Ember GW01 Manuale utente
GW01 GATEWAY INSTRUCTIONS
www.ephcontrols.com/ember
emberapp.ephcontrols.com
2
Welcome
Thank you for choosing EMBER by EPH Controls. We hope you
enjoy using it as much as we did developing it!
Controlling your heating anywhere, anytime is only a few simple
steps away.
In this booklet, we will provide a step by step guide to setting up
the EMBER heating control app and its associated hardware.
Again, thank you for choosing EMBER.
3
Index
Page 4 Getting started
(Router requirements/Phone software etc)
Page 19 Zone Control diagram
Page 15 Home setup
Page 12 Pairing your gateway to your wireless internet
Page 8 Downloading the EMBER App
Page 7 Pairing your thermostats to your programmer
Page 6 Pairing your programmer to your gateway
Page 5 LCD / LED / Button legend
4
WiFi Requirement
The SSID of your Wi-Fi should not
be hidden when you are pairing the
gateway to your router.
Please install the gateway in a place
with a good Wi-Fi signal.
The gateway can only support 2.4GHz
wireless routers. It does not support
5GHz wireless routers.
The MAC address of gateway should
not be in the blacklist of the router.
Please restart your wireless router
periodically or restart it before you
are going on holiday to ensure that
the connection is kept after long
periods of inactivity.
Pay attention to the number of
devices connected to your wireless
router. Some routers may not work
properly if too many devices are
connected.
Device Operating System
1) Minimum iOS is 9.
2) Minimum Android OS is 5.1
(Lollipop)
Positioning of the gateway
The gateway should be located near
the programmer in an area with
good WiFi signal. It should not be
installed close to appliances such as
microwaves, televisions etc.
The above will ensure a stable
connection for remotely controlling
your heating system.
1 Getting Started
Useful Information:
Visit EMBER YouTube channel for the PS
Set up Guide.
On the Initial Setup screen, click on the
Setting icon to access Tutorials, FAQs
and Videos.
5
LCD / LED / Button Legend
WPS / Smartlink
button
Function button
Figure (5-a): The gateway
Figure (5-b): The RF programmer
Buttons to be used during gateway installation
LED Status
Red LED on Gateway not connected to WiFi
Green LED on Gateway connected to WiFi
Red & Green LEDs On WiFi connection issue. Reset router.
6
1. Reset your router by switching it
off and on.
2. On the Programmer, press
button for 5 seconds.
3. ‘Wireless Connect’ will appear on
the screen. Figure (6-a)
4. Press the button for 3 seconds.
You will now enter the gateway
connection screen.
5. A four digit code will alternate on
the screen. Figure (6-b)
6. On the Gateway, press and hold
the ‘Function’ button for 10
seconds.
7. Red and green LEDs on
the gateway will both ash
simultaneously every 1 second.
8. On the Programmer – R1 appears
on the screen. * Figure (6-c)
9. Wait for the LEDs on the gateway
to stop ashing.
10. Press the button.
* If R2, R3 or R4 appears on the screen and you are not setting up a multi programmer
system, please reset the RF connections to the gateway by completing the following:
Press and hold the crystal button until it begins to ash.
Press the Smartlink / WPS button once.
The LEDs will stop ashing for 5 seconds.
Once the LEDs begin to ash again, press the crystal button 3 times.
This will reset all RF connections to the gateway.
You can now complete steps 2 – 9 above.
Pairing your programmer
to your gateway
Figure (6-a): ‘Wireless Connection’ screen
Figure (6-b): ‘Gateway Connection’ screen
Figure (6-c): ‘Gateway Connection’ screen
Complete this step before pairing your thermostats to your programmer
7
1. Lower the cover on the front of the
RF programmer. Move the selector
switch to the ‘RUN’ position.
2. On the RF programmer, press the
button for 5 seconds. Wireless
Connect will appear on the screen.
Figure (7-a)
3. On the RFR wireless room
thermostat or RFC wireless
cylinder thermostat, press the
‘Code’ button. This is located inside
the housing on the Printed Circuit
Board. Figure (7-b)
4. On the RF programmer, the
available zones will begin to ash.
5. Press the
ZONE SELECT
button for
the zone you wish to connect the
thermostat to.
6. The wireless symbol appears on
the screen.
7. The thermostat will count to 3
and then display the zone of the
programmer that it is paired to. If
it is paired to the rst zone it will
display r1, the second zone r2 etc.
Figure (7-c)
Press the wheel on the thermostat
to complete the pairing process.
8. The RF programmer is now
operating in the wireless mode.
The temperature of the wireless
thermostat is now displayed on the
programmer.
9. Repeat this process for the second,
third and fourth zone if required.
Pairing your thermostats
to your programmer
Figure (7-a) ‘Wireless Connection’ screen
Figure (7-b) Printed Circuit Board
Figure (7-c) Zone screen
Reset button Code button
RUN
CLOCK
SET
PROG
SET
Complete this step after pairing your programmer to your gateway
8
2. Once the app has been installed,
open it.
3. Select ‘Create an account’ to Sign
up with your email address.
1. Go to the Apple App Store on
your iPhone or the Google Play
Store on your Android device and
download the EPH Ember App.
QR codes to the download links
are available on the back cover.
Downloading the
EMBER App
9
9. Enter your telephone number.
(optional)
10. Tick the box to accept our Terms
& Conditions and Privacy Policy.
11. Press ‘Sign up’.
4. Enter your First name.
5. Enter your Last name.
6. Enter your Email address.
7. Enter your Password (Minimum 6
characters – including lowercase,
uppercase and number)
8. Conrm your Password.
10
14. You will be directed to the EMBER
App. Select ‘Open’ in EMBER. If
you are not automatically directed
to the App, manually open it and
complete step 15.
12. A conrmation email should
arrive in your inbox from EMBER.
This should take up to 2 minutes.
If you do not receive the email,
please search your Junk / Spam
email folder.
13. Open the email and press the
embedded button ‘Activate
Account’.
Downloading the
EMBER App (Continued)
Indice
Altri manuali Ember Portale
Manuali Portale popolari di altre marche
LST
LST M500RFE-AS Manuale utente
Kinnex
Kinnex Media Gateway Manuale utente
2N Telekomunikace
2N Telekomunikace 2N StarGate Manuale utente
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuale utente
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Manuale utente
Telsey
Telsey CPVA 500 - SIP Manuale utente
