ETC Source Four PARNel Manuale utente

Product information and specifications subject to change.

Part Number:

7061M1250-06.01

Rev B

Released: June 2008

Picking# 7061M1008-D

User Manual

Production Dates: September 2004 - Present

i Table of Contents

Table of Contents

ETC

, Emphasis

, Expression

, Insight™, Imagine™, Focus™, Express™, Unison

, Obsession

II, ETCNet2™,

EDMX™, Source Four

, Revolution

, Sensor

, and WYSILink™ are either registered trademarks or trademarks

of Electronic Theatre Controls, Inc. in the United States and other countries.

All other trademarks, both marked and not marked, are the propertyof their respective owners.

ETC intends this document, whether printed or electronic, to be provided in its entirety.

Basic Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Fixture information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Color frame holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Replacing the HPL lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Focus knob positioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Lens identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Changing front lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Cleaning glass lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Cleaning the reflector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Basic Assembly 1

Basic Assembly

WARNING:

Please note the following safety warnings before use:

Do not mount the fixture on or near combustible surfaces.

Do not operate the fixture without a lens installed.

Always hang the fixture with the color frame retaining clip in the locked

position.

Figure 1

Yoke locking knob

Clear lens

Lamp housing

Yoke

Lens rotating ring

Color frame holder

Color frame

Lens catcher

Gel retaining clip

Tabs

Stippled lens

Focus knob

2Source Four PARNel User Manual

Fixture information

HPL lamp table

Color frame holder

The color frame holder is equipped with a spring-loaded retaining clip that prevents color frames

and accessories from falling out. See Figure 2.

Step 1: Release the retaining clip by pushing it sideways while gently pulling backwards.

Step 2: Insert the color frame.

CAUTION:

Do not use lamps other than the HPL in Source Four fixtures. Use of lamps other

than HPL will void UL/cUL safety compliance and your warranty.

Lamp code Watts Volts Initial Lumen Color temp. Average rated life

HPL 780/77* 750 77 22,950 3,250° 300 hours

HPL 550/77* 550 77 16,170 3,250° 300 hours

HPL 550/77X* 550 77 12,160 3,050° 2000 hours

HPL 750/115 750 115 21,900 3,250°K 300 hours

HPL 750/115X 750 115 16,400 3,050° 1500 hours

HPL 575/115 575 115 16,520 3,250°K 300 hours

HPL 575/115X 575 115 12,360 3,050°K 2000 hours

HPL 375/115 375 115 10,540 3,250°K 300 hours

HPL 375/115X 375 115 8,000 3,050°K 1000 hours

HPL 750/120 750 120 21,900 3,250°K 300 hours

HPL 750/120X 750 130 16,400 3,0500°K 1500 hours

HPL 575/120 575 120 16,520 3,250°K 300 hours

HPL 575/120X 575 120 12,360 3,050°K 2000 hours

HPL 750/230 750 230 19,750 3,200°K 300 hours

HPL 750/230X 750 230 15,600 3,050°K 1500 hours

HPL 575/230 575 230 14,900 3,200°K 400 hours

HPL 575/230X 575 230 11,780 3,050°K 1500 hours

HPL 375/230X 375 230 7,250 3,000°K 1000 hours

HPL 750/240 750 240 19,750 3,200°K 300 hours

HPL 750/240X 750 240 15,600 3,050°K 1500 hours

HPL 575/240 575 240 14,900 3,050°K 400 hours

HPL 575/240X 575 240 11,780 3,050°K 1500 hours

HPL 375/240X 375 240 7,250 3,000°K 1000 hours

* To be used with ETC Dimmer Doubler™

WARNING:

Make sure all color frame accessories are locked in position with the

retaining clip before hanging the fixture.

Figure 2

Retaining clip in the

locked position

Basic Assembly 3

Step 3: Lock the retaining clip by pushing sideways while gently pushing forward.

Replacing the HPL lamp

A lamp must be installed before you use the fixture.

Step 1: Disconnect power to the fixture before installing the lamp.

Step 2: Loosen the knurled bolt on the back of the lamp housing and pull the housing out.

Step 3: Holding by the base, remove the HPL lamp from its box.

