/or the environment, the product must be disposed on in an approved and environmentally safe recycling process.

For further information on how to dispose of this product correctly, contact the system supplier, or the local authority

responsible for waste disposal in your area.

USER MANUAL EWS2 V2.1

It is not allowed to copy and distribute information in this document or pass to a third party without advanced written

authorization by “ELDES UAB”. “ELDES UAB” reserves the right to update or modify this document and/or related products

without a warning. Hereby, “ELDES UAB” declares that this wireless outdoor siren EWS2 is in compliance with the essential

requirements and other relevant provisions of Directive 1999/5/EC. The declaration of conformity may be consulted at

www.eldes.lt

Vartotojo vadovas v2.1

Suderinama su:

• ESIM264 v7.11.08 ir naujesne + EWT1 v16.14 ir naujesne.

• ESIM364 visomis versijomis.

• EPIR v05.05.04 ir naujesne + EWT2 v16.14 ir naujesne.

• EPIR2 visomis versijomis.

Pagrindinės savybės:

• Garsinė aliarmo indikacija įmontuotu garsiakalbiu.

• Vaizdinė aliarmo indikacija įmontuotais LED indikatoriais.

• Darbo temperatūros diapazonas: -30...+55oC.

EWS2 yra belaidis įrenginys su įmontuotu aliarmo garsiakalbiu ir LED indikatoriais. Ši sirena yra pritaikyta montavimui lauke ir jungiama

prie ELDES belaidžių apsaugos sistemų, aktyvavus belaidį ryšį. Tai galima atlikti siunčiant SMS žinutę arba naudojantis ELDES Congura-

tion Tool programine įranga. Sėkmingai prijungus EWS2 sireną, sistema sukuria vieną belaidę zoną ir vieną belaidį PGM išėjimą. Aliarmo

metu sirena skleidžia garsą 1 minutę. Šio parametro kongūravimas EW2 sirenai yra išjungtas dėl baterijos energijos taupymo.

ESIM264, EPIR ir EPIR2 apsaugos sistemos palaiko iki 16 EWS2 įrenginių, ESIM364 - iki 32 EWS2 įrenginių. Maksimalus atstumas belai-

džiam ryšiui – iki 150 metrų (atvirose erdvėse).

1. Pakuotės sudėtis

1. EWS2 ....................................................................................1 vnt.

2. 1,5V Alkaline AA tipo baterija ....................................4 vnt.

3. Vartotojo vadovas ...........................................................1 vnt.

2 Techninė speciﬁkacija

2.1 Elektrinės ir mechaninės charakteristikos

Baterijos tipas 1,5V Alkaline AA

Baterijų skaičius 4

Baterijų veikimo trukmė ~18 mėn.*

Belaidžio ryšio dažnis 868 Mhz

Darbo temperatūros diapazonas -30...+55ºC

Matmenys 201 x 140 x 36 mm

Belaidžio ryšio atstumas Iki 30 metrų patalpose; iki 150 metrų atvirose erdvėse

Suderinamumas su apsaugos sistemomis ELDES Wireless

* Šis laikotarpis gali skirtis atsižvelgiant į naudojimo sąlygas.

2.2 Pagrindinių mazgų, LED indikatorių ir kontaktų paskirtis

RESET Gamyklinės kongūracijos atstatymo mygtukas

+ / - Baterijų lizdai

LED indicators Vaizdinė aliarmo indikacija

Tamper Tamperio mygtuko kontaktai

Bell+ Teigiamas aliarmo garsiakalbio kontaktas

Bell- Neigiamas aliarmo garsiakalbio kontaktas

RESET

TAMPER

+ -

BELL

BATTERY + -

+-+-

+ - BATTERY

BATTERY BATTERY

1 pav.

VARTOTOJO VADOVAS EWS2 V2.1

3. Instaliavimas

1. Atidarykite EWS2 korpusą.

Stumdami į viršų, nuimkite mažą mėlyną dangtelį, esantį ant priekinės korpuso dalies. (žr. 2 pav.).

Atsukite varžtą, esantį priekinėje korpuso dalyje. (žr. 3 pav.).

Nuimkite korpuso priekinę dalį, keldami ją į viršų. (žr. 4 pav.).

2 pav.

3 pav.

4 pav.

2. Atidarę korpusą, išimkite plastikinį tarpiklį, įterptą tarp vienos iš baterijų ir baterijos lizdo (žr. 5 pav.).

3. Varžtais pritvirtinkite sireną prie sienos (žr. 6 pav.).

4. Uždarykite EWS2 korpusą (žr. 4 pav., 3 pav., 2 pav.)

5. Aktyvuokite belaidį ryšį su ELDES apsaugos sistema, naudodami ELDES Conﬁguration Tool programinę įrangą. Atverkite Wireless

Device Management skyrių ir įveskite 8 skaitmenų belaidžio įrenginio ID numerį, esantį ant EWS2 korpuso (arba jo vidinėje pu-

sėje) ir paspauski te Add mygtuką (žr. 7 pav.). Belaidis ryšys taip pat gali būti aktyvuotas nusiuntus atitinkamą SMS žinutę. Plačiau

apie tai skaitykite programinės įrangos HELP skyriuje ir ELDES apsaugos sistemos instaliavimo vadove.

5 pav.

6 pav.

7 pav.

BAT TERY

+ -

+- +-

+ -

BAT TERY

BAT TERY BATTERY

Altri manuali per EWS2

Indice

Lingue:

Altri manuali Eldes Sistema di sicurezza

Manuali Sistema di sicurezza popolari di altre marche

Inner Range

Inner Range Concept 2000 Manuale utente

Climax

Climax Mobile Lite R32 Istruzioni per il montaggio

CADDX

CADDX NX-6 Manuale utente

FBII

FBII XL-31 Series Manuale utente

Johnson Controls

Johnson Controls PENN Connected PC10 Manuale utente

Aeotec

Aeotec Siren Gen5 Manuale utente

Blaupunkt

Blaupunkt SA 2700 Manuale utente

IDEAL

IDEAL Accenta Manuale del proprietario

AJAX

AJAX DoubleButton Manuale utente

Swann

Swann SW-P-MC2 Manuale utente

Ecolink

Ecolink Siren+Chime Manuale utente

Digital Monitoring Products

Digital Monitoring Products XR150 Manuale utente

EDM

EDM Solution 6+6 Wireless-AE Manuale utente

Highway Safety Group

Highway Safety Group EA401 Manuale utente

Siren

Siren LED GSM Manuale utente

Detection Systems

Detection Systems 7090i Istruzioni per il montaggio

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuale utente

Siemens

Siemens FDM273 Manuale utente