EPOX MVP3E Manuale utente

MVP3E

ISA/PCI/AGP

MotherBoard

with Onboard PCI IDE and Super Multi-I/O.

Apollo MVP3 AGPset

The specification is subject to change without notice.

TRADEMARK

Allproductsandcompanynamesaretrademarksorregistered

trademarksoftheirrespectiveholders.

V034

Introduction

Chapter 1

Introduction

Thismotherboard is a high performance system hardware based on Intel

Pentium processor and is equipped with an AGP slot, four PCI slots, three

standard ISA slots, Super Multi-I/O controller and dual port PCI-IDE

connectors for the future expansion. The hardware dimension is 305mm x

230mm with a four-layer-design technology.

Specification

VIA Apollo MVP3 AGP/PCIset chipset.

Intel Pentium Processor, Pentium Processor with MMX technology, AMD

K5/K6, Cyrix 6x86L/6x86MX & idt C6 operating at 120 ~ 500 MHz with 321

ZIF socket 7 provides scalability to accept faster Processors in the future.

Supports up to 384 MegaBytes of memory (168-Pin DIMM SOCKET x 3

and72-PinSIMMSOCKETx2).

Supports512KB/1024KB(Optional)L2 Cache.

Supports three 16 bit ISA slots ,four 32 bit PCI slots and an AGP slot and

provides two independent high performance PCI IDE interfaces capable of

supporting PIO Mode 3/4 and Ultra-DMA33 devices.

Supports ATAPI (e.g. CD-ROM) devices on both IDE interfaces.

Supports a floppy port, a parallel port (EPP,ECP port), two serial ports

(16550 Fast UART compatible), 2 USB Ports, a PS/2 style mouse connecter

and a PS/2 style keyboard connector.

Supports Award Plug & Play BIOS.

Supports CPU Hardware sleep, APM (Advanced Power Management) and

ACPI (Advanced Configuration Power Interface).

Supports an ATX power supply connector for a Remote On/Off , a Phone-

Ring Power On and a Keyboard Power On Function.

Supports Switching Regulator for CPU power supply. and single jumper for

CPU working voltage selection.

Supports ESDJ (Easy Setting Dual Jumper) function for CPU selection.

Support hardware monitor function.

MVP3E

Figure2-1

ATX Power Conn.

Winboand

83877F

DIMM3

DIMM2

PCI#2

PCI#3

PCI#4

PCI#1

BIOS

SPEAKER TB-LEDRESET KEYLOCK

MVP3E Layout

FDD CONN.

Secondary IDE

IR CONN

JP3

BANK2

SIMM 1

SIMM 2

586B

598AT

SOCKET 7

Primary IDE

FDD1

64K*64

SRAM

COM1 PS/2

MOUSE

K/B

PRINTER PORT

COM2 USB

PORT

123

DIMM1

JP2

BANK1

BANK0

BANK2

HD-LED

Power-ON

64K*64

SRAM

AGP

Bus ClockMultiplier

+ +

<=======

1 51 5

JP5

JP4

(Optional)

Hardware Design

JP2 : CPUVcore voltage selection: ForPentiumProcessor withMMX technology,

AMD K6 and Cyrix 6x86L/6x86MX/M II

6-12:3.2VforAMDK6-PR2-233MHz

5-11:2.9VforAMDK6-PR2-166/200MHzandCyrix6x86MX/MII

4-10:2.8VforPentiumMMXand Cyrix 6x86L

3-9:2.4V Reserved

2-8:2.2V for AMD K63D CPUs

1-7:2.1V Reserved

612

JP3 Pentium / MMX JP3Cyrix /IBM

AMDK5/K66x86L

idt -C6 MultiplierBus CLOCK6x86MX

25 26

2-2Connectors andJumpers

This section describes the connectors and jumpers equipped in the motherboard.

Please refer to Figure 2-1 for the location of each connector and jumper.

1 2

4.5X

3.5X

2.5X

100MHz

83MHz

75MHz

66MHz

60MHz

Multiplier

Bus CLOCK

2 x

2.5 x

3 x

3.5 x

4 x

133MHz 66MHz L/MX-PR166

150MHz 75MHz L/MX-PR200

150MHz 60MHz MX-PR166

166MHz 66MHz MX-PR200

188MHz 75MHz M II/MX-PR233

210MHz 83MHz M II/MX-PR266

250MHz 100MHz M II/MX-PR333

180MHz 60MHz

200MHz 66MHz M II/MX-PR233

225MHz 75MHz M II/MX-PR300

250MHz 83MHz M II/MX-PR333

300MHz 100MHz M II/MX-PR350

233MHz 66MHz M II/MX-PR300

263MHz 75MHz M II/MX-PR333

290MHz 83MHz M II/MX-PR350

350MHz 100MHz

240MHz 60MHz

266MHz 66MHz M II/MX-PR333

300MHz 75MHz M II/MX-PR350

333MHz 83MHz

400MHz 100MHz

MVP3E

IrDA/ASK IR CONNECTOR

1.Power LED(+)

2.N/C

3.GND

4.Key-Lock

1.Speaker

2.N/C

3.GND

4.VCC

Reset Switch - Closed to restart system.

Speaker - connect to the system's speaker for beeping.

KeyLock - Keyboard lock switch & Power LED connector.

Turbo LED indicator - LED ON when higher speed is selected.

IDELEDindicator- LED ON when harddisks activate.

# There is no deturbo function so that the turbo LED is always ON.

5.GND

1.VCC

2.NC

3.IRRX

4.GND

5.IRTX

Power-ON - Push the button to turn on the system.

- Pressing less than 4 seconds to enter the suspend mode

- Pressing more than 4 seconds to turn off the system

CPU FAN Connector

CHASSIS FAN Connector

WOL(Wake-up On LAN) Connector

Hardware Design

2-3System MemoryConfiguration

This motherboardsupports different type of settings for the system memory. The

following figures and table provides all possible memory combinations.

DIMM2

32MB x1

16MB MAX.=384MB

8MB

BANK 0

BANK 2

128MB

DIMM3

BANK 1

DIMM1

64MB 32MB x1

16MB

8MB

128MB

64MB

32MB x1

16MB

8MB

128MB

64MB

DIMM 1 DIMM 2 DIMM 3 or SIMM1&2 TOTAL

BANK 0 BAMK 1 BANK 2 MEMORY

This motherboardsupports 2 kinds of powerful and flexible SDRAM frequency

selections. These can be synchronous with CPU bus clock or fixed as 66MHz. By

implementing the VCS (Virtual Clock Synchronization) technology, this motherboard

refers to the use of delay-lock-loop (DLL) to enable synchronous and pseudo-

synchronous operation of the processor and DRAM, AGP and PCI buses. The JP5

allows user to set the SDRAM Frequency between 66/100MHz.

JP5 SDRAM Clock Selection

1-2 : Fixed as 66MHz

2-3 : SDRAM Clock = CPU Bus Clcok

Jumper'sposition:

1-2 : Pseudo-synchronous Status(Fixed as 66MHz)

A more stable and compatible operation condition for non-100MHz based SDRAM

when you are using 100MHz based CPU. This setting is suitable for those users who

are like to remain the usage of current SDRAM module.

2-3 : Synchronous Status(SDRAM Clock= CPU Bus Clock)

Increasing the bus speeds from the traditional 66MHz to 100MHz greatly improves

system performance because the speed at which data traveling between the CPU and

memory is increased by 50%. However, there is one thing you should bear in mind.

Please make sure you are using 125MHz(-8) based or above SDRAM module.

BANK 2

SIMM1

SIMM2

16MB x2

8MB

32MB

Hardware Design

2-5 External Modem Ring-in Power ON and Keyboard Power ON

Functions

On the basis of bounded functions in I/O chipset, the two serial ports are able to

support the External Modem Ring-in Power ON function. Once users connect the

external modem to COM1 or COM2, this motherboard allows users to turn

on their system through the remote and host's dial-up control.

ExclusiveKeyboardPowerONFunction

To innovate a unique feature to benefit users, we devoted ourselves to create the

easiest and most convenient way to turn on your system based on the ATX

power supply. This function is available only under system being connected to

ATX power supply.

How to work with it

Step 1: Please place JP4 at the position 2-3 after you finished the system installation.

Step 2 : Push the momentary switch to turn on your system and then push again to

hold for more than 4 seconds to turn it off as soon as you turn it on.

Step 3:You can enjoy the Keyboard Power ON function by pressing any 1 or 2

keys on you keyboard at the same timefor 1-2 seconds. Your system will be

turned on automatically, after releasing the keys. To power off you system,

you can use the Soft-OFF function under Windows 95.

Notes:

1. The number of keys needed to turn on a system depends on the model of

keyboard you are applying due to different loadings on different keyboards.

Here, we would like to suggest you push 2 keys at the same time..

2.Intel ATX version 2.0 specification has recommended you use the power

supplywith0.72A(720mA). WithourEP-51MVP3E-Mmotherboard,

the 5.0VSB

standby power only has to be > = 0.1A (100mA) then you can enjoy this

unique benefit. However, the ATX power supply which is < 0.1 (100mA) is still

applicable to your system by placed JP4 at the position 1-2 to disable this

feature.

JP4 Keyboard Power-ON Function Selection

1-2 : Disabled

2-3 : Enabled

Indice

Altri manuali EPOX Scheda madre

Manuali Scheda madre popolari di altre marche

DFI

DFI SD170 Manuale utente

ASROCK

ASROCK ROMED8-2T Manuale utente

Asus

Asus P2L97A Manuale utente

Winmate

Winmate IC70 Manuale utente

Asus

Asus MES-B Manuale utente

Grantech

Grantech SYS8F377VGGA-3OMN Manuale utente

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuale utente

Gigabyte

Gigabyte GA-9IVDT Manuale utente

Texas Instruments

Texas Instruments ADS8372EVM Manuale utente

Commell

Commell MS-C73 Manuale utente

IBT Technologies

IBT Technologies MB860 Manuale utente

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuale utente

Biostar

Biostar M7VIT Bravo Istruzioni per l'uso e l'installazione

Intel

Intel D33217CK Manuale utente

Asus

Asus F1A55-M LX PLUS R2.0 Manuale utente

EPC

EPC EPC9147C Manuale utente

Asus

Asus EX-B760M-V5 D4 Manuale utente

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Manuale utente