ELEVATE Jupiter Manuale utente

Jupiter EVM Getting Started Rev C01 : 05/17/2007

Jupiter EVM Getting Started

Rev C01 : 05/17/2007

Jupiter EVM Getting Started Rev C01 : 05/17/2007

Table of Contents

1Introduction..........................................................................................................................................................4

1.1 Unpacking - Jupiter EVM Contents ..........................................................................................................4

1.2 Recommended Test and Measurement Setup...........................................................................................5

1.2.1 Power Supply.........................................................................................................................................5

1.2.2 PC Controller.........................................................................................................................................5

1.2.3 DMM or Source Measurement Unit ......................................................................................................5

1.3 Software Installation ...................................................................................................................................6

1.3.1 Jupiter EVM UIP Installation ................................................................................................................6

1.3.2 Parallel Port (ParPort2K) Installation....................................................................................................6

1.3.3 Reboot Machine.....................................................................................................................................6

1.3.4 Launching the Elevate Semiconductor Program....................................................................................6

1.3.5 Software Un-Installation........................................................................................................................6

2Getting Started......................................................................................................................................................7

2.1 Caution .........................................................................................................................................................7

2.2 Jupiter Loadboard Rev B versus Rev C+..................................................................................................7

2.3 Quick Start Instructions..............................................................................................................................7

2.4 Default Configuration Setup Options ........................................................................................................9

2.4.1 Remote Sense Option...........................................................................................................................10

2.4.2 General DPS Configurations................................................................................................................10

2.4.3 Ganging (Merging) Configuration.......................................................................................................11

2.5 Jupiter Loadboard Jumper Definitions...................................................................................................12

2.6 Motherboard Jumper and SMA Definition.............................................................................................13

2.7 Jupiter EVM Menu and Dialog Boxes.....................................................................................................14

3Jupiter EVM Loadboard Detailed Description..................................................................................................18

3.1 Capacitor and Resistor Network Definitions...........................................................................................19

3.2 ADC and Analog Mux...............................................................................................................................20

3.3 Jupiter Loadboard Controller..................................................................................................................21

4Document Revision History................................................................................................................................22

Jupiter EVM Getting Started Rev C01 : 05/17/2007

List of Figures

Figure 1: Installation Directory Structure......................................................................................................6

Figure 2: Expected Current Readings..........................................................................................................8

Figure 3: Jupiter EVM Simplified Block Diagram.......................................................................................10

Figure 4: Jupiter EVM Ganging Configuration Simplified Block Diagram..................................................11

Figure 5: Device Config Menu Options......................................................................................................14

Figure 6: Jupiter Configuration Dialog Box................................................................................................15

Figure 7: Jupiter DC Levels Dialog Box.....................................................................................................16

Figure 8: Jupiter DAC Configuration Dialog Box .......................................................................................16

Figure 9: Jupiter Central Register Dialog Box............................................................................................17

Figure 10: Jupiter EVM Detailed Block Diagram........................................................................................18

Figure 11: Jupiter EVM Capacitor/Resistor Network Block Diagram.........................................................19

Figure 12: Controller Section Detailed Block Diagram ..............................................................................21

List of Tables

Table 1: Jupiter EVM Contents.....................................................................................................................4

Table 2: Power Supply Requirements .........................................................................................................5

Table 3: Jupiter Default Configuration Options............................................................................................9

Table 4: Jupiter Loadboard Jumper Definitions.........................................................................................12

Table 5: Motherboard SMA and Jumper Definitions (Jupiter Input Signals)..............................................13

Table 6: Motherboard SMA Definitions (Jupiter Output Signals)...............................................................13

Table 7: Capacitor Network Definitions......................................................................................................19

Table 8: Resistor Network Definitions........................................................................................................19

Table 9: FVMI Analog Mux – VINPOS(A) & VINNEG(A) Mapping.............................................................20

Table 10: Jupiter Loadboard Analog Mux Definitions - LB_AMUX Mapping.............................................20

Jupiter EVM Getting Started Rev C01 : 05/17/2007

1 Introduction

Congratulations on your purchase of a Elevate Semiconductor Jupiter EVM evaluation system. You will

find that it serves as an invaluable development platform to help get your product to market in the shortest

possible time. The Jupiter EVM and Graphical User Interface (GUI) allow the customer to demonstrate

and evaluate the Jupiter performance and functionality.

This document provides the instructions to install, setup, and operate the Jupiter EVM. Refer to the

Elevate Semiconductor EVM User’s Guide for a detailed description of the EVM system.

1.1 Unpacking - Jupiter EVM Contents

Please check the contents of the Jupiter EVM shipping carton to make sure you have received all of the

items listed in Table 1. The system is already configured for the best setup, except for connections to the

power supply, PC controller, and test equipment.

Table 1: Jupiter EVM Contents

Qty Description

1 ea. Jupiter EVM System (3 boards)

1 ea. Jupiter EVM Getting Started (this document)

1 ea. CD Contents List

1 ea. Elevate Semiconductor User Interface Program Installation CD

1 ea. DB25M-DB25M, 6 Foot Parallel Port Cable

Jupiter EVM Getting Started Rev C01 : 05/17/2007

1.2 Recommended Test and Measurement Setup

1.2.1 Power Supply

Table 2 provides the required power supplies and current rating. The power supplies are connected

using standard banana plugs. The customer needs to provide the power supply cables.

It is recommended to use a triple supply to control the EVM supplies. This allows the 3 EVM supplies to

be turned on at the same time. However, if this is not feasible, then the supplies should be enabled in the

following sequence. Power down should be performed in the reverse order.

1. +20V

2. -15V

3. +5V

The Jupiter VCC, VCC_OUT and VEE are gated using an Opto-FET switch on the loadboard so it is safe

to set and enable the Jupiter supplies before powering up the EVM and running the software.

Table 2: Power Supply Requirements

Module Supply Current Rating

Motherboard +20V

(1)

0.5 A

Motherboard +5V 0.5 A

Motherboard -15V 0.5 A

Jupiter VCC/VCC_OUT +16V

(

)

2.0 A

(

)

Jupiter VEE -5V

(

)

2.0 A

(

)

Notes:

1) The EVM +20V could also be used as the Jupiter VCC

2) Once the EVM operation is verified, the customer can adjust the VCC, VCCO, VEE supplies

3) The Jupiter VCC – VEE voltage should not exceed 34V. Refer to the ABS max section in the

datasheet.

4) The VCC, VCC_OUT, and VEE current requirements are assuming a Master and Slave device is

present. If only the Master is present, then a 1 Amp supply is adequate. The program does not

have the ability to measure the Jupiter VCC and VEE currents

1.2.2 PC Controller

To use the Jupiter EVM User Interface Program (UIP), a PC with the following configuration is required:

Win98, Win2000, WinNT 4.0+, or Win XP

Parallel/Printer Port – 25-pin female connector (a parallel port cable is provided)

1.2.3 DMM or Source Measurement Unit

Voltage and/or Current Meter

Voltage and/or Current Source

Jupiter EVM Getting Started Rev C01 : 05/17/2007

1.3 Software Installation

There are 2 steps to install the Jupiter EVM demonstration program.

1. Install the Jupiter EVM UIP from the CD-ROM.

2. Install the parallel port driver (ParPort2k).

Figure 1 illustrates the default directory structure. The user may change the <root dir> during the

installation.

Figure 1: Installation Directory Structure

<Root Dir>\Planet ATE\EVM\Documents (several folders)

EVM GUI

ParPort2k

1.3.1 Jupiter EVM UIP Installation

To install the Jupiter EVM software package, run the SETUP program on the distribution CD and follow

the prompts. The PlanetATE.exe executable will be installed in the EVM GUI sub-directory. In addition,

a short cut will be installed onto the desktop and in the Start->Programs folder. The Start->Programs

folder also contains links to the different product datasheets, EVM User’s Guide, and documentation

folder.

1.3.2 Parallel Port (ParPort2K) Installation

To install the ParPort2K parallel port driver, run the setup.exe from the ParPort2k sub-directory after the

main installation is complete and click the Install button. For WinNT users, the user must have

administration rights.

Note: ParPort2k is a copyright of Zeecube Software.

1.3.3 Reboot Machine

After the Jupiter EVM and Parallel Port software is installed, it is recommended to re-boot the machine.

1.3.4 Launching the Elevate Semiconductor Program

The user can launch the Elevate Semiconductor GUI from the Desktop, Start->Programs folder, or

EVM GUI sub-directory.

1.3.5 Software Un-Installation

The Elevate Semiconductor demonstration program may be un-installed using the Add/Remove

Program from the Windows Control Panel.

