EOS ECON F1 Manuale utente

Druck Nr. 29343282en/ - 37.06

Assembly and Operating

Instructions

ECON F1

IP x4

Contents

1. Installation of the control unit .................................................................... 12

2. Electrical installation ............................................................................... 13

3. Operation ................................................................................................. 14

3.1 Start-up .................................................................................................... 15

3.2 Switching on the unit for the first time ...................................................... 15

3.3 Manual Selection of Light Color ................................................................ 15

3.4 Automatic Selection of Light Color ........................................................... 15

5. Wiring diagram ......................................................................................... 17

Technical specifications

Supply voltage: 230 V 1N AC 50 Hz

Fuse protection: 1 x 10 A

Lamp capacity: 400 W max.

Surrounding temperature: 0 to 40° C

Type of protection: IP X4

Color sequence when in red - red/yellow - yellow - yellow/green - green - green/

Automatic mode: blue - blue - blue/red

Color overlap period: 0 seconds

Cycle time: adjustable from 1 to 10 minutes

Dimensions (H x W x D): 210 x 270 x90 mm

Weight: ca. 1 kg

english

10 min.

1. Installation of the control unit

Before the control unit can be fastened to

the outer wall of the cabin, the covering of

the control unit must be removed. For this,

the two mounting screws (Illust. 1) are

loosened. These screws are attached

beneath the control panel dials as captive

screws, but may be screwed open and

closed through the visible holes in the

operating panel with a small Phillips

screwdriver. After the screws are loosened,

the cover is removed.

For practical purposes, the control unit

should always be fastened to the outer wall

of the cabin near the sauna control unit.

If this is desired, please observe that most

sauna cabins have already been equipped

with cable conduits for electrical wiring; in

this case, the position of the control unit is

pre-determined. For the mounting of the

control unit, the mounting holes Æ 3 are

drilled in accordance with the dimensions

given in Illust. 3, and one of the provided

wood screws 4 x 20, see Illust. 3.1, is

screwed into the wood through the upper

middle hole, leaving a 3mm section of the

screw projecting out from the wall. The

lower part of the control unit is hooked onto

this wood screw by its upper mounting hole.

Finally all connecting lines - see Illust. 4 -

are conducted through the respective feed-

through channels into the control unit.

Illust. 1

Illust.2

The colored light control units are delivered equipped for a voltage of 230 V 50 Hz

as a standard and must be separately fuse protected against 10 A.

Installation and connection of the sauna systems and other electrical

equipment may be undertaken only by a expert; this is subject to VDE 0100,

Part 703/2006-2

Sauna systems may be connected to the power supply only by hard wire.

For trouble-free operation of your sauna system, please read the following

installation and user's guide thoroughly.

mountingscrews

Controlbuttons

Supplyline

color lighting

Control unit

Colored light unit

english

Feed-throughchannel

for power supply lines

Illust.4

Mounting hole

Feed-throughchannel

for lamp

Illust.3.2

Illust.3.1

Illust.3

The lower part is finally fastened to the

cabin wall through the two lower pre-drilled

holes.

If the sauna cabin is not equipped with

cable conduits for connecting lines, these

lines must be laid visibly on the cabin wall.

For this, the three mounting holes are pre-

drilled also, as shown in Illust. 3. Finally,

align the bottom part of the control unit over

the drilled holes and sketch the right-hand

feed-through hole for the control lines onto

the cabin wall. Drill a 10 mm feed-through

hole at this position. CAUTION! This hole

is needed only if you want to use the

continuous color switching option (see

start-up).

Because the connecting lines must be laid

between the control unit and the cabin wall

in this type of installation, for practical

purposes in a recess of the grooved

panels, the control unit must be installed

in such a way as to provide for adequate

clearance. For this purpose, 3 spacer

tubes are provided with the control unit.

Using these tubes, the lower part is

installed to provide for this clearance as

shown in Illust. 3.2. After the connecting

lines are fed through the respective feed-

through channels into the control unit, bolt

the lower part, again with help of the

spacers, into the lower mounting holes on

the cabin wall.

2. Electrical installation

The electrical installation may be

undertaken only by an authorized electrician

subject to the regulations of the local po-

wer utility company and the VDE.

The 3-wire power supply lead is brought to

the control unit and connected, as can be

seen in Illust. 2. A wiring diagram is posted

in the area of the main terminals.

CAUTION: The colored lights are

connected by relay contacts and are not

fuse-protected internally. Install a 3 x 1,5

mm² hardwire connection with a fuse

protection of 10 A.

Mountingholes

english

10 min.

Button functions

ON/OFF switch

Single color and automatic mode

Program button

Adjustment buttons

Operation

Ready LED

1 - 10 LEDs for color sequence time

ReadyLED

english

Illust.6

LEDsforcolor LEDsforcolorsequencetime

ON/OFFswitch Singlecolorand

automaticmode

Programbutton

Adjustment

buttons

Automatic Selection of Light Color

Press the light button to activate

automatic selection of the light color.

During automatic operation 5 LED's

illuminate for an operating time of 5

minutes.

When the light color selection is switched

to automatic the color sequence is red-

red/yellow-yellow-yellow/green-green-

green/blue-blue-blue/red. In the basic

mode the individual colors are held for 5

minutes and the mixed colors for 10

seconds (see "Default Parameters")

The holding time can be set within the

range of 1 min. and 10 min. The row of

LED's starts to flash when the -

button is pressed.

The time can be changed with the

and buttons.

Pressing the -button again confirms

the value set and the corresponding

number of LED's illuminates in the row

of LED's (5 minutes = 5 LED's, 10

minutes = 10 LED's, etc.)

The holding time for mixed colors can

be set to 10 seconds (default setting) or

to the operating time for the individual

colors:

Press the - and -buttons

simultaneously and hold for 2 seconds

until the row of LED's flashes

momentarily. Reset by pressing again.

The parameters set last remain set as

long as the control is not separated from

the line power.

Start-up

After checking all connections again,

connect the unit to the line power by

switching on the circuit breakers and/or

main switch. The green LED above the

-symbol signals that the unit is

ready for operation.

Switching on the unit for the first

time

Pressing the Start/Stop button , for

the first time after connecting the power

supply switches the unit to its ready

mode. The red LED on the colored light

unit and the red LED on the control unit

illuminate.

Default Parameters

OManual colored light selection

OOperating time for individual colors in

automatic mode: 5 min.

OOperating time for mixed colors in

automatic mode: 10 sec.

Manual Selection of Light Color

It is possible to select between individu-

al colors and mixed colors with the

and buttons.

english

Effect of Colors

The psychological influence of the colors

is perceived by the eyes. From there the

color radiation is transferred to the brain in

a complex process, where it develops its

effect in the form of certain impressions

and energy.

The colors affect the nervous system

vitalizing the body's resistance. Certain

body systems are activated depending

on the type of color.

Physical absorption takes place

primarily over the skin through direct

radiation of the colors.

Chemical absorption takes place in the

gasto-intestinal tract in the form of a

mixed diet in all colors.

BLUE, the color of the sky and water, is

connected with longing, vastness and

coolness. Coolness retards human

functions, the reason why blue is calming

and relaxing and can help alleviate

nervous disorders, insomnia,

restlessness and fear.

GREEN is the color of nature. Green light

soothes and inspires simultaneously. It

provides relaxation and regeneration.

Green light is reputed to have a positive

effect on the bronchi and lungs and to

be helpful for nervous disorders,

headache and inflammation of the joints.

YELLOW is said to intensify a positive

vital attitude and increase general well-

being. Yellow colors can stimulate and

fortify the nerves and dispel gloom and

melancholy, gastro-intestinal disorders

can be compensated.

RED is associated with fire and blood.

The color for activity, vitality and warmth.

Red is reputed to stimulate circulation

and therefore contribute to a general

increase in well-being and vitality

english

Connection Schematic

Observecodingoffeed lines

tocoloredlightunit

Wiringcodes: green/yellow =PE

1=N

2 = red

3 =yellow

4 =green

5 =blue

Electronic

circuitry

Colored light unit

Line power feed

3 x 1.5 mm²

230 V/50 Hz

Illust.7

english

2345 1

Attention!

Dear customer,

according to the valid regulations, the

electrical connection of the sauna heater

and the control box has to be carried out

through the specialist of an authorized

electric shop.

We would like to mention to the fact that

in case of a warrenty claim, you are kindly

requested to present a copy of the invoice

of the executive electric shop.

english

Guarantee

The guarantee is taken over according to the

legal regulations at present.

Manufacturer’s warrenty

- The period of warrenty starts from the date

of purchase and lasts up to 2years for

commercial use and 3 years for private use.

- Always include the completed warrenty

certificate when returning equipment.

- The warrenty expires for appliances which

have been modified without manufacturer’s

explicit agreement.

- Damages caused by incorrect operation or

handling through non-authorized persons are

not covered under the terms of warranty.

- In the event of a claim, please indicate the

serial number as well as the article code

number and type name with expressive

description of the fault.

- This warrenty covers damaged parts but no

defects due to wear and tear.

In case of complaint please return the equipment

in its original packaging or other suitable

packaging (caution: danger of transport damage)

to our service department.

Always include the completed warrenty

certificate when returning equipment.

Possible shipping costs arising from the transport

to and from point of repair cannot be borne by

us.

Outside of Germany please contact your

specialist dealer in case of warranty claims.

Direct warranty processing with our service

department is in this case not possible.

Equipment start-up date:

Stamp and signature of the authorized

electrician:

Service address:

EOS-Werke Günther GmbH

Adolf-Weiß-Str. 43

35759 Driedorf-Germany

tel +49 (0) 2775 82 240

fax +49 (0) 2775 82 455

[email protected]

www.eos-werke.de

Indice

Altri manuali EOS Unità di controllo

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente