Electrorad 4 Zones RF Programmer Manuale utente

4 Zones RF Programmer

IMPORTANT!

Before starting work, the installer should carefully read this

Installation & Operation Manual, and make sure all instructions

contained therein are understood and observed.

The programmer should be mounted, operated and maintained by

specially trained personnel only. Personnel in the course of training

are only allowed to handle the product under the supervision of an

experienced fitter. Subject to observation of the above terms, the

manufacture shall assume the liability for the equipment as provided

by legal stipulations.

All instructions in this Installation & Operation manual should be

observed when working with the programmer. Any other application

shall not comply with the regulations. The manufacturer shall not be

liable in case of incompetent use of the programmer. Any

modifications and amendments are not allowed for safety reasons.

The maintenance may be performed by service installers approved

by the manufacturer only.

The functionality of the programmer depends on the model and

equipment. This installation leaflet is part of the product and has to

be obtained.

APPLICATION

The RF programmer is developed to control and manage by

program function the working mode of electric radiators.

The programmers have been designed for use in residential rooms,

office spaces and industrial facilities.

Verify that the installation complies with existing regulations before

operation to ensure proper use of the installation.

SAFETY INSTRUCTIONS

Before starting work disconnect power supply!

All installation and wiring work related to the thermostat must be

carried out only when de energized. The programmer should be

connected and commissioned by qualified personnel only. Make sure

to adhere to valid safety regulations.

The programmers are neither splash nor drip proof. Therefore,

they must be mounted at a dry place.

Do not interchange the connections of the sensors and the 230V

connections under any circumstances! Interchanging these

connections may result in life endangering electrical ha ards or the

destruction of the programmer, connected sensors and other

appliances.

Table of content

1 Presentation...................................................................4

1.1 Keyboard....................................................................5

1.2 Display........................................................................ 6

2 First Installation..............................................................7

2.1 Battery installation.......................................................7

2.2 Time and Date adjustment..........................................7

2.3 RF installation.............................................................8

2.3.1 RF Installation with thermostat receiver...................8

2.3.2 RF Installation with thermostat receiver (Digital Control).........10

e) On the programmer, press () button 3 times to return to the home

screen. 11

2.3.3 RF Installation with Control conductor receiver....12

2.3.4 RF installation check..............................................14

2.4 Getting Started..........................................................16

3 Working mode definition...............................................17

3.1 Manual mode Comfort ..............................................17

3.2 Manual mode, Reduced ..........................................17

3.3 Standby mode ..........................................................17

3.4 Automatic mode........................................................18

3.5 Zone Program ..........................................................18

3.6 Program Mode .........................................................19

3.7 Holiday mode ...........................................................24

3.8 Timer mode ..............................................................25

4 Special function...........................................................25

4.1 Keyboard lock Function ............................................25

4.2 Optional Input...........................................................26

5 Parameter’s menu........................................................26

6 Technical characteristics .............................................29

7 Troubleshooting & Solution .........................................30

8 Annexes (Built in Program description) .......................31

1 Presentation

4 zone digital programmer with LCD display specifically

designed to supervise the working mode of the electrical

radiators installation.

It will optimise energy consumption and increase comfort

levels.

Wiring & easy Installation.

“Easy program creation” function.

Weekly programmable by steps of 30min.

Temporary override function.

Anti freeze function.

Holiday mode function.

EEPROM non volatile memory.

2 AA batteries for 2 years operating life.

1 parameter menu, (User and Installer)

*In option

1 input for GSM control (secondary house…)

In order for the programmer to control the installed

electrical radiators, they must be in “Auto Mode” and the

Control conductor must not be connected but isolated.

1.1 Keyboard

( ) Back button to return to the previous menu.

(►+) Navigation button “right” in menu selection or plus

button for value edition.

(◄-) Navigation button “left” in menu selection or minus

button for value edition.

(OK) Validation button.

Backlight function:

Press this button (OK) to light up the backlight for

60 seconds.

(i) Main menu button.

1.2 Display

1. Operating mode menu (active mode is framed).

2. Key lock indicator

3. Installation Parameter menu.

4. Current day of the week (1 = Monday)

5. Current time or parameter title if “ ” is displayed.

6. Icon for program creation.

7. Room Temperature indicator.

8. Room temperature if “ ” is displayed. Parameter

value if “ ” is displayed.

9. RF transmission icon.

10. Program of the current day

(the current time bar flashes)

11. Zone status (Comfort, Reduced or Temporary override

function).

12. “Low Battery” indicator.

13. External option is activate.

2 First Installation

This section is a guide to set up the programmer for the

first time.

2.1 Battery installation

Open the backside cover and insert the 2 AA Alkaline

supplied batteries (or remove the small protection sticker if

the batteries are already installed in the compartment)

Close the cover.

Now adjust and configure the necessaries parameters.

2.2 Time and Date adjustment

Each time a value flashes, adjust it with the (◄-) and (►+)

buttons, once the value is chosen, validate it by pressing

the (OK) button. The programmer will jump automatically to

the next value.

To come back to the previous value, press the back button

( ).

List order of the time and date adjustments:

Time and day:

Adjustment of the hours

Adjustment of the minutes

Adjustment of the day (1 = Monday)

Date:

Adjustment of the day number (0 to 31).

Adjustment of the month number (01 to 12).

Adjustment of the year (Century).

Adjustment of the year

Press (OK) to valid the adjustments.

To access the time and date section while in normal

working mode, at any time, press and hold the (OK) button

for 2 seconds.

2.3 RF installation

2.3.1 RF Installation with thermostat receiver

a) Press the (OK) button to enter in the “init” (initialize)

mode on the programmer, then choose the zone which

needs to be configured by moving the frame cursor

(around number 1) with (◄-) and (►+) buttons on the

desired zone number, 1 to 4.

b) Once the zone is selected, press the (OK) button and

choose to use it with (◄-) and (►+) “Yes” or “no”,

By choosing “no” the zone will be not displayed on

the main screen, then choose another one.

By choosing “Yes” the following screen will be

displayed and the programmer will start to send the

radio configuration signal to the radiator controller.

c) On the radiator controller, press and hold the main

button for a few seconds until the green LED flashes.

Then release the button.

d) The radiator controller is now linked and ready to work

with the programmer.

Once the configuration between the radiator

controller and the programmer is made, repeat step (c)

to link all the radiator controllers, which are to be

connected to the same zone.

Repeat the step (b) to (d) to include more zones on

the installation.

e) On the programmer, select “End” with the button (►+)

and press (OK) to exit the parameter menu.

…

2.3.2 RF Installation with thermostat receiver

(Digital Control)

a) On the programmer, press and hold (8 secs) the ( )

button to enter in the “init” (initialize) mode, then press

the (OK) button twice to confirm the “init” mode. Now

choose the zone which needs to be configured by

moving the frame cursor (around number 1) with (◄-)

and (►+) buttons on the desired zone number, 1 to 4.

b) Once the zone is selected, press on the (OK) button

and choose it with (◄-) and (►+) “Yes” or “no”.

By choosing “no” the zone will be not displayed on

the main screen, then choose another one.

By choosing “Yes” the following screen will be

displayed and the programmer will start to send the

radio configuration signal to the radiator controller.

Indice

Manuali Scheda madre popolari di altre marche

DFI

DFI SD170 Manuale utente

ASROCK

ASROCK ROMED8-2T Manuale utente

Asus

Asus P2L97A Manuale utente

Winmate

Winmate IC70 Manuale utente

Asus

Asus MES-B Manuale utente

Grantech

Grantech SYS8F377VGGA-3OMN Manuale utente

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuale utente

Gigabyte

Gigabyte GA-9IVDT Manuale utente

Texas Instruments

Texas Instruments ADS8372EVM Manuale utente

Commell

Commell MS-C73 Manuale utente

IBT Technologies

IBT Technologies MB860 Manuale utente

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuale utente

Biostar

Biostar M7VIT Bravo Istruzioni per l'uso e l'installazione

Intel

Intel D33217CK Manuale utente

Asus

Asus F1A55-M LX PLUS R2.0 Manuale utente

EPC

EPC EPC9147C Manuale utente

Asus

Asus EX-B760M-V5 D4 Manuale utente

EPOX

EPOX MU-8KHA0010 Manuale utente