ElectrIQ DOGCAM720 Manuale utente
WIRELESS IP CAMERA
SETUP AND USER MANUAL
Thank you for choosing electriQ.
Please read this user manual before using this item and
keep it safe for future reference
.
Visit our page www.electriQ.co.ukfor our entire range of
electricals
IMPORTANT SAFETY INSTRUCTIONS
Read all instructions. All user guidelines must be
read before the device is used.
Retain the instructions for further use.
For indoor use only. Do not position the unit
where it would be subjected to extreme moisture,
temperature, or dust.
Do not use in bathrooms or other humid places.
There are no user maintainable parts, do not
attempt to disassemble or repair.
Do not place the device near a heat source, or
expose to direct sunlight.
INTRODUCTION
Thank you for purchasing an electriQ Wifi controlled device.
INSTALLATION OF APP
Before installation download the YOOSEE app either using the
QR codes below or searching in your chosen app store.
ANDROID IOS
REGISTER WITH THE APP
Once the app has loaded
select the option for Quick
Register.
You will then be prompted to
register using your mobile
phone number or email address,
verify the address / phone
number given and create a
password (Enter the password
in both boxes)
A verification code will be sent to
your phone or email which must
be input into the app to complete
registration.
The password must be at least 8 characters and contain letters
and numbers. Once your password and verification number
have been entered, press Confirm
Please note: When registering / logging in using your phone
number the 0 should be removed from the start of your phone
number. e.g. If your phone number is 07123456789, enter
7123456789.
LOG INTO THE APP
Enter your email address or phone
number (depending how you originally
registered) and password into the
main screen and press thelogin button
CONNECTING THE CAMERA TO YOUR WIRELESS
NETWORK
Ensure your camera and mobile are situated close to the router
so they both recieve a good WIFI signal.
Connect your phone to your 2.4ghz wireless network. (To
ensure your phone is connected to your router correctly it is
advisable to disable mobile data, and check access to the
internet using your phones browser)
Plug the camera into the mains
(ensuring it is still close to the
router).
Wait for around 30 seconds until the
camera starts to bleep (single bleep
at 10 second intervals)
If after 30 seconds the camera does
not start to bleep: Reset the camera by
inserting a pin into the RESET hole on
the underside of the camera for 5
seconds until the unit makes a noise.
Then leave for 30 seconds until the
camera bleeps.
Please note the camera can only be connected to a 2.4ghz
network. If your router is also able to operate at 5ghz
(Dualband), the 2.4ghz MUST be given a different name
(SSID) to the 5ghz network and the connection made to the
2.4ghz network only. Fursther details on changing the SSID
of your router are available from your ISP / Router
manufacturer.
Once the camera is bleeping, return to
the app on your phone and press the +
icon in the top right hand corner
Press the option to “Add new device”
Press the option for Fast
Networking.
Select your 2.4ghz WIFI network
from the drop down list and enter
the password for your network.
(This is usually found on a sticker
on the side or back of the router
unless it has been changed).
Press on the access point
created by the camera which
will be labelled “GM_AP_******”
The phone will then disconnect
from your wifi network, and will
connect to the network created
If the app is unable to create the
connection, it will bring up a message,
asking you to swap the internet
connection manually. To do this exit the
app, disconnect from your wifi network,
and connect to the hotspot created by
the camera which will be labelled
“GM_AP_******” before going back to
the app to continue setup.
When the camera bleeps to indicate it
has successfully connected, press the
blue Confirm button at the bottom
You will then receive the message
showing installaion was successful.
Press confirm to proceed to the main
viewing screen.
USING THE APP - OVERVIEW
ALL DEVICE SCREEN
1: Scan QR code from friend for
device sharing
2: Change the name of the
camera
3: Add a new camera
4: Share device with a friend /
create QR code
5: N/A
6: Playback from SD card in
camera
7: Camera Settings
8: List devices paired with App
9: Alarm Push Information
10: Access images and videos saved to phone.
11: App Settings
12: View Camera (See Below)
CAMERA VIEW
SCREEN
1: Return to All Device
Screen
2: Device Settings
3: Preset Position
Marker
4: Video Quality
5: Full Screen Mode
6: Record Video to
Phone
7: Intercom
8: Screenshot to
Phone
9: Speaker On/Off
1
2
3
4
5
6
7
8
9
10
11
12
1
2
3
4
5
6
7
8
9
While on the camera view screen you can pan and tilt the image
by sliding your finger across the image. A pinch action can also
be used to zoom in and out on the image.
ALL DEVICES SCREEN
SHARING THE DEVICE WITH FRIENDS AND FAMILY
Once your camera is set up it can be
shared using Button 4 on the All
Devices screen. This will create a QR
code which can then be scanned on
the other persons phone.
It will also create a web link that can
be emailed to a PC to allow access to
the camera through the CMS app.
To scan the code, they must log into
the app under their own user account,
and then press the buttd.n labelled as
1 on the All Devices screen to scan the
QR code you have create.
PLAYBACK FROM SD CARD
By pressing Button 6 on the All devices
screen you are able view videos that
have been recorded to the SD card
within the camera (Standard SD card
upto 32gb available seperately)
From the playback screen, select which video file you would like
to view, which will then load the playback screen with basic
controls.
Example
Indice
Altri manuali ElectrIQ Telecamera IP
