Endress+Hauser RIA15 Manuale utente
Operating Instructions
RIA15
Process display unit
Loop-powered 4 to 20 mA process display unit
BA01073K/09/EN/02.12
71207036
Valid as of version
01.00.xx
RIA15 Table of contents
Endress+Hauser 3
Table of contents
1 Important document
information ............. 4
1.1 Document function ............ 4
1.2 Document conventions .......... 4
2 Safety instructions ........ 6
2.1 Requirements for the personnel ..... 6
2.2 Designated use .............. 6
2.3 Workplace safety ............. 7
2.4 Operational safety ............. 7
2.5 Product safety ............... 7
3 Identification ............ 8
3.1 Nameplate ................. 8
3.2 Scope of delivery ............. 8
3.3 Certificates and approvals ........ 8
4 Installation .............. 9
4.1 Incoming acceptance, transport,
storage ................... 9
4.2 Installation conditions .......... 9
4.3 Installation instructions ......... 10
4.4 Post-installation check ......... 13
5 Wiring ................ 13
5.1 Quick wiring guide ........... 13
5.2 Inserting the cable, field housing .... 15
5.3 Connecting to potential equalization .. 16
5.4 Grounding ................ 16
5.5 Degree of protection ........... 17
5.6 Post-connection check ......... 17
6 Operation ............. 18
6.1 Operating functions ........... 19
7 Commissioning ......... 19
7.1 Post-installation check and switching
on the device .............. 19
7.2 Operating matrix ............ 19
8 Troubleshooting ......... 21
8.1 Error limits as per NAMUR ....... 21
8.2 Diagnostic messages ........... 22
8.3 Spare parts ................ 23
9 Maintenance ........... 23
10 Return ................ 23
11 Disposal ............... 24
12 Technical data .......... 24
Important document information RIA15
4 Endress+Hauser
1 Important document information
1.1 Document function
These Operating Instructions contain all the information that is required in various phases of
the life cycle of the device: from product identification, incoming acceptance and storage, to
mounting, connection, operation and commissioning through to troubleshooting, maintenance
and disposal.
1.2 Document conventions
1.2.1 Safety symbols
Symbol Meaning
DANGER
A0011189-EN
DANGER!
This symbol alerts you to a dangerous situation. Failure to avoid this situation will result in
serious or fatal injury.
WARNING
A0011190-EN
WARNING!
This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in
serious or fatal injury.
CAUTION
A0011191-EN
CAUTION!
This symbol alerts you to a dangerous situation. Failure to avoid this situation can result in
minor or medium injury.
NOTICE
A0011192-EN
NOTICE!
This symbol contains information on procedures and other facts which do not result in
personal injury.
1.2.2 Electrical symbols
Symbol Meaning
A0011197
Direct current
A terminal to which DC voltage is applied or through which direct current flows.
A0011198
Alternating current
A terminal to which alternating voltage is applied or through which alternating current flows.
A0017381
Direct current and alternating current
• A terminal to which alternating voltage or DC voltage is applied.
• A terminal through which alternating current or direct current flows.
A0011200
Ground connection
A grounded terminal which, as far as the operator is concerned, is grounded via a grounding system.
A0011199
Protective ground connection
A terminal which must be connected to ground prior to establishing any other connections.
A0011201
Equipotential connection
A connection that has to be connected to the plant grounding system: This may be a potential
equalization line or a star grounding system depending on national or company codes of practice.
RIA15 Important document information
Endress+Hauser 5
1.2.3 Symbols for certain types of information
Symbol Meaning
A0011182
Allowed
Indicates procedures, processes or actions that are allowed.
A0011183
Preferred
Indicates procedures, processes or actions that are preferred.
A0011184
Forbidden
Indicates procedures, processes or actions that are forbidden.
A0011193
Tip
Indicates additional information.
A0011194
Reference to documentation
Refers to the corresponding device documentation.
A0011195
Reference to page
Refers to the corresponding page number.
A0011196
Reference to graphic
Refers to the corresponding graphic number and page number.
,…
,
Series of steps
ÃResult of a sequence of actions
A0013562
Help in the event of a problem
1.2.4 Symbols in graphics
Symbol Meaning
1, 2, 3,... Item numbers
,…
,
Series of steps
A, B, C, ... Views
A-A, B-B, C-C, ... Sections
A0013441
Flow direction
-
A0011187
Hazardous area
Indicates a hazardous area.
.
A0011188
Safe area (non-hazardous area)
Indicates a non-hazardous area.
Safety instructions RIA15
6 Endress+Hauser
1.2.5 Tool symbols
Symbol Meaning
A0011220
Flat blade screwdriver
A0011221
Allen key
A0011222
Open-ended wrench
A0013442
Torx screwdriver
2 Safety instructions
2.1 Requirements for the personnel
The personnel for installation, commissioning, diagnostics and maintenance must fulfill the
following requirements:
►Trained, qualified specialists must have a relevant qualification for this specific function and
task
►Are authorized by the plant owner/operator
►Are familiar with federal/national regulations
►Before beginning work, the specialist staff must have read and understood the instructions
in the Operating Instructions and supplementary documentation as well as in the
certificates (depending on the application)
►Following instructions and basic conditions
The operating personnel must fulfill the following requirements:
►Being instructed and authorized according to the requirements of the task by the facility's
owner-operator
►Following the instructions in these Operating Instructions
2.2 Designated use
The process display unit displays analog process variables on its screen.
The device is powered via the current loop and does not require an additional power supply.
RIA15 Safety instructions
Endress+Hauser 7
• The manufacturer accepts no liability for damages resulting from incorrect use or use other
than that designated. It is not permitted to convert or modify the device in any way.
• Panel-mounted device:
The device is designed for installation in a panel and must only be operated in an installed
state.
• Field device:
The device is designed for installation in the field.
•The device may only be operated under the permitted ambient conditions (® ä 25).
2.3 Workplace safety
For work on and with the device:
►Wear the required personal protective equipment according to federal/national regulations.
2.4 Operational safety
Risk of injury.
►Operate the device in proper technical condition and fail-safe condition only.
►The operator is responsible for interference-free operation of the device.
Conversions to the device
Unauthorized modifications to the device are not permitted and can lead to unforeseeable
dangers.
►If, despite this, modifications are required, consult with Endress+Hauser.
Repair
To ensure continued operational safety and reliability,
►Carry out repairs on the device only if they are expressly permitted.
►Observe federal/national regulations pertaining to repair of an electrical device.
►Use original spare parts and accessories from Endress+Hauser only.
Environmental requirements
If a plastic transmitter housing is permanently exposed to certain steam and air mixtures, this
can damage the housing.
►If you are unsure, please contact your Endress+Hauser Sales Center for clarification.
►If used in an approval-related area, observe the information on the nameplate.
2.5 Product safety
This measuring device is designed in accordance with good engineering practice to meet state-
of-the-art safety requirements, has been tested, and left the factory in a condition in which
they are safe to operate.
It meets general safety standards and legal requirements. It also complies with the EC
directives listed in the device-specific EC Declaration of Conformity. Endress+Hauser confirms
this by affixing the CE mark to the device.
Identification RIA15
8 Endress+Hauser
3 Identification
3.1 Nameplate
The nameplate is located on the right-hand side of the housing in the case of the field device,
and on the rear of the housing in the case of the panel-mounted device.
Ord. cd.: XXXXXXXX
Ser. no.: XXXXXXXXXXXXXXXXX
Ext. ord. cd.: RIA15-XXXXXXX
Ta= -40...+60°C
Front IP65 Type 4X Encl.
Loop powered 4...20 mA
Umax 30V Imax 100mA
RIA15
Made in Germany 2012
D-87484 Nesselwang
1
2
3
4
5
6
7
8
9
Class2 circuit or SELV circuit
A0018814
å 1 Nameplate of the process display unit (example)
1 Order code of the device 6 Approvals (optional)
2 Serial number of the device 7 Power supply
3 Manufacturer's address 8 Input signal
4 Ambient temperature range 9 Housing degree of protection
5 Device designation
3.2 Scope of delivery
The scope of delivery of the device comprises:
• Panel-mounted device
– Process display unit
– Operating Instructions
– Ex Safety Instructions (optional)
– Fastening fixtures
• Field device
– Process display unit
– Operating Instructions
– Ex Safety Instructions (optional)
– Fastening fixtures for wall/pipe mounting (optional)
– Weather protection cover (optional)
3.3 Certificates and approvals
An overview of all the approvals available is provided in the "Technical data" section.
CE mark, Declaration of Conformity
RIA15 Installation
Endress+Hauser 9
The device is designed to meet state-of-the-art safety requirements, has been tested, and left
the factory in a condition in which it is safe to operate. The device complies with the
applicable standards and regulations in accordance with EN 61010-1 "Safety requirements for
electrical equipment for measurement, control and laboratory use".
The device described in these Operating Instructions therefore complies with the statutory
requirements of the EU Directives. The manufacturer confirms that the device has been
successfully tested by applying the CE mark.
4 Installation
4.1 Incoming acceptance, transport, storage
Compliance with the permitted environmental and storage conditions is mandatory. Precise
specifications are provided in the "Technical data" section (® ä 24).
4.1.1 Incoming acceptance
On receipt of the goods, check the following points:
• Is the packaging or the content damaged?
• Is the delivery complete? Compare the scope of delivery against the information on your
order form.
4.1.2 Transport and storage
Please note the following:
• Pack the device so that is protected against impact for storage and transport. The original
packaging provides optimum protection.
• The permitted storage temperature is –40 to +85 °C (–40 to +185 °F); it is possible to store
the device at borderline temperatures for a limited period (48 hours maximum).
4.2 Installation conditions
At temperatures below –25 °C (–13 °F) the readability of the display can no longer be
guaranteed.
4.2.1 Display unit in the panel-mount housing
Permitted ambient temperature range –40 to 60 °C (–40 to 140 °F), horizontal orientation.
IP65 protection at front, IP20 at rear
See "Technical data" section (® ä 24).
4.2.2 Display unit in the field housing
Permitted ambient temperature range –40 to 60 °C (–40 to 140 °F). IP66 protection, NEMA
4x.
See "Technical data" section (® ä 24).
Installation RIA15
10 Endress+Hauser
4.3 Installation instructions
See the "Technical data" section for the dimensions of the device (® ä 27).
4.3.1 Panel housing
2mm
A0017762
å 2 Installation instructions for the panel housing
Installation in a panel with a panel cutout 92x45 mm (3.62x1.77 in.), max. panel thickness
13 mm (0.51 in).
1. Slot the device into the panel cutout from the front.
2. Fit the mounting clips on the side of the housing and tighten the threaded rods.
4.3.2 Field housing
Pipe mounting (with optional mounting kit)
The device can be mounted on a pipe with a diameter of up to 50.8 mm (2 in) with the
mounting kit (optionally available).
Altri manuali per RIA15
6
Indice
Altri manuali Endress+Hauser Strumento di misura
Endress+Hauser
Endress+Hauser Levelflex M FMP43 Manuale utente
Endress+Hauser
Endress+Hauser Micropilot FMR62 Manuale
Endress+Hauser
Endress+Hauser SpectraSensors OXY5500 Manuale utente
Endress+Hauser
Endress+Hauser Liquiline CM44 series Manuale dell'operatore
Endress+Hauser
Endress+Hauser Cleanfit W CPA450 Manuale utente
Endress+Hauser
Endress+Hauser Proline Prosonic Flow 92F Series Istruzioni per l'installazione
Endress+Hauser
Endress+Hauser Nivotester FailSafe FTL825 Manuale utente
Endress+Hauser
Endress+Hauser Proline Promag 50 Specifiche tecniche
Endress+Hauser
Endress+Hauser Proline Promass 200 Istruzioni per l'installazione
Endress+Hauser
Endress+Hauser Proline Promag W 400 Manuale
Endress+Hauser
Endress+Hauser Deltapilot S FMB70 Istruzioni per l’uso
Endress+Hauser
Endress+Hauser Proline Promag W 500 Manuale utente
Endress+Hauser
Endress+Hauser Proline Promag W 500 Manuale
Endress+Hauser
Endress+Hauser EngyCal RH33 Specifiche tecniche
Endress+Hauser
Endress+Hauser Micropilot FMR51 Manuale
Endress+Hauser
Endress+Hauser Proline Promag W 400 HART Manuale utente
Endress+Hauser
Endress+Hauser Levelflex M FMP40 Manuale utente
Endress+Hauser
Endress+Hauser SpectraSensors SS2100 Aggiornamento firmware
Endress+Hauser
Endress+Hauser Proline Promag P 100 Manuale utente
Endress+Hauser
Endress+Hauser Proline Prowirl C 200 Specifiche tecniche
