Emerson Fisher FIELDVUE DVC5000 Guida alla configurazione

www.Fisher.com

HARTrField Device Specification

Fisher™FIELDVUE™DVC5000 Digital Valve

Controllers

HART Revision Device Type Device Revision Firmware Revision

HART 5 02 23, 4

35, 6

Introduction 2.................................

Product Overview 2............................

Purpose of this document 2.....................

Abbreviations and definitions 2..................

Reference Documentation 3....................

Device Identification 3..........................

Product Interfaces 4............................

Control Valve Interface 4.......................

Host interface 4...............................

Internal Jumpers And Switches 5.................

Write Protection 5.............................

Firmware Upgrade 5...........................

Dynamic Variables 6............................

Device Variables 6..............................

Status Information 7............................

Device Status 7...............................

Universal Commands 8..........................

CommonPractice Commands 13.................

Supported Commands 13......................

Device-Specific Commands 21....................

Burst Mode 21................................

Catch Device Variable 21.......................

Performance 21................................

Annex A Compatibility Checklist 22................

Annex B DVC5000 Parameters as part

of a Rosemountr1410/1420 WirelessHARTr

Gateway 23...............................

Instruction Manual Supplement

D103266X012

DVC5000 Digital Valve Controller

May 2018

Product removed from sale October 2003

Instruction Manual Supplement

D103266X012

DVC5000 Digital Valve Controller

May 2018

Introduction

Product Overview

The FIELDVUE DVC5000 digital valve controller is designed to control the pneumatic actuator of a process control

valve. It receives a current signal from a host and uses instrument air supply to create a metered pressure output signal

to the pneumatic actuator. Movement of the actuator as it positions the process control valve is measured by the

DVC5000 travel sensor as its primary feedback. The name plate is located on the side of the DVC5000 master module

assembly and indicates the model name, individual product serial number, and any applicable third party approvals.

Purpose of this document

This specification is designed to be a technical reference for HART capable host application developers, system

integrators and knowledgeable end-users. It also provides functional specifications (e.g., commands, enumerations

and performance requirements) used during field device development, maintenance and testing. This document

assumes the reader is familiar with HART Protocol requirements and terminology. Additional product information is

available in the DVC5000 product literature, available from your Emerson sales office or Local Business Partner.

Abbreviations and definitions

AR Alert Record

Configuration

Variables

Variables which represent nonvolatile values of manufacturinginitialized data or userspecified

configuration information. These variables cannot be enumerated via Command 54 and as such

stand on their own with no associated units or range information.

Device Variable

Measured variables that are exposed to HART and can be enumerated using Command 54.

Generally there are variables whose ID is in the range of 0 to 10 and are associated with units

codes, status, and range values.

Enumeration A pre-defined set of values or text.

MV Measured Variable, a physical input to the instrument.

NV Named Variable – a logical point inside the device, hardmapped to a given MV as the source of

NV data.

Point A term that applies to diagnostic data packets. It is defined as a collection of periodically sampled

variables captured at a single instant in time. It does not include the “Monitor” point.

Byte An 8bit unsigned integer.

Word A 16bit unsigned integer.

Float Refers to the IEEE 754 floating point format.

Packed ASCII A special form of characters defined by HART in which 6bit ASCII characters are packed into byte

data.

Standard Span

Format

A proprietary 16bit integer format for numerical values used by some of this device’s Device

Specific commands.

Instruction Manual Supplement

D103266X012

DVC5000 Digital Valve Controller

May 2018

Reference Documentation

HART Smart Communications Protocol Specification Revision 5; a group of documents specifying the HART

Communication Protocol, physical layers, and Data Link Layers as defined by the HART Communications Foundation.

The DVC5000 is not an Active product. Contact your Emerson sales office or Local Business Partner if a copy of the

instruction manual is required.

Device Identification

Manufacturer Name Fisher Controls Model Name(s) DVC5000

Manufacture ID Code 19 (13 Hex) Device Type Code 02 (02 Hex)

HART Protocol Revision 5Device Revision 2 or 3

User Selectable HART Revision

between HART 5 and HART 7 No

Number of Device Variables 9

Physical Layers Supported FSK

Physical Device Category Valve Positioner

Instruction Manual Supplement

D103266X012

DVC5000 Digital Valve Controller

May 2018

Product Interfaces

Control Valve Interface

The DVC5000 digital valve controller is mechanically attached to the valve’s actuator by means of a mounting bracket.

The control valve's position is conveyed to the travel sensor of the DVC5000 digital valve controller by means of the

feedback bracket attached to the actuator’s stem and the rotating travel sensor.

