Ember GW03 Manuale utente
GATEWAYINSTRUCTIONS
GW03
2
Welcome
Thank you for choosing EMBER Smart Heating by EPH Controls.
We hope you enjoy using it as much as we did developing it!
Controlling your heating anywhere, anytime is only a few simple
steps away.
In this booklet, we will provide a step by step guide to setting
up the EMBER Smart Heating Control app and its associated
hardware.
Again, thank you for choosing EMBER.
3
Index
Page 4 Getting started (WiFi requirements / Device software etc)
Page 23 Zone control diagram
Page 20 Home setup
Page 12 Pairing your GW03 gateway to your wireless internet
Page 14 Pairing your GW03 gateway to your 2.4GHz WiFi
Page 16 Pairing your GW03 gateway to your 5GHz WiFi (Android)
Page 18 Pairing your GW03 gateway to your 5GHz WiFi (iOS)
Page 8 Downloading the EMBER App
Page 7 System architecture
Page 6 Pairing your receiver to your GW03 gateway
Page 6 Making your RF1A-OT receiver a hub receiver
Page 5 LCD / LED / Button legend
4
WiFi Requirement
The SSID of your Wi-Fi should not
be hidden when you are pairing the
gateway to your router.
The gateway can only support 2.4GHz
and 5GHz wireless routers. Please
refer to the gateway pairing section
beginning on page 12.
The gateway should not be in the
blacklist of the router.
Please restart your wireless router
periodically or restart it before you
are going on holiday to ensure that
the connection is kept after long
periods of inactivity or a power cut.
Pay attention to the number of
devices connected to your wireless
router. Some routers may not work
properly if too many devices are
connected.
During the connection process you
will need to specify which band your
WiFi is broadcasting on. (2.4GHz or
5GHz.) If you are not sure, you may
need to go to your router settings to
check. Alternatively you can contact
your internet provider.
Device Operating System
1) Apple iOS 9 or later.
2) Android OS 5.1 Lollipop or later.
Positioning of the gateway
The gateway should be located near
the receiver in an area with good WiFi
signal. It should not be installed close
to appliances such as microwaves,
televisions, internet boosters and
smart speakers etc.
Choosing a good location will ensure
a stable connection for remotely
controlling your heating system.
Getting started
Useful Information:
Visit EMBER YouTube
channel for the TS Set
up Guide.
On the Initial Setup screen, click on the
Setting icon to access Tutorials, FAQs
and Videos.
5
LCD / LED / Button legend
WPS / Smartlink
button
Function
button
Reset
button
Figure 1: The gateway
Figure 2: The RF receiver
Buttons to be used during gateway installation
Reset
WPS / SmartlinkFunction
Power
SupplyReset
LED Status
Red LED on Gateway has power
Green LED on Gateway connected to WiFi
White LED on Gateway connected to receiver
6
1. Ensure that your thermostat(s)
are paired to your receiver(s).
This can be tested by turning the
thermostat on or off and ensuring
the receiver is switching on and
off accordingly. If a thermostat
is not paired to the receiver
please follow the instructions in
section 17 of RFRP-OT Operating
Instructions.
2. Ensure that the receiver you’re
connecting to the boiler is set up
as a hub receiver. For instructions
on how to do this, please see
steps below.
Making your RF1A-OT receiver into a Hub Receiver.
1. Press the Reset button on the receiver that you wish to make the Hub
Receiver - Red and Green lights will both be solid.
2. Immediately press and hold
Connect
and for 5 seconds, the Red light will
start blinking.
3. Press
Connect
and the Green light will be solid - this is now the hub receiver.
4. Press fto exit to the normal interface.
Note: If you are connecting multiple receivers to a gateway, please ensure that all branch
receivers are connected to the hub receiver. There can only be 1 hub receiver in a system.
Allow 5 minutes for all receivers to synchronise with the hub receiver before connecting
the gateway to the EMBER App.
* Please note: If you are installing a CP4 or CP4-HW-OT the thermostat and the receiver
will have a pre-established RF connection so it is not necessary to carry out Step 2 in
the RF connection process below.
** Please note: If you are installing a CP4i, the thermostat, receiver and gateway will
have pre-established RF connections so there is no need to carry out the steps in this
section.
Pairing your receiver to
your gateway
Complete this step below to pair your receiver to your GW03 Gateway
3. Press the ‘Connect’ button on the
receiver. The Red and Green LEDs
will begin to flash simultaneously.
If only the Red light flashes,
please see the steps below to
make your receiver into a hub
receiver.
4. On the Gateway, press and hold
the ‘Function’ button for 3 sec.
5. The White LED on the gateway
will begin to flash at 1 second
intervals.
6. When the White LED become
solid On, the gateway has been
connected to the hub receiver.
7
RFRP-HW-OT Thermostat
RF1A-OT Branch Receiver
RFRP-OT Thermostat
RF1A-OT Hub Receiver
RFRP-OT Thermostat
RF1A-OT Branch Receiver
RFRP-OT Thermostat RF1A-OT Receiver GW03 Gateway EMBER App Cloud
Cloud
EMBER App
GW03 Gateway
Note: A maximum of 6 thermostats can be used with each GW03 gateway.
System architecture
To optimise battery life, the end to end communication can take up to 3 minutes .
Example A Single Zone System
Example B Multi Zone System
8
2. Once the app has been installed,
open it.
3. Select ‘Create an account’ to Sign
up with your email address.
1. Go to the Apple App Store on
your iPhone or the Google Play
Store on your Android device
and download the EMBER Smart
Heating Control App.
QR codes to the download links
are available on the back cover.
Downloading the
EMBER Smart Heating Control App
9
9. Enter your telephone number.
(optional)
10. Tick the box to accept our Terms
& Conditions and Privacy Policy.
11. Press ‘Sign up’.
4. Enter your First name.
5. Enter your Last name.
6. Enter your Email address.
7. Enter your Password (Minimum 6
characters – including lowercase,
uppercase and number)
8. Confirm your Password.
10
14. You will be directed to the EMBER
App. Select ‘Open’ in EMBER. If
you are not automatically directed
to the App, manually open it and
complete step 15.
12. A confirmation email will arrive in
your inbox from EMBER.
This can take up to 2 minutes.
If you do not receive the email,
please search your Junk / Spam
email folder.
13. Open the email and press the
‘Activate Account’ button.
Downloading the
EMBER Smart Heating Control App
(Continued)
Altri manuali per GW03
1
Indice
Altri manuali Ember Portale
Manuali Portale popolari di altre marche
LST
LST M500RFE-AS Manuale utente
Kinnex
Kinnex Media Gateway Manuale utente
2N Telekomunikace
2N Telekomunikace 2N StarGate Manuale utente
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuale utente
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Manuale utente
Telsey
Telsey CPVA 500 - SIP Manuale utente
