Envirovent MEV SPIDER Manuale utente

SHOULD YOU ENCOUNTER ANY PROBLEMS INSTALLING THIS UNIT CALL

01 Introduction

You are about to install a product that is designed to outlast

the life-cycle of the building. Once installed the unit will operate

continuously for 5 years and beyond without a major service.

Please therefore ensure that this product is treated with care

and installed properly i.e. for the life of the building. If the unit

is mishandled you might break it! This invalidates the warranty.

And remember, if you have any problems please call our

dedicated Technical Team. We are always pleased to help and

in an emergency will come out to site quickly, completely free

of charge.

Thank you for choosing EnviroVent

The fastest growing ventilation company in the UK

HOTLINE: 0845 27 27 810

Due to our policy of continuous innovation and improvement EnviroVent

reserves the right to alter products specication and appearance without

notice.

AFTER INSTALLING THIS UNIT PLEASE PASS ONTO END USER

DO NOT THROW AWAY

02 About The Unit

EXPLODED VIEW

Lid

Electronics assembly

Black box

Ø100 input

Ø125 spigot

extract to atmosphere

The EnviroVent MEV Spider is a low-energy,

continuous mechanical extract ventilation

system designed with multiple extract

points to simultaneously draw moisture-

laden air out of the wet rooms, whilst

minimising the migration of humidity to other

rooms. The extract unit is centrally located

in, for example, a hallway cupboard, with

ducts running from the unit to the kitchen,

bathroom, en-suite and other wet zones.

The unit is suitable for houses, apartments

and communal residences with kitchen plus

up to 6 additional wet rooms, providing high

centrifugal performance with low running

noise. Highly cost eective and value for

money, the MEV Spider comes with a full

ve year guarantee.

Commissioning panel

Fan scroll and fan

SHOULD YOU ENCOUNTER ANY PROBLEMS INSTALLING THIS UNIT CALL

03 Wiring Diagram

Electrical Connections

The appliance must be earthed and a double pole switch having a minimum contact separation

of 3.0mm must be used to provide isolation for the unit. All wiring must be completed by a

qualied electrician. This appliance is suitable for 230V ~ 50Hz single phase supply fused at 3

amps. The appliance is supplied with a 3 core mains exible cable.

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or

similarly qualied persons in order to avoid a hazard.

Emergency shutdown details - Unit to be isolated from the mains by turning it o at

the isolating switch.

After Sales Service - We recommend you do not dismantle or remove any other parts

than those mentioned, as any tampering would automatically cancel the guarantee. If

you detect any fault please contact EnviroVent.

Remote control version (MEVS-W) Humidity and standard versions

(MEVS-H, MEVS)

AFTER INSTALLING THIS UNIT PLEASE PASS ONTO END USER

DO NOT THROW AWAY

Supply Voltage 230V / 50-60Hz / 70W Max / 0.5 A Max

Dimensions H 387mm x W 440mm x D 198mm

Ventilation Capacity 135 l/s @ 100pa. Max 151 l/s (545m3/h)

Weight Boxed 5.8kg | Unit 4.3kg

04 Technical Specications

Performance Curve

Dimensions (mm)

198

300

Ø125

380

440

357

SHOULD YOU ENCOUNTER ANY PROBLEMS INSTALLING THIS UNIT CALL

05 Installation Instructions

IMPORTANT

Be sure to have read and understood these

instructions before beginning the installation

process.

PRE-INSTALLATION CHECK LIST

Make sure that the unit can physically t in to

the desired location.

The MEV Spider unit should be situated so

that access for maintenance or replacement

of parts is possible. Make the ductwork runs

as short as possible. Having the most direct

route and using as few bends as possible

will reduce air resistance and improve the

eciency of the unit.

SAFETY AND RECOMMENDATIONS

• All wiring must comply with Building

Regulations and the current I.E.E. Wiring

Regulations (BS7671) or the equivalent

standards for your country. The nal

installation should be examined and tested

by a qualied electrician.

• Precautions must be taken to avoid the

back-ow of gases into the dwelling from

the open ue of gas or other fuel-burning

appliances.

• Make sure the mains supply complies with

the rating label for voltage, frequency and

phase.

• This appliance can be used by children

aged from 8 years and above and

persons with reduced physical, sensory or

mental capabilities or lack of experience

and knowledge if they have been given

supervision or instruction concerning

use of the appliance in a safe way and

understand the hazards involved. Children

shall not play with the appliance. Cleaning

and user maintenance shall not be made

by children without supervision.

AFTER INSTALLING THIS UNIT PLEASE PASS ONTO END USER

DO NOT THROW AWAY

05 Installation Instructions

Description Quantity Item

MEV Spider Unit 1x

Spigots 3x

Spigot Blank 1x

Fixing Kit 1x

Screws 8G X 2.0” 4x

Washers 4x

Plasterboard Plugs 4x

Adhesive Foam Pads 4x

Controls

Intelligent Humidity Tracking (Automatic)

MEVS-H and MEVS-W versions only

When the MEV unit senses a rise in humidity,

caused by increased moisture generation such

as through cooking or showering, the extract

and supply airows will slowly begin to increase

in direct proportion to the increase in humidity.

It will then automatically track back down again

when humidity falls. This controls condensation

quietly and eciently.

Boost - Wall Switch

The MEVS and MEVS-H comes with a boost

switch as standard to activate boost when

required. The unit will remain at boost for as

long as the switch is on.

Boost - Remote Control

MEVS-W units come with a remote control

switch to activate boost. The unit remains

at boost for 20 mins. See page 9 for further

information.

SHOULD YOU ENCOUNTER ANY PROBLEMS INSTALLING THIS UNIT CALL

Mounting the unit

1. The unit maybe installed in any vertical or

horizontal orientation

2. Use the unit to mark xing holes, ensuring

clearance around the MEV unit. Drill 4 x

Ø8mm holes, position plasterboard plugs

in the mounting surface and foam pads

on the back of the unit’s mounting tabs.

4. Secure the MEV unit on all four corners.

5. Electrical connections (see page 3).

05 Installation Instructions

Adhesive

foam pad

Washer

Screw

Plasterboard

plugs

AFTER INSTALLING THIS UNIT PLEASE PASS ONTO END USER

DO NOT THROW AWAY

Connecting the ductwork

1. Scribe around the outer edge of the

required spigot blank MAX x 3 (a). Knock

out the blank with a light tap (b).

2. Remove blanks from inside the unit.

3. It may be necessary to remove excess

material with a knife.

4. Push in spigot and x with self tapping

screws provided.

5. Ductwork, ridged and exi must be

securely xed.

6. If a blank is removed in error, the spigot

hole must be lled with the spare blank

provided. Firmly glue in place.

05 Installation Instructions

(a)

(b)

SHOULD YOU ENCOUNTER ANY PROBLEMS INSTALLING THIS UNIT CALL

06 Commissioning

Boost controls

The MEV Spider operates continuously

on ‘Normal’ setting to ensure the home is

ventilated at the appropriate level although

you can boost the system via the wired or

remote control switch, if tted.

For remote control switches, press the

button once, the green LED will light up and

the unit will go to boost. The boost time is

set to 20 minutes as standard. When the

battery requires changing, unscrew the

switch front cover. The battery is located

on the back of the cover. Battery type - 3V

Lithium, CR2032.

To pair additional remote control units

(RC units only)

1. Insert insulated point into hole A to contact

push button

2. Press for 5 seconds until unit LED ashes,

then release

3. Press remote control button and the

green LED will light up

4. RC is now paired

Remote control

Remote control button

Flashing red

LED = not paired

Constant green

LED = paired

LED

Hole A

Altri manuali per MEV SPIDER

Indice

Altri manuali Envirovent Fan

Envirovent

Envirovent ATMOS WALL Manuale utente

Envirovent

Envirovent ECO DMEV+ LC Manuale utente

Envirovent

Envirovent energiSava 300 Manuale utente

Envirovent

Envirovent PIV Manuale utente

Envirovent

Envirovent SABIK 350 Manuale utente

Envirovent

Envirovent fliterless infinity fan 230v Guida rapida

Envirovent

Envirovent PROFILE-100 Istruzioni per il montaggio

Envirovent

Envirovent SILENT MV Series Istruzioni per il montaggio

Envirovent

Envirovent MEV SPIDER Manuale utente

Envirovent

Envirovent SLIMLINE 300 Guida rapida

Envirovent

Envirovent energiSava 200 Manuale utente

Envirovent

Envirovent IPX4 Manuale utente

Envirovent

Envirovent Eco dMEV+ Manuale utente

Envirovent

Envirovent Silent-100 Design Manuale

Envirovent

Envirovent PIV Manuale utente

Envirovent

Envirovent FILTERLESS EXTRACT FAN SELV Series Guida rapida

Envirovent

Envirovent filterless extractor fan Manuale utente

Envirovent

Envirovent OZEO Manuale utente

Envirovent

Envirovent SILENT MV-160/100 Istruzioni per il montaggio

Envirovent

Envirovent energisava250 Manuale utente

Envirovent

Envirovent POWER-170 Istruzioni per il montaggio

Envirovent

Envirovent ECO DMEV Manuale utente

Envirovent

Envirovent energisava 380 Manuale utente

Envirovent

Envirovent fliterless infinity fan 230v Manuale utente

Manuali Fan popolari di altre marche

ELTA FANS

ELTA FANS H03VV-F Manuale utente

Hunter

Hunter 20714 Manuale di istruzioni

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manuale utente

Hunter

Hunter Caraway Manuale di istruzioni

Panasonic

Panasonic FV-15NLFS1 Manuale utente

Kompernass

Kompernass KH 1150 Manuale utente

VES

VES FALA100/12V/TR Manuale utente

Vertiv

Vertiv Liebert DCD Manuale utente

Westinghouse

Westinghouse GFP Series Manuale utente

Venmar

Venmar KUBIX HRV PLUS Series Manuale utente

Maico

Maico ECR 31 Manuale utente

Sonnenkonig

Sonnenkonig Dinky Manuale utente

S&P

S&P ECOWATT HXBR Manuale utente

Wider

Wider IMP03369BH Manuale utente

Panasonic

Panasonic F-60DHN Manuale utente

Hinkley

Hinkley HIGHLAND Manuale utente

Broan

Broan 766BN Manuale utente

Premium

Premium PFS16022 Istruzioni per il montaggio