Endon EL-40053 Manuale utente

The Light pack contains:

Wall light and bracket.

Terminal connection block.

LED GU10 lamp

The following tools may be required:

Selection of cross and flat head screwdrivers.

Electric drill and assorted drill bits.

Wire strippers.

Electrical insulation tape.

INSTRUCTION MANUAL

This product is only suitable for connection to a 240V~50Hz supply.

It is recommended that this light is installed by a qualified electrician in accordance with current IEE Wiring

Regulations and Building Regulations (Part P).

The light fitting should be connected to a lighting circuit protected by a 5 amp fuse (or a 6 amp miniature

circuit breaker).

This light has an IP44 (splash proof) rating suitable for use outdoors.

Run supply wire from a 5-amp electrical supply using double insulated 3-core cable of type H05RN-F 1.0mm2

(not supplied) to selected site, ensuring it is adequately protected through the full length of the cable run, it

must come out of the flat surface of the mounting surface in line with the entry to the fitting.

Except where installed in a conduit or duct , which provides equivalent protection against mechanical damage,

a cable buried in the ground shall incorporate an earthed armour or metal sheath or both, suitable for use as a

protective conductor, or be of insulated concentric construction. Buried cables shall be marked by cable

covers or a suitable marking tape. Buried conduits and ducts shall be suitably identified. Buried cables,

conduits and ducts shall be at a sufficient depth to avoid being damaged by any reasonably foreseeable

disturbance of the ground.

This product contains breakable parts – be careful during handling and maintenance to avoid breakage.

The shade can become hot in use. Switch off and allow 10 minutes to cool before cleaning (using a dry cloth

only – do not use liquid or abrasive cleaners).

If the cover is broken or cracked then it must be replaced immediately to preserve the water ingress

protection, please consult your retailer. This is represented by the symbol

This is fitted with an LED lamp and we recommend that you do not stare into the light beam of LED`s.

If any modification is made it will invalidate the warranty and may render the product unsafe.

Before you start

Please read these instructions carefully before fitting your new light and retain for reference.

Switch off the mains supply and remove the appropriate fuse or switch off the appropriate circuit breaker

before commencing installation.

Ensure that no one else has access that would enable the supply to be inadvertently reconnected.

Check the packaging and make sure that you have all the required parts.

Follow each assembly step in order to prevent incorrect assembly

Make sure all screws / nuts, including electrical connections etc are fully tightened before use.

EL- 40053 Outdoor wall fitting.

Safety Warnings

Endon

LS9 0SE

20150324

These assembly diagrams are intended as a guide – if in doubt consult a qualified electrician.

Assembly / user instructions

P570 07

Diagram A

Diagram B

Diagram C

1. Diagram A. Determine the position of your light fitting

taking into account the exit position of the cable.

Ensure that the mounting surface is solid, preferably a

brick or block wall and ensure that there are no other

cables or pipes beneath the surface. Use appropriate

fixings. Wall plugs and screws as supplied are shown

here.

2. Separate the plastic back plate from the fitting by

removing the two domed nuts on the front of the fitting.

Leave the threaded (1) bolts in the back plate. Use the

back plate as a template to mark the screw holes.

Make sure the back plate is correctly aligned.

3. Diagram B. Use a sharp object such as a screwdriver

to pierce the rubber grommet in the back plate. Feed

the incoming cable (2) through the rubber grommet and

attach the back plate to the wall. Do not over tighten as

this could damage the back plate.

4. Diagram C. Connect the house wiring to the internal

terminal block. The terminal block can be removed

from its mount for ease of connection. NOTE: This is a

Class II fitting and must not be earthed. If you have

any earth cables make sure that they are connected to

each other – to maintain earth continuity throughout

your property – and wrap them in insulation tape and

keep them away from the terminal connections of the

fitting.

5. Diagram D. Place the fitting over the back plate,

ensuring that the bolts in the back plate are aligned

with the holes in the front of the fitting. Replace the

domed nuts (3) to secure the fitting. Do not over

tighten. Fit the LED bulb (supplied) into the lamp

holder.NOTE: Never fit bulbs of a higher wattage

or of a type other than those specified on the label

(as these may cause overheating and damage the

fitting).

6. Diagram E. Fit the bulb cover

7. Turn on the power and test.

Diagram D

Diagram E

(1)

(2)

(3)

Internal

cables

Indice

Altri manuali Endon Luce esterna

Endon

Endon EL-40098 Manuale utente

Endon

Endon EL-533-28W-T5 Manuale utente

Endon

Endon Roko Manuale utente

Endon

Endon Burford Manuale utente

Endon

Endon 77120 Manuale utente

Endon

Endon YG-8000 Manuale utente

Endon

Endon Burford Manuale utente

Endon

Endon Pagoda PIR Outdoor Wall Light Manuale utente

Endon

Endon EL-40085 Manuale utente

Endon

Endon YG-861-SS Manuale utente

Endon

Endon YG-4002-SS Manuale utente

Endon

Endon Canillo Manuale utente

Endon

Endon EL-40094 Manuale utente

Endon

Endon Leyton Manuale utente

Endon

Endon EL-40022 Manuale utente

Endon

Endon EL-YG -5006 Manuale utente

Endon

Endon YG-3004 Manuale utente

Endon

Endon Joshua Manuale utente

Endon

Endon EL- 40101 Manuale utente

Endon

Endon EL- 40094 Manuale utente

Endon

Endon YG- 8002 Manuale utente

Endon

Endon EL-10049 Manuale utente

Endon

Endon Breton Outdoor Wall light Fitting Manuale utente

Endon

Endon YG-864-SS Manuale utente

Manuali Luce esterna popolari di altre marche

Sealey

Sealey LED37 Manuale utente

nordlux

nordlux VEJERS Guida utente

SImx

SImx ELITE LED LHTC637 Manuale utente

GEV

GEV CAROLINE 10833 Manuale utente

NEBO

NEBO NEB-LSP-0020 Manuale utente

WE-EF

WE-EF PFL540 LED Manuale utente

Lindby

Lindby 9949029 Manuale utente

HEPER

HEPER DOGO Side LW6048.585-US Istruzioni per l'installazione e il funzionamento

HEPER

HEPER LW8034.003-US Istruzioni per l'installazione e il funzionamento

Maretti

Maretti VIBE S 14.6080.04.A Manuale utente

BEGA

BEGA 84 253 Manuale

HEPER

HEPER MINIMO Istruzioni per l'installazione e il funzionamento

LIGMAN

LIGMAN BAMBOO 3 Manuale utente

Maretti

Maretti TUBE CUBE WALL 14.4998.04 Manuale utente

Maxim Lighting

Maxim Lighting Carriage House VX 40428WGOB Manuale utente

urban ambiance

urban ambiance UQL1273 Manuale utente

TotalPond

TotalPond 52238 Manuale utente

Donner & Blitzen

Donner & Blitzen 0-02661479-2 Manuale utente