Endress E-RMA LAN Manuale operativo

Translation of the original operating

manual

E-RMA LAN

Article-No.: 342 221

Manufacturer ENDRESS Elektrogerätebau GmbH

Neckartenzlinger Str. 39

D-72658 Bempflingen, Germany

Tel: + 49 (0) 71 23 / 9737 - 0

Fax: + 49 (0) 71 23 / 9737 – 50

Email: info@endress-stromerzeuger.de

www: http://www.endress-stromerzeuger.de

Document number /

version

EE134895 / i02

Publication date August 2019

This documentation and parts thereof are subject to copyright. Any use or modi-

fication beyond the restrictions of the Copyright Act is forbidden and subject to

penalty without the consent of ENDRESS Elektrogerätebau GmbH.

This applies in particular to copies, translations, microfilming, as well as storage

and processing in electronic systems.

Notes on printing All descriptions, technical details and illustrations refer to the version of the gen-

erator for printing.

We reserve the right to make modifications in terms of ongoing technical devel-

opment. This operating manual does not include technical modifications that oc-

curred after printing.

The colours in this operating manual do not always comply completely with the

actual designs due to technical printing reasons.

Table of Contents

1 About this manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

2 Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

2.1 Installing an E-RMA LAN module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

2.2 E- RMA LAN connection options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

2.2.1 Activating “Engineer” mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

2.2.2 Direct connection between the PC and the E-RMA LAN. . . . . . . . . . . . . . . . . . . . . .7

2.2.3 Connection from the E-RMA LAN via the internet using a dynamic IP . . . . . . . . . . .8

2.2.4 Connection from the E-RMA LAN via the internet using a static IP. . . . . . . . . . . . . .9

3 AirGate Diag - Diagnostics codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

4 Web supervisor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

4.1 Activating for the web supervisor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

4.2 First steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

About this manual

1 About this manual

We would like to explain to you the safe and proper use of the optional additional

equipment and accessories through this supplementary operating manual. To do

this we have oriented ourselves to the new European standard DIN EN 82079-1

for preparing the user manuals.

For safe and intended use, it is absolutely essential that you read through and

understand these supplementary operating manual carefully before you use an

additional function for the first time.

Your adherence to it will create the foundations for:

• avoiding dangers for yourself and others,

• reducing repair costs and downtimes as well as

• increasing the reliability and service life of the generator.

Apart from this manual, the laws, regulations, guidelines, and standards applica-

ble in the country of use must also be adhered to.

NOTICE!

This document only describes safe operation of the optional additional

equipment and the accessories. It only applies in conjunction with the orig-

inal operating instructions for your basic unit (e.g. floodlighting system),

hereinafter it is always referred to as the operating manual.

► Unless described otherwise in the following, all of the intended use instruc-

tions apply in accordance with the operating manual for the complete device.

► The same applies to all references to foreseeable misuse according to the

operating manual.

Commissioning

2 Commissioning

2.1 Installing an E-RMA LAN module

You will need a LAN cable and an internet-compatible computer or router

to be able to use the E-RMA LAN module. They are needed so that you can

connect up your generator to the internet.

NOTICE!

Check that the power supply going to the control module and the controller

has been disconnected before you insert the E-RMA LAN module.

► Only connect up the E-RMA LAN module after the supply voltage has been

disconnected in order to prevent the E-RMA LAN and control modules from

being damaged.

Conditions Unpacked E-RMA LAN module

LAN cable of a suitable length that goes to the computer / router

Installing an E-RMA

LAN module

1. Open the control panel on your generator by unscrewing the securing

screws.

This means that you have to go to the back of the control module as this

where the E-RMA LAN module attachment is located.

2. Disconnect the power supply going to the control module.

3. CAREFULLY insert the E-RMA LAN module into the control module as

shown in the Fig. 2-1 Installing an E-RMA LAN module illustration.

4. Reconnect the control module's supply voltage.

The control module supplies the power to the E-RMA LAN module.

5. Now connect the LAN cable to the E-RMA LAN module.

6. Secure the control panel back on the generator. Ensure that you do not dam-

age or trap the LAN cable when you do this.

The E-RMA LAN module has been successfully installed.

Fig. 2-1 Installing an E-RMA LAN module

Commissioning

2.2 E- RMA LAN connection options

You will have several options for establishing a connection to your gener-

ator after you have installed the E-RMA LAN module in your generator. You

will find a summary of these options and the settings that you will have to

make for them in the following chapters.

2.2.1 Activating “Engineer” mode

You must first activate "Engineer" mode on your control module before

you can enter the software settings. You will find instructions on how you

can activate this mode below.

1. Start your power generator’s control mod-

ule

2. Hold the Enter button down and then

press the “Page” button four times .

3. This will open the user interface. Use the

arrow keys to move between “User” and

“Engineer”.

4. Select “Engineer” and then press enter to

confirm your selection .

Engineer mode has been set up

Commissioning

2.2.2 Direct connection between the PC and the E-RMA

LAN

One option for using your generator with E-RMA LAN module is to make a

direct connection between your generator and your PC. In this case you

should connect the E-RMA LAN module directly to your PC or your laptop.