MOUNTING

BRACKET

Pneumatic tubing connected to the DVC5000 brings instrument supply air to the DVC5000 and takes controlled

output air from the DVC5000 to the actuator. The pressure sensor in the DVC5000 measures the output pressure and

presents it as a device variable.

Host interface

The input to the DVC5000 can either be twowire 4to20 mA current loop (in pointtopoint mode) or 24 VDC (in

multidrop mode). This input is connected in the DVC5000’s terminal box on two terminals marked “LOOP +” and

“LOOP ”. Refer to the DVC5000 instruction manual for connection details.

Instruction Manual Supplement

D103266X012

DVC5000 Digital Valve Controller

May 2018

Internal Jumpers And Switches

The input to the DVC5000 is determined by the PtPt/MultiDrop switch on the printed wiring board.

MULTI‐DROP SWITCH

AUXILIARY

SWITCH

(MULTI‐DROP)

DOWN

(POINT-TO-POINT)

A6191‐1

LOOP-

LOOP+

Refer to the DVC5000 instruction manual for additional details on the settings of the selection switches.

Write Protection

There are two Write Protection states for the DVC5000: Not Protected or Protected. Protected prevents configuration

and calibration changes to the instrument. The default setting is Not Protected. Protection is controlled under

software control. Write Protection can be enabled remotely. However, to disable Write Protection to Not Protected,

you must have physical access to the instrument. The procedure will require you to short the AUX terminals inside the

terminal box when directed by the software as a security measure.

Firmware Upgrade

The firmware of a DVC5000 printed wiring board assembly cannot be upgraded.

Instruction Manual Supplement

D103266X012

DVC5000 Digital Valve Controller

May 2018

Dynamic Variables

Four Dynamic Variables are implemented.

COMMAND/RESPONSE MODE BURST MODE

Default Meaning Units Default Meaning Units

PV Analog Input mA, % Valve Travel %

SV Aux Contact Status %Travel Setpoint %

TV Pressure PSI, BAR, KPA Pressure PSI, BAR, KPA

FV Valve Travel %FW5: Aux Status %

FW6: Drive Signal %

Device Variables

These variables represent measurements taken by the device, are read only values, and are all in float format. These

can be read with Commands 33 and 54.

Variable ID Meaning Units

0Analog Input mA, %

1Auxiliary Contact Status (0% = Open, 100% = Shorted) %

2Output Pressure PSI, BAR, KPA

3Valve Travel %

4Drive Signal %

5 Unused

6Travel Setpoint %

7 Unused

8 Unused

9Implied Valve Position (Travel Target) %

10 Valve Travel %

211 Temperature _C, _F

Unit Codes

Variable Units Code Units

0No Units

6Pounds per square inch, psi

7 Bar

12 ($0C) Kilopascals, kPa

32 ($20) Celsius, _C

33 ($21) Fahrenheit, _F

39 ($27) Milliamps, mA

57 ($39) Percent, %

Instruction Manual Supplement

D103266X012

DVC5000 Digital Valve Controller

May 2018

Status Information

Device Status

The Field Device Status Byte is the only status byte defined in the HART protocol. The order and meaning of each of the

eight bits within the byte are fixed by the protocol. This byte is one of the status bytes included with each HART

response. It is not part of the Command 48 data.

Bit Device Revision Name of Status Bit Meaning

72, 3 Field Device Malfunction

Set / cleared by the firmware based on self test results.

This bit is set if the pressure, position or temperature

sensors provide invalid readings.

62, 3 Configuration Changed

Two such bits exist internally, one for each HART master.

Both copies are set when any variable, HART message,

tag, descriptor or date are changed from HART. Cleared

by command 38, separately for each master. This bit

survives loss of power.

52, 3 Cold Start

Set by the firmware whenever a RESET sequence is

executed or at initial device power up. Cleared by the

first HART command.

42, 3 More Status Active when any bit in command 48 is active.

2Not Used

3Analog Input Fixed

Active if the Instrument Mode of the DVC5000 is in the

“Out Of Service” condition or if the Control Mode of the

DVC5000 is in one of the digital set point modes.

22Analog Input Saturated

Active if the Instrument Mode of the DVC5000 is in the

“Out Of Service” condition or if the Control Mode of the

DVC5000 is in one of the digital set point modes.

3Not Used

12, 3 Internal Sensor Out of Limits

(This bit is named “NonPrimary Variable Out Of Limits”

in the HART documentation for transmitters. It has been

renamed to reflect the fact that these variables are

INTERNAL INPUTS to FIELDVUE products). The firmware

sets this bit when any sensor (pressure, position,

temperature) exceeds its operating limits.

02, 3 Loop Current Out of Range Set when any variable 0 (Analog Input) is saturated.

Instruction Manual Supplement

D103266X012

DVC5000 Digital Valve Controller

May 2018

Universal Commands

The DVC5000 field device implements all HART Revision 5 Universal Commands.

Command 0: Read Unique Identifier

Command 1: Read Primary Variable

Command 2: Read Loop Current and Percent of Range

Command 3: Read Dynamic Variables and P.V. Current

Command 6: Write Polling Address

Command 11: Read Unique Identifier Associated with Tag

Command 12: Read Message

Command 13: Read Tag, Descriptor, Date

Command 14: Read Primary Variable Transducer Information

Command 15: Read Primary Variable Output Information

Command 16: Read Final Assembly Number

Command 17: Write Message

Command 18: Write Tag, Descriptor, Date

Command 19: Write Final Assembly Number

Instruction Manual Supplement

D103266X012

DVC5000 Digital Valve Controller

May 2018

Command 0: Read Unique Identifiers

Byte Description Format Value

Request

Data Bytes none

Response

Data Bytes

0Data type expansion code Byte, hex $FE

1Manufacturer identification code Byte, hex $13

2Manufacturer’s Device Type code Byte, hex $02

3Number of preambles Byte, hex $05

4Universal command revision Byte, hex $05

5Device revision Byte, hex See table 1 below

6Software revision Byte, unsigned integer See table 1 below

7Hardware revision Byte, unsigned integer See table 2 below

8Device function flags Not Used $00

9Device Identification number 3 Bytes, hex

Code Description

Command

Specific

Response

Codes

none

Table 1. Device and Software Revision

Device Revision Software Revision Description

$02 $03 Firmware Revision 3

$04 Firmware Revision 4

$03 $05 Firmware Revision 5

$06 Firmware Revision 6

Table 2. Hardware Revision

Hardware Revision Description

($08) Not applicable

($10) Hardware revision 2

($18) Hardware revision 3

($20) Hardware revision 4

($28) Hardware revision 5

Instruction Manual Supplement

D103266X012

DVC5000 Digital Valve Controller

May 2018

Command 1: Read Primary Variable

This command reads the value of the DVC5000’s measured Valve Travel. The units are “%”.

Byte Format Description

Request

Data Bytes none

Response

Data B

tes

0Byte, hex Valve Travel Unit Code, 57(%)

14 Float Valve Travel value

Code Class Description

Command

Specific

Response

Codes

none

Command 2: Read Loop Current and Percent of Range

This command reads the value of the DVC5000’s loop current in implied units of “mA” (regardless of the configured

units setting) and the measured Valve Travel in units of “%”.

Byte Format Description

Request

Data Bytes none

Response

Data B

tes

03 Float Loop Current

47 Float Valve Travel

Code Class Description

Command

Specific

Response

Codes

none

Indice

Altri manuali Emerson Controllori

Emerson

Emerson Fisher Accu-Pressure Y693 Manuale utente

Emerson

Emerson Fisher EZH Series Manuale utente

Emerson

Emerson Fisher 657C Manuale utente

Emerson

Emerson Tescom 44-3400 Series Manuale utente

Emerson

Emerson FISHER T208 Series Manuale utente

Emerson

Emerson Site Supervisor Manuale utente

Emerson

Emerson Copeland EV2 Series Guida utente

Emerson

Emerson FISHER 6492L Manuale utente

Emerson

Emerson Keystone EPI2 Manuale utente

Emerson

Emerson Fisher SR5 Manuale utente

Emerson

Emerson TESCOM 04 Series Guida all'installazione

Emerson

Emerson Bettis RP4AF Manuale utente

Emerson

Emerson Bettis G2XXX M11 series Istruzioni operative

Emerson

Emerson Fisher FIELDVUE DVC6005 Series Guida alla configurazione

Emerson

Emerson FL Manuale utente

Emerson

Emerson Fisher EZL Manuale utente

Emerson

Emerson Fisher 1051 Manuale utente

Emerson

Emerson EIM HQ Series Manuale utente

Emerson

Emerson Dixell XRi30T Schema elettrico

Emerson

Emerson Vilter MicroVission Manuale operativo

Emerson

Emerson Fisher MR95 Series Manuale utente

Emerson

Emerson Bettis CBB Series Istruzioni per l'installazione

Emerson

Emerson EZH Manuale utente

Emerson

Emerson dixell XR02CX Schema elettrico

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente

3M MicroTouch EX113 Manuale utente