Elmdene G240xNU Manuale utente

27.6V

WITCH

ODE

OWER

UPPLY

ODULES

odel

G240x U

Where ‘x’ is max load current: 1A, 2A, 3A or 5A.

EATURES

High efficiency cost effective power supply ideal for use in Fire, Access Control and General Security

applications. Featuring a regulated 27.6Vdc output supplying continuous full rated current to load and up to

an additional 0.5A for charging 2 x 12V standby batteries. The universal mains input voltage enables the

power supply to be used across a wide geographical area. The highly efficient switch mode design ensures

low operating costs while generating less heat. The modular construction simplifies maintenance.

•Universal mains input voltage 90-264vac

•Additional 0.5A to charge 2 x 12V standby batteries

•High efficiency electronics for reduced running costs and lower

operating temperatures

•Continuous full rated current to load

•Modular construction for ease of maintenance & installation

•Installer safe design with all high voltage electronics fully shrouded

•Reverse battery connection protection

•Full electronic short circuit and overload protection on load output

•Mains transient protection circuit

•Green Mains present LED

•Yellow Fault LED

Elmdene International Ltd

Tel: +44 (0)23 9269 6638

3 Keel Close, Interchange Park, Fax: +44 (0)23 9266 0483

Portsmouth, Hampshire, PO3 5QD, UK 

Web: www.elmdene.co.uk

PECIFICATIO

Input Specification

Voltage (rat

ed)

100

240Vac

Voltage (operating)

264Vac

Frequency

60Hz

x Current

See Model Specification Table

Mains Input Fuse

See Model Specification Table

Max standby Power

0.8W (n

o load

and no battery

connected)

Output Specification

Voltage

27.0 – 28.0Vdc (27.6vdc nominal) on mains power

21.0 – 24.7Vdc on battery standby

Max load current

See Model Specification Table

Ripple

0 mV pk

pk max

Load output Fuse

See Model Specification Table below

Overload

Electronic shutdown until overload or short ci

rcuit removed

(under mains power only)

Local Indicators

MAINS LED (Green)

Mains present

FAULT LED (

Yellow

)

Fault present: Output or battery fuse fail (requires load &

battery to be connected), loss of mains, output short circuit

or low output voltage.

Standby Batteries

Battery Type

2 x 12V Valve Regulated Lead Acid

Battery Charging Fuse protection

F630mA 20mm glass

Mechanical

Model G2401 U G2402 U G2403 U / G2405 U

Module

Dimensions

w x h x d (mm / external) 134 x 84 x 42 152 x 106 x 52 157 x 143 x 55

Recommended Batteries 2 x 12V NP7 or NP17

Weight

G2401 U G2402 U G2403 U / G2405 U

240g 280g 650g

Environmental

Temperature -10 to +40°C (operating) 95% RH non-condensing

-20 to +80°C (storage)

Connections

+O/P +ve voltage O/P to load equipment

-O/P -ve voltage O/P to load equipment

+BATT Red lead to standby battery 1

-BATT Black lead to standby battery 2

0m m

20mm

0m m

20mm

0m m

20mm

PERATIO

This unit is intended for use by Service Personnel only - There are NO USER SERVICEABLE parts inside.

The Green Mains LED will be illuminated whilst the mains supply is present. In the event of a fault condition,

the Yellow Fault LED will be illuminated.

STALLATIO A D

-U

This unit is only suitable for installation as permanently connected equipment. The PSU is NOT SUITABLE for

external installation. EQUIPMENT MUST BE EARTHED. Before installation, ensure that external disconnect

device is OFF. The PSU should be installed according to all relevant safety regulations applicable to the

application.

Enclosure and Mounting

This power supply module has high voltage present and is for use by Service Personnel only. This power

supply module MUST be securely mounted within a robust enclosure having suitable means to prevent

unintentional access to the module. Suitable notices must be affixed to the outside of the enclosure to warn

of high voltages present internally.

Mounting the module

1) Mount securely in correct orientation allowing minimum clearance of 20mm all round – see diagrams

below.