Proceed as described in the following.

NOTICE!

You must configure your local network on the PC as follows in order to be

able to use the direct connection between the E-RMA LAN and the PC:

► IP address: 192.168.1.10

► Subnet mask: 255.255.255.0

► Gateway IP: 192.168.1.1

NOTICE!

When all of the settings have been entered successfully, you should then

deactivate Engineer mode to prevent any incorrect settings from being en-

tered.

► Now proceed as explained in Chapter 2.2.1 Activating “Engineer” mode. Now

return to User mode again instead of using Engineer mode.

Conditions Integrated and switched on E-RMA LAN module

Network has been configured on your PC

1. Press the Page button.

2. Now select the “Password” option

in the menu.

3. Set up the controller password and

the access code to 0.

This password was previously con-

figured in the factory.

4. Return to the menu and then select

the “CommsSettings” option.

5. Press Enter to confirm and open

the next menu.

6. Use the arrow keys to go to the “IB-

Lite IP Adrr” option.

7. Now check its IP address.

The default setting should be

192.168.1.254. If this is not the

case, change the IP address ac-

cordingly.

8. Now go to the IBLite DHCP and

then the AirGate options in the

same menu.

9. These two menu options must be

DISABLED.

Commissioning

Connect your computer to the E-RMA LAN module after you have complet-

ed the settings listed above. Do this by attaching the previously connected

LAN cable to your PC.

The following options are available for establishing a connection between the E-

RMA LAN module and your PC:

1. You can use the free-of-charge “InteliMonitor” software.

a) This can be downloaded free-of-charge from the following internet page:

https://www.comap-control.com/products/detail/intelimonitor

b) You will need to create an account to download the software and this can

also be created free-of-charge.

2. Enter the IP address 192.168.1.254 in the address bar in your browser.

a) The integrated SCADAW web server will set up a connection with the E-

RMA LAN module.

You can now use the E-RMA LAN module’s various functions from your PC.

2.2.3 Connection from the E-RMA LAN via the internet us-

ing a dynamic IP

It is also possible to connect the E-RMA LAN module with the Ethernet / in-

ternet using a dynamic IP address and AirGate. In this case you must con-

nect your E-RMA LAN module to a router or an Ethernet / internet socket.

NOTICE!

Use this option when no static Ethernet IP address was assigned by your

IT department or if no static, public IP address was provided by your inter-

net provider.

► Proceed as described in Chapter 2.2.4 Connection from the E-RMA LAN via

the internet using a static IP if you have been assigned a static IP address.

NOTICE!

When all of the settings have been entered successfully, you should then

deactivate Engineer mode to prevent any incorrect settings from being en-

tered.

► Now proceed as explained in Chapter 2.2.1 Activating “Engineer” mode. Now

return to User mode again instead of using Engineer mode.

Conditions Integrated E-RMA LAN module.

Engineer mode has been activated.

Commissioning

2.2.4 Connection from the E-RMA LAN via the internet us-

ing a static IP

The third option for connecting your E-RMA LAN module is via a router us-

ing a static IP address or a public, static IP address. The public, static IP

address can be obtained from your internet provider.

NOTICE!

Only use this option if you have been given a static Ethernet IP address by

your IT department or if a static, public IP address has been provided by

your internet provider.

NOTICE!

When all of the settings have been entered successfully, you should then

deactivate Engineer mode to prevent any incorrect settings from being en-

tered.

► Now proceed as explained in Chapter 2.2.1 Activating “Engineer” mode. Now

return to User mode again instead of using Engineer mode.

Integrated E-RMA LAN module.

Engineer mode has been activated.

1. Press the Page button.

2. Now select the “Password” option

in the menu.

3. Set up the controller password and

the access code to 0.

This password was previously con-

figured in the factory.

4. Return to the menu and then select

the “CommsSettings” option.

5. Press Enter to confirm and open

the next menu.

6. Now go to the IBLite DHCP and

then the AirGate options in the

same menu.

7. These two menu options must be

ENABLED.

8. Use airgate.comap.cz to configure

the AirGate IP option.

9. Now close this menu and return to

the main screen.

10. Use the arrow keys to go to the

menu shown on the left and note

down the AirGate ID.

You can connect your generator to your router after you have completed these

settings. Register your generator with the web supervisor so that you can ac-

cess your generator. Now proceed as explained in Chapter 4 .

Commissioning

1. Press the Page button.

2. Now select the “Password” option

in the menu.

3. Set up the controller password and

the access code to 0.

This password was previously con-

figured in the factory.

4. Return to the menu and then select

the “CommsSettings” option.

5. Press Enter to confirm and open

the next menu.

6. Now use the arrow keys to go to

the IBLite IP Addr, IBLite NetMask

and IBLite GateIP menu options.

7. Configure these three options ac-

cording to the specifications given

to you by your IT department or the

details provided by your Internet

service provider.

8. The “IBLite DHCP and “AirGate“

options must be DISABLED.

9. Now close this menu and return to

the main screen.

You can connect your generator to your router after you have completed these

settings. Register your generator with the web supervisor so that you can ac-

cess your generator. Now proceed as explained in Chapter 4 .

Indice

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente