Ember GW03 Manuale utente
GATEWAY INSTRUCTIONS
GW03
Dual Band 2.4/5GHz
2
Welcome
Thank you for choosing EMBER Smart Heating by EPH Controls.
We hope you enjoy using it as much as we did developing it!
Controlling your heating anywhere, anytime is only a few simple
steps away.
In this booklet, we will provide a step by step guide to setting
up the EMBER Smart Heating Control app and its associated
hardware.
Again, thank you for choosing EMBER.
3
Index
Page 4 Getting started (WiFi requirements / Device software etc)
Page 21 Zone control diagram
Page 12 Initial Setup
Page 14 Pairing your GW03 gateway to your 2.4/5GHz WiFi (Android)
Page 16 Pairing your GW03 gateway to your 2.4/5GHz WiFi (iOS)
Page 18 Home setup
Page 8 Downloading the EMBER App
Page 7 System architecture
Page 6 Pairing your receiver to your gateway
Page 6 Making your RF1A-OT receiver a hub receiver
Page 5 LCD / LED / Button legend
4
WiFi Requirement
The SSID of your Wi-Fi should not
be hidden when you are pairing the
gateway to your router.
The gateway can only support 2.4GHz
and 5GHz wireless routers. Please
refer to the gateway pairing section
beginning on page 12.
The gateway should not be in the
blacklist of the router.
Please restart your wireless router
periodically or restart it before you
are going on holiday to ensure that
the connection is kept after long
periods of inactivity or a power cut.
Pay attention to the number of
devices connected to your wireless
router. Some routers may not work
properly if too many devices are
connected.
For BT routers the wireless mode
should be set to Mode 3 in the router
settings.
Device Operating System
1) Apple iOS 9 or later.
2) Android OS 5.1 Lollipop or later.
Positioning of the gateway
The gateway should be located near
the receiver in an area with good WiFi
signal.
It is important to keep the gateway
at least 1 metre away from other
electronics. Appliances such as
microwaves, T.V’s, WiFi Routers and
Boosters, Smart Speakers, Wireless
Alarm systems etc. These can
interfere with the gateway signal.
Choosing a good location will ensure
a stable connection for remotely
controlling your heating system.
Getting started
Useful Information:
Visit EMBER YouTube
channel for the TS Set
up Guide.
On the Initial Setup screen, click on the
Setting icon to access Tutorials, FAQs
and Videos.
5
LCD / LED / Button legend
WiFi Connection
button
Function
button
Reset
button
Figure 1: The gateway
Figure 2: The RF receiver
Buttons to be used during gateway installation
Reset
WiFi ConnectFunction
Power
SupplyReset
LED Status
Red LED on Gateway has power
Green LED on Gateway connected to WiFi
White LED on Gateway connected to receiver
Allow 300mm clearance
for receiver reset button
6
** Please note: If you are installing a CP4i, the thermostat, receiver and gateway will
have pre-established RF connections so there is no need to carry out the steps in this
section.
1. Ensure that your thermostat(s)
are paired to your receiver(s).
This can be tested by turning the
thermostat temperature up or
down and ensuring the receiver is
switching on and off accordingly.
If a thermostat is not paired to
the receiver please follow the
instructions in section 17 of
RFRP-OT Operating Instructions.
2. Ensure that the receiver you’re
connecting to the boiler is set up
as a hub receiver. For instructions
on how to do this, please see
steps below.
Making your RF1A-OT receiver into a Hub Receiver.
1. Press the Reset button on the receiver that you wish to make the Hub
Receiver - Red and Green lights will both be solid on.
2. Immediately press and hold Connect and simultaneously for 5 seconds,
until the Red light starts blinking.
3. Press
Connect
once and the Green light will be solid - this is now the hub
receiver.
4. Press fto exit to the normal interface.
Note: If you are connecting multiple receivers to a gateway, please ensure that all branch
receivers are connected to the hub receiver. There can only be 1 hub receiver in a system.
Allow 5 minutes for all receivers to synchronise with the hub receiver before connecting
the gateway to the EMBER App. See page 44 / 45 of the CP4 instructions.
* Please note: If you are installing a CP4 or CP4-HW-OT, the thermostat and the receiver
will have a pre-established RF connection so it is not necessary to carry out Step 1 in
the RF connection process below.
Pairing your receiver to
your gateway
Complete this step below to pair your receiver to your GW03 Gateway
To optimise battery life, the end to end communication can take up to 3 minutes .
3. Press the
Connect
button on the
receiver. The Red and Green LEDs
will begin to ash simultaneously.
If only the Red light ashes,
please see the steps below to
make your receiver into a hub
receiver.
4. On the Gateway, press and hold
the ‘Function’ button for 3 sec.
5. The White LED on the gateway
will begin to ash at 1 second
intervals.
6. When the White LED becomes
solid On, the gateway has been
connected to the hub receiver.
7
RFRP-HW-OT Thermostat
RF1A-OT Branch Receiver
RFRP-OT Thermostat
RF1A-OT Hub Receiver
RFRP-OT Thermostat
RF1A-OT Branch Receiver
RFRP-OT Thermostat RF1A-OT Receiver GW03 Gateway EMBER App Cloud
Cloud
EMBER App
GW03 Gateway
Note: A maximum of 6 CP4 can be used with each GW03 gateway.
System architecture
To optimise battery life, the end to end communication can take up to 3 minutes .
Example A Single Zone System
Example B Multi Zone System
8
2. Once the App has been installed,
open it.
3. Select ‘Create an account’ to Sign
up with your email address.
1. Go to the Apple App Store on
your iPhone or the Google Play
Store on your Android device
and download the EMBER Smart
Heating Control App.
QR codes to the download links
are available on the back cover.
Downloading the
EMBER Smart Heating Control App
9
4. Enter your email address.
5. Conrm your email address.
6. Accept the Terms & Conditions.
7. A conrmation email will arrive in
your inbox from EMBER.
This can take up to 2 minutes.
If you do not receive the email,
please search your Junk / Spam
email folder.
8. Open the email and you will
retrieve your 6 digit code.
Note: If you are using a company
email address the registration may be
blocked by your company email policy.
Refer to your company IT.
10
Downloading the
EMBER Smart Heating Control App
(Continued)
9. Return to the EMBER App and
enter your 6 digit code.
10. Enter your First name.
11. Enter your Last name.
12. Enter your Password. (Minimum 6
characters - including lowercase,
uppercase and number).
13. Conrm your Password.
14. Enter your Phone Number.
(Optional)
Altri manuali per GW03
1
Indice
Altri manuali Ember Portale
Manuali Portale popolari di altre marche
LST
LST M500RFE-AS Manuale utente
Kinnex
Kinnex Media Gateway Manuale utente
2N Telekomunikace
2N Telekomunikace 2N StarGate Manuale utente
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuale utente
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Manuale utente
Telsey
Telsey CPVA 500 - SIP Manuale utente
