EPOX 6VBA-E Manuale utente

TRADEMARK

All products and company names are trademarks or registered

trademarks of their respective holders.

These specifications are subjected to change without notice.

Manual Revision 4.2

May 25, 1999

6VBA-E

A PA P

A Pentiumentium

entiumentium

entium®®

®®

®II or PII or P

II or PII or P

II or Pentiumentium

entiumentium

entium®®

®®

®IIIIII

IIIIII

III

Slot1 Processor based AGPSlot1 Processor based AGP

Slot1 Processor based AGP

motherboard (100/66MHz)

SupporSuppor

Supports PC-133 SDRAM Modulets PC-133 SDRAM Module

ts PC-133 SDRAM Modulets PC-133 SDRAM Module

ts PC-133 SDRAM Module

Features

6VBA-E

Page 2

FEATURES

6VBA-E Features:

•6VBA-E is based on the Pentium®II/III Processor operating at 266 ~

550MHz on Slot1. The board is configured by an ESSJ (Easy-Setting-

Single-Jumper) to match your CPU clock speed.

•Designed with VIA Apollo Pro PCIset.

•Supports up to 768MB of DRAM (minimum of 8 MB) on board

•6VBA-E will support Error Checking and Correcting (ECC) when using

parity SDRAM memory modules. This will detect multiple bit errors and

correct 1-bit memory errors.

•Supports (1) 16 bit ISA slots, (5) 32 bit PCI slots, (1) AGP slot, (1) AMR

slot and provides (2) independent high performance PCI IDE interfaces

capable of supporting PIO Mode 3/4 and Ultra DMA 33/66 devices.

The 6VBA-E supports (5) PCI Bus Master slots and a jumperless PCI

INT# control scheme which reduces configuration confusion when plugging

in PCI card(s).

•Supports ATAPI (e.g. CD-ROM) devices on both Primary and Secondary

IDE interfaces.

•Designed with on chip Multi I/O: (1) floppy port, (1) parallel port (EPP,

ECP), and (2) serial ports (16550 Fast UART).

Note: Japanese “Floppy 3 mode” is also supported

•Features Award Plug & Play BIOS. With Flash Memory you can always

upgrade to the current BIOS as they are released. (http://www.2themax.com/

please visit our Technical Support section for the latest updates)

•6VBA-E utilizes a Lithium battery which provides environmental protec-

tion and longer battery life.

Features6VBA-E

Page 3

•Supports the (4) Universal Serial Bus (USB) Ports. The onboard

VT82C686A chip provides the means for connecting PC peripherals such

as; keyboards, joysticks, telephones, and modems.

•Built-in ATX 20-pin power supply connector.

•Software power-down when using Windows®95/98.

•Supports ring-in feature (remote power-on through external modem,

allows system to be turned on remotely.

• Resume by Alarm - Allows your system to turn on at a preselected time.

•Power Loss Recovery - In the event of a power outage your system will

automatically turn itself back on without user intervention.

•Supports CPU Hardware sleep and SMM (System Management Mode).

• Supports Keyboard power ON function (KBPO).

• Built-in WOL (Wake-up On Lan) Connector.

• Built-in AC97 PCI Audio.

Installation6VBA-E

Page 4

Figure 1

6VBA-E Detailed Layout

Installation

6VBA-E

Page 5

Easy Installation Procedure

The following must be completed before powering on your new system:

Configure DIP Switch and Jumper to match your hardware

System memory Configuration

Device Connectors

Configure DIP Switch

We design this motherboard with a DIP Switch to make your install fast and easy.

The following will describe all of the DIP Switch that you are required to set

before moving on to step 2.

Note: The DIP Switch as depicted as shown (Figure 1) in their correct

physical orientation.

1234

1WS)zHM(UPC

1234 oitaRzHM66zHM001

NONONOX3002003

NONOX5.3332053

NONONOX4662004

NONOX5.4003054

NONOX5333005

NOX5.5663055*

NONONOX6004006*

NONOX5.6334056*

NONOX7664*007*

NOX5.7005*057*

NONOX8335*008*

*reserved

JP1 Clear COMS

1-2 : Run Mode(default)

2-3 : Clear CMOS

JP4 Keyboard Power-ON Function Selection

1-2 : Disabled

2-3 : Enabled

Installation6VBA-E

Page 6

System Memory Configuration

Memory Layout

The 6VBA-E supports (3) 168-pin DIMMs (Dual In-line Memory Module).

The DIMMs can be either EDO (Enhanced Data Out) or SDRAM

(Synchronized DRAM).

• DIMM SDRAM may be 83MHz (12ns), 100MHz (10ns) or

125MHz (8ns) bus speed.

• If you use both 50ns and 60ns memory you must configure

your BIOS to read 60ns.

• When using Synchronous DRAM we recommend using the

4 clock variety over the 2 clock.

Figure 2 and Table 1 show several possible memory configurations using both

SIMM and DIMM.

* SDRAM only supports 8, 16, 32, 64, 128, 256MB DIMM modules.

Table 1

DIMM 1

DIMM 2

Bank 0

Bank 1 -Synchronous

-EDO

DIMM 3

Bank 2

yromeMlatoT 1MMID )0knaB( 2MMID )1knaB( 3MMID )2knaB(

BM652= mumixaM

*MARDS/ODE ,BM46,BM23,BM61,BM8 1XBM652,BM821 enoNenoN

BM215=

mumixaM

*MARDS/ODE

,BM46,BM23,BM61,BM8

1XBM652,BM821

*MARDS/ODE

,BM46,BM23,BM61,BM8

1XBM652,BM821 enoN

BM867=

mumixaM

*MARDS/ODE

,BM46,BM23,BM61,BM8

1XBM652,BM821

*MARDS/ODE

,BM46,BM23,BM61,BM8

1XBM652,BM821

*MARDS/ODE

,BM46,BM23,BM61,BM8

1XBM652,BM821

Figure 2

Installation

6VBA-E

Page 7

Device Connectors

Please install the motherboard into the chassis.

Now that your motherboard is installed you are ready to connect all your

connections (figure 10).

J2: Chassis Panel Connector

• Power LED, Speaker, Reset

J3: Turbo LED, HDD LED, IR Conn., Sleep/Power_ON

J4: CPU Fan Power

• A plug-in for the CPU Fan Power

J6: Chassis Fan Power

• A plug-in for the chassis Fan Power

J7: WOL (Wake On Lan) Connector

IDE1: Primary IDE

IDE2: Secondary IDE

FDD1:Floppy Controller Connector

PW1: ATX Power Connector

• 20-pin power connector

CD1: CD Audio Connector

AUX1:AUX Audio Connector

Figure 10

PS/2 Mouse

PS/2

KEYBOARD

USB port

COM1 COM2

parallel port

Speaker

Line_in

MIC

Joystick/Midi port

Installation6VBA-E

Page 8

Device Connectors (continued)

Speaker - Connect to the system's speaker for beeping

1. Speaker 3. GND

2. N/C 4. GND

Reset - Closed to restart system.

Power LED - Power LED connector

1. Power LED(+) 4. NC

2. N/C 5. GND

3. GND

(This is connected to the power button on the case. Using the

Soft-Off by Pwr-BTTN feature, you can choose either Instant

Off (turns system off immediately), or 4 sec delay (you need to

hold the button down for 4 seconds before the system turns off).

When the system is in 4 sec delay mode, there is a special

feature to make the system to go into suspend mode when the

button is pressed momentarily.)

Turbo LED indicator - LED ON when higher speed is selected

IDE LED indicator - LED ON when Onboard PCI IDE Hard

disks is activate

J3 1

IR Connector

1. VCC 4. GND

2. NC 5. IRTX

3. IRRX

Power On/Off

Indice

Manuali Scheda madre popolari di altre marche

DFI

DFI SD170 Manuale utente

ASROCK

ASROCK ROMED8-2T Manuale utente

Asus

Asus P2L97A Manuale utente

Winmate

Winmate IC70 Manuale utente

Asus

Asus MES-B Manuale utente

Grantech

Grantech SYS8F377VGGA-3OMN Manuale utente

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuale utente

Gigabyte

Gigabyte GA-9IVDT Manuale utente

Texas Instruments

Texas Instruments ADS8372EVM Manuale utente

Commell

Commell MS-C73 Manuale utente

IBT Technologies

IBT Technologies MB860 Manuale utente

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuale utente

Biostar

Biostar M7VIT Bravo Istruzioni per l'uso e l'installazione

Intel

Intel D33217CK Manuale utente

Asus

Asus F1A55-M LX PLUS R2.0 Manuale utente

EPC

EPC EPC9147C Manuale utente

Asus

Asus EX-B760M-V5 D4 Manuale utente

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manuale utente