Note:

Use only color frames or accessories with 7.5 inch mounting flange.

Note:

The performance of saturated colors may be less than desirable in any theatrical

lighting fixture, especially when equipped with a 750w lamp. For best results,

always use high-quality color media rated for high-temperature use.

ETC’s optional Gel Extender, part # PSF1029, will provide maximum color media

life. The use of any gel extender accessory may limit the coverage of any wide-

angle lens or beam setting.

A variety of heat shield products is also available from many color media

manufacturers. Follow the manufacturer’s instructions for the use of these

products.

Note:

Verify that the HPL lamp you intend to install is suitable for your facility’s voltage;

115-, 120-, 230-, and 240-volt HPL lamps are available.

See HPL lamp table, page 2. Operating HPL lamps above their rated voltage

reduces lamp life and can cause premature lamp failure.

WARNING:

Unplug the fixture and allow it to cool down before attempting to change the

lamp.

CAUTION:

Use caution when installing or replacing any lamp.

When installing/replacing lamp, be sure to point the lamp away from your face and

away from others before inserting it firmly into the assembly.

This may prevent injuries if the lamp should break.

HPL lamp

Lamp retention

brackets

Lamp housing Figure 3

Knurled bolt

INCORRECT CORRECT

4Source Four PARNel User Manual

Step 4: Align the flat sides of the lamp base with the retention brackets on either side of the

socket as shown in Figure 3.

Step 5: Push down on the lamp base until the lamp seats firmly. When properly installed, the top

of the lamp’s base will be even with the top edges of the retention brackets.

Step 6: Press lamp retaining clip across lamp base to secure.

Step 7: Reinstall the lamp housing by aligning the bolt hole and tightening the knurled bolt.

Focus knob positioning

To adjust focus knob tension, loosen or tighten the focus knob screw. See Figure 4.

Lens identification

Lenses for the Source Four PARNel come in two versions. The wave/clear lens is in a fixed position

in the rear of the fixture. The wave/stippled lens is in the rotating ring at the front of the fixture. The

wave surfaces face each other.

Note:

To avoid premature lamp failure, do not touch the lamp glass. If you do, clean it

carefully with isopropyl alcohol and a clean lint-free cloth. Allow to dry before

operation.

CAUTION:

Improperly installed lamps cause premature lamp failure and socket problems.

CAUTION:

Lens rotation knob does not rotate 360°. Do not attempt to exceed limit.

Focus knob in

flood position

Figure 4

Focus knob in

spot position

45° field angle

25° field angle

Focus knob

screw

Figure 5

Wave/Stippled Lens (WS) Wave/Clear Lens (WC)

Basic Assembly 5

Changing front lens

Replace lens if it becomes cracked or badly scratched.

Removing a wave/stippled front lens

Step 1: Place the fixture on a flat, stable work surface. Do Not remove or install lenses with fixture

hanging.

Step 2: Rotate the focus knob to the full spot position.

Step 3: Tilt the front of the fixture down at least 45°. See Figure 6.

Step 4: Press the spring clip with your finger to release the lens.

Step 5: Allow the lens to drop forward from under the clip.

Step 6: When the lens drops, remove your finger, allowing the lens to slide forward until it rests

on the lens catchers. See Figure 7.

Step 7: Carefully remove the lens.

Installing a wave/stippled front lens

Step 1: Position the fixture with the front of the unit (lens side) facing you, and tilted slightly

upward. See Figure 8.

Step 2: Rotate the focus knob to the full spot position.

Step 3: Hold the lens by the edge and position it so the convex side faces the rear of the fixture.

Step 4: From the top of the fixture, slide the lens behind the lens catchers and position it behind

the tabs on the bottom of the lens rotator ring.

Step 5: Gently push the top of the lens inward until it snaps behind the spring clip.

CAUTION:

Never operate the fixture without a lens in place.

WARNING:

Unplug the fixture and allow it to cool down before attempting to change a

lens.

Note:

Installing the front lens with the contoured side out will not impair the optics, but it

will make removing the lens difficult.

Spring clip

Lens

Focus knob

Retaining clip

Tab Lens catcher

Retaining clip

Spring clip

Figure 6 Figure 7 Figure 8

6Source Four PARNel User Manual

Positioning the wave/stippled front lens.

Step 1: There are seven notches cut into the stippled side of the lens. Position the lens

so the cluster of three notches is on top. The center notch of the cluster aligns

with the spring clip on the lens retainer ring. See Figure 9.

Step 2: The bottom of the lens has a cluster of four notches. Place the two center notches

behind the tabs at the bottom of the lens rotator ring.

Cleaning glass lens

Replace lenses if they contain visible damage (cracks or deep scratches) that may impair their

effectiveness.

Remove dust with a blast of oil-free air or wipe with a clean, lint-free cloth. Isopropyl alcohol, distilled

water or a 50%-50% mixture of each can be used to clean the glass surface.

Cleaning the reflector

The reflector is located behind the rear, fixed position wave/clear lens and requires disassembly of

the fixture to access it. See the Source Four ParNel Assembly Guide for instructions on fixture

disassembly/assembly.

WARNING:

Do not use ammonia-based or other harsh commercial cleaners. Clean lens

only as directed.

Commercially available glass cleaning agents should be avoided as they

may contain ammonia, other harsh chemical detergents or abrasive agents.

These cleaners may damage the glass surface and the Anti-Reflective

coatings. Do not immerse or soak the glass in any cleaning solution.

Top center notch

Bottom two center notches

Figure 9

Basic Assembly 7

8Source Four PARNel User Manual

Altri manuali per Source Four PARNel

Indice

Altri manuali ETC Attrezzatura per DJ

ETC

ETC Source Four PAR EA Manuale utente

ETC

ETC Irideon FPZ Manuale utente

ETC

ETC Congo jr Master Playback Wing Manuale utente

ETC

ETC CE Source Four Guida alla configurazione

ETC

ETC ColorSource Linear Manuale utente

ETC

ETC Desire series Manuale utente

ETC

ETC Source 4WRD Manuale utente

ETC

ETC ColorSource CYC Manuale utente

ETC

ETC Source Four XT HID Zoom Manuale utente

ETC

ETC ColorSource Linear Manuale utente

ETC

ETC High End Systems SolaWash 1000 Manuale utente

ETC

ETC ColorSource Manuale utente

ETC

ETC Source Four LED S4LEDLS Manuale utente

ETC

ETC ColorSource PAR Manuale utente

ETC

ETC Source Four Mini LED Manuale utente

ETC

ETC ColorSource Spot Manuale utente

ETC

ETC Source Four Zoom CE Manuale utente

ETC

ETC High End Systems SHOWGUN Manuale

ETC

ETC Source 4WRD II Manuale utente

ETC

ETC Source Four LED Series Manuale utente

ETC

ETC Irideon WLZ Manuale utente

ETC

ETC Source Four LED Series Manuale utente

ETC

ETC Source Four Manuale utente

ETC

ETC Source Four LED Series Manuale utente

Manuali Attrezzatura per DJ popolari di altre marche

ALPHA LITE

ALPHA LITE ALPHA 1500 Manuale del proprietario

Chauvet

Chauvet OVATION E-930VW Manuale utente

Zumtobel

Zumtobel APHRODITE Home Manuale utente

Snow Masters

Snow Masters Zig Oscillator Manuale utente

EuroLite

EuroLite 50530554 Manuale utente

Beamz

Beamz BUV243 Manuale utente

thomann

thomann Stairville DJ Lase 40-G MK-III Manuale utente

Eagletone

Eagletone 6 Eyes Flower Manuale utente

EuroLite

EuroLite FLD-1508 Manuale utente

Technical Pro

Technical Pro LG8xSEA Manuale utente

JB Systems

JB Systems Lounge Laser DMX Manuale utente

Lightmaxx

Lightmaxx Vega Halo 90 Manuale utente

Elation

Elation FUZE WASH Z350 Manuale utente

Maverick

Maverick MK3 WASH Manuale utente

Infinity

Infinity TF-260C7 Fresnel Manuale utente

Chauvet

Chauvet EVE E-50Z Manuale utente

Eliminator Lighting

Eliminator Lighting E 138 Manuale utente

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manuale utente