Jupiter EVM Getting Started Rev C01 : 05/17/2007

2 Getting Started

The Jupiter EVM is shipped in a pre-configured state that allows a customer to evaluate the DPS Force

Voltage (FV), Force Current (FI), and Ganging.

Note: Any external equipment providing digital signals into the Jupiter device should only be enabled

after the Jupiter EVM is enabled. Also, the external equipment should be disabled prior to disabling the

Jupiter EVM.

2.1 Caution

Jupiter is a high voltage DUT Power Supply (DPS) capable of delivering several amps of current.

Configuring the Jupiter device and EVM into an extremely high power condition could cause permanent

damage to the Jupiter device, EVM components and/or external equipment.

2.2 Jupiter Loadboard Rev B versus Rev C+

There are 2 different loadboard revisions; Rev B and Rev C+. This document focuses on the Rev C+

loadboard; refer to Section 3 for details. Refer to previous document revisions when using the Rev B

loadboard. The software supports both loadboard revisions.

2.3 Quick Start Instructions

1. Disable external power supply

2. Connect the power supplies cables (not provided) from the power supply to the Elevate

Semiconductor EVM Motherboard and Jupiter loadboard; refer to Figure 3.

3. Connect the parallel cable (provided) from the PC to J2 on the Octal FVMI board.

4. Connect the EVM to any external equipment; refer to Section 2.4.

5. Setup Motherboard Jumpers; refer to Section 2.5

6. Set external power supply voltages and current limits.

7. Enable external power supply.

8. Run the Elevate Semiconductor GUI software; refer to Section 1.3.4 for details.

9. At the Force Voltage – Measure Current dialog box (refer to Figure 2 below):

a. Select the EVM Setup option based on the desired configuration, see Section 2.4

b. Select the Enable Supplies check box

c. Hit the Apply button to power up the Jupiter device.

d. The software will also measure the current consumption. Figure 2 illustrates the expected

current readings.

10. At this point, the Jupiter should be outputting the desired signal.

Jupiter EVM Getting Started Rev C01 : 05/17/2007

Figure 2: Expected Current Readings

The Reset System will put the EVM and Jupiter device into the default state. The Reset System should

be issued whenever the power supply is powered OFF then ON. The Reset System is automatically

performed when the program is initially launched.

Jupiter EVM Getting Started Rev C01 : 05/17/2007

2.4 Default Configuration Setup Options

The EVM has several default options for configuring for device and loadboard.

Table 3: Jupiter Default Configuration Options

Mode See Section # Brief Description

Hardware Reset N/A All registers default to the hardware default state.

Note: Output is always present on FORCE_A. Sel-Force=GND

Three-State (High-Z) N/A Puts DPS in three-state (high-Z). Opens all switches.

Note: Output is always present on FORCE_A. Sel-Force=GND

FV out FORCE-A

with Alarms 2.4.2 FV mode with Alarms enabled. Connect DPS output to

TEST_NODE via FORCE_A. VF0= 3.0V.

FV out FORCE-B

with Alarms 2.4.2

(default) FV mode with Alarms enabled. Connect DPS output to

TEST_NODE via FORCE_B. VF0= 3.0V.

Note: Output is always present on FORCE_A.

Ganging 2.4.3 Master (U1) placed into FV mode with Remote Sense.

Slave (U2) placed into FI mode using Master’s MI as reference.

Master/Slave use FORCE-B output connected to TEST_NODE.

Alarms are enabled. IR=512mA.

External DAC

(FV Mode) 2.4.2 Bypass the internal DAC and use the FVMI resources as inputs

into Gang2/Gang3. FV mode with Alarms enabled. Connect

DPS output to TEST_NODE via FORCE_B.

VFORCE2=1.5V, VFORCE=0V

Default: applies to all software configurations

Loadboard: Jumpers E2, E4, and E7 are installed

Jupiter: CPU-En = 1 and Local-Sense* = 1

Jupiter: Monitor Enabled, Sel-MV = MV

Jupiter: Iclamps = +/-700mA. Vclamps = 14V/-2V (but disabled)

Jupiter: COMP_A, COMP_B, and External CAP_SR connected and SR-Adj = 15

FORCE-A default configuration

Loadboard: FORCE_A is connected to TEST_NODE (Con-FA-TN)

Loadboard: SENSE pin is connected to TEST_NODE (Con-Sense-TN)

Jupiter: Sel-FB (feedback) = FORCE_A

Jupiter: Con-FA-FB switch = open

FORCE-B default configuration

Loadboard: FORCE_B is connected to TEST_NODE (Con-FB-TN)

Loadboard: SENSE pin is connected to TEST_NODE (Con-Sense-TN)

Jupiter: Sel-FB (feedback) = FORCE_B

Jupiter: Con-FA-FB switch = closed

FORCE-A/B with Alarms configuration

The device is configured to automatically shut down if an Over Temperature alarm fault is detected

Over Tempature enabled and set to code=4 (approximately 116’C)

IClamp Alarm enabled but not routed to Global Alarm (won’t shut down DPS)

Sel-Con-FA-FB = 1 (use On-Chip-En)

Sel-DPS-En = 1 (use Global-Alarm)

For FORCE-A, the DPS_EN is used to control the FORCE_A to TEST_NODE relay

Note: the alarms are setup to latch the fault condition. To remove the fault, issue the appropriate ‘reset’

in the Jupiter Configuration dialog box. Use the LEDs or ReadBack to determine which alarm tripped.

Jupiter EVM Getting Started Rev C01 : 05/17/2007

2.4.1 Remote Sense Option

Extreme caution should be used when configuring the feedback (SENSE) path to ensure the DPS does

not become open loop. The Jupiter device has 2 output pin options (FORCE-A or FORCE-B) and internal

mux options. The Loadboard has several jumper and switch options to directly connect to the

FORCE-A/B pin or to connect to the TEST_NODE.

Note: To put the Jupiter device in remote sense, after selecting the FORCE-A or FORCE-B configuration

option then change the ‘CPU-Sel-FB’ option to SENSE

2.4.2 General DPS Configurations

Figure 3 illustrates the recommended configuration for Jupiter EVM evaluation. After the configuration is

completed, use the Jupiter->DPS Levels dialog box the change the Jupiter output levels. Use the

Jupiter Loadboard dialog box to connect to the on-board resistor network and/or capacitive load.

For the External DAC mode, jumper E1 must be installed. The VFORCE2 voltage is connected to the

Gang2 (V+) input and the VFORCE voltage is connected to the Gang3 (V-) input. Use the

EVM->FVMI (DPS) Config dialog box to change the VFORCE and VFORCE2 voltage values.

If using an external measurement unit (MU), the MU should be configured in the opposite mode as

Jupiter.

Jupiter MU

FVMI FIMV

FIMV FVMI

Important note: the FORCE_A is always connected to the high power op-amp stage and can not be put

into HiZ (disabled). Therefore when using the FORCE_A option, it is recommended to connect any load

to the TEST_NODE SMA so the Con-FA-TN relay can be opened in the event of an alarm condition.

Figure 3: Jupiter EVM Simplified Block Diagram

Motherboard

Jupiter Load Board

J2 (FVMI)

Parallel

Cable

EVM

Power

Supply

Jupiter

DMM

Measurement

Unit

MONITOR

FORCE_A

SENSE

FORCE_A

VCC

VCCOUT

VEE

+20V (BN1)

-15V (BN2)

+5V (BN3)

GND (BN4) LEDs

FORCE_B

SENSE

FORCE_B

TEST_NODE

Rnet

Cloads

DPS_EN

Jupiter

Power

Supply

E1 (VFORCE)

Indice

Altri manuali ELEVATE Scheda madre

ELEVATE

ELEVATE Triton/ISL55185 EVM Manuale utente

ELEVATE

ELEVATE ISL55180 EVM Manuale utente

Manuali Scheda madre popolari di altre marche

DFI

DFI SD170 Manuale utente

ASROCK

ASROCK ROMED8-2T Manuale utente

Asus

Asus P2L97A Manuale utente

Winmate

Winmate IC70 Manuale utente

Asus

Asus MES-B Manuale utente

Grantech

Grantech SYS8F377VGGA-3OMN Manuale utente

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuale utente

Gigabyte

Gigabyte GA-9IVDT Manuale utente

Texas Instruments

Texas Instruments ADS8372EVM Manuale utente

Commell

Commell MS-C73 Manuale utente

IBT Technologies

IBT Technologies MB860 Manuale utente

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuale utente

Biostar

Biostar M7VIT Bravo Istruzioni per l'uso e l'installazione

Intel

Intel D33217CK Manuale utente

Asus

Asus F1A55-M LX PLUS R2.0 Manuale utente

EPC

EPC EPC9147C Manuale utente

Asus

Asus EX-B760M-V5 D4 Manuale utente

EPOX

EPOX MU-8KHA0010 Manuale utente