2) The G2401NU and G2402NU modules have the option of either being DIN rail mounted (using the

integrated DIN rail mount) or by using appropriate fixings using the four available mounting lugs. The

G2403NU and G2405NU modules are fixed using the three available mounting points.

Mains Power Up

3) Attach correctly rated mains cable (minimum 0.5mm

[3A], 300/500Vac) and secure in enclosure using

cable ties.

4) Apply mains power. Check for 27.6Vdc on load outputs. Check Green Mains LED is on.

5) Disconnect mains power.

Load Output

6) Attach correctly rated load cable and secure in enclosure using cable ties. Note polarity.

7) Apply mains power. Check green Mains LED is on.

8) Verify load is operating correctly.

9) Disconnect mains power.

G2401NU

G2402NU

G2403NU & G2405NU

E L N

L E N

STALLATIO A D

-U

CO TI UED

Standby Battery - OTE: Ensure batteries fitted to this unit are in good condition

10) Connect battery to terminal block using minimum 32/0.2 (1.0mm

CSA) stranded wire.

OTE: ensure correct polarity of battery connections.

Maximum recommended total battery lead length = 500mm

11) Apply mains power. Check Green Mains LED is on.

12) Check there is no fault indication on Yellow LED.

13) Disconnect mains power. Check that the batteries continue to supply voltage and current to the load.

The Green LED should be off.

OTE: Batteries must have sufficient charge to supply the load

14) Reconnect mains power. Green LED should be on.

15) Remove Load fuse and check Yellow Fault LED is on.

16) Replace Load fuse. Check Yellow Fault LED is off.

Module Dimensions

124

114

40,5

G2401N

128

42,4

152

106

G2402N

157

128 7,5

128

42,4

19 60

56,5

135

143

G2403N & G2405N

AI TE A CE

There is no regular maintenance required of the PSU other than periodic testing and replacement of the

standby batteries. Reference should be made to the battery manufacturer’s documentation to determine

typical/expected battery life with a view to periodic replacement of the battery.

If the output of the PSU fails the cause of the failure should be investigated e.g. short circuit load. The fault

should be rectified before restoring power to the PSU. The fuses may need to be replaced. Ensure the

correct fuse rating and type is used.

Model Specification Table G2401NU G2402NU G2403NU G2405NU

Output Current 1A 2A 3A 5A

Battery Charge Current 0.5A 0.5A 0.5A 0.5A

Mains LED (Green) √ √ √ √

Fault LED (Yellow) √ √ √ √

Max Mains Input Current (at 90Vac) 1.0A 1.3A 1.4A 2.0A

F1 - Mains Input Fuse (20mm HRC) T2.0A T2.0A T3.15A T3.15A

F2 - Output Fuse (20mm) F1.0A F2.0A F3.15A F5.0A

F3 - Battery Fuse (20mm) 630mA 630mA 630mA 630mA

This p ge h s been left bl nk intention lly.

OMPLIA CE

This product meets the essential requirements of the following EU Directives:

Low Voltage: 2014/35/EU

EMC: 2014/30/EU

RoHS2: 2011/65/EU

WEEE: 2012/19/EU

ISPOSAL OF

RODUCT AT

D OF

IFE

This product falls within the scope of EU Directives 2012/19/EU Waste Electrical and Electronic Equipment

(WEEE) and 2013/56/EU (Battery). At the end of life, the product must be separated from the domestic

waste stream and disposed via an appropriate approved WEEE disposal route in accordance with all national

and local regulations.

Before disposal of the product, the standby battery must be removed and disposed separately via an

appropriate approved battery disposal route in accordance with all national and local regulations. Package

used batteries safely for onward transport to your supplier, collection point or disposal facility.

See Specification for battery type information. The battery is marked with the crossed out wheelie bin

symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg).

For more information see: www.recyclethis.info

Caution: Risk of explosion if b ttery is repl ced by n incorrect type.

Dispose of used b tteries ccording to the b ttery m nuf cturer’s

instructions nd ll loc l nd n tion l regul tions.

The p ck ging supplied with this product m y be recycled.

Ple se dispose of p ck ging ccordingly.

Indice

Altri manuali Elmdene Unità di controllo

Elmdene

Elmdene G240 BMU Series Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente