ETC Source 4WRD II Manuale utente

ETC Quick Guide

Source 4WRD II Version 1.1.2

Corporate He adqua rte rs Middleton, WI, USA +1 608 831 4116

London, UK +44 (0)20 8896 1000 Holzk irchen, DE +49 (80 24) 47 00-0

Rome , IT +39 (06) 32 111 683 Hong Kong +852 2799 1220 P aris, FR +33 1 4243 3535

Web etcconnect.com Support support.etcconnect.com

Product information and specifications subject to change. ETC intends this document

to be provided in its entirety. Trademark and patent info:etcconnect.com/ip

7067M1330-1.1.2 Rev A Released 2020-10

Introduction

The Source 4WRDII LED is a replacement for a standard Source Four burner

assembly. It converts the HPL source to a white-light LED and provides a

significant reduction in power consumption.

For complete information, download the Installation and User

Manual at etcconnect.com, or view online help on your

smartphone or tablet by scanning this code.

What's in the Box

•

Source 4WRD II retrofit

•

Threaded post (see

Install the Source 4WRD II Retrofit on page4

)

Safety

The Source 4WRD II fixture is intended for professional use only. Read the

entire manual before using this equipment.

WARNING: Note the following safety warnings before use:

•

Do not mount the fixture on or near a flammable surface.

•

Do not use this fixture with a damaged power lead. If the

power lead (cord set) is damaged, it must be replaced.

•

Mount and support the fixture only by the primary

suspension holes in the yoke.

•

Suspend the fixture from a suitable structure using only

hardware rated for the weight of the fixture.

•

In addition to primary suspension, attach a safety cable

(ETC Model 400SC or other approved safety cable or

device) to the fixture housing. An appropriate attachment

point (hole) is provided in the protruding tab on the fixture

housing.

•

Disconnect the unit from power and DMX and allow the

fixture to cool before removing or installing accessories,

and before all cleaning and maintenance.

ETC Quick Guide

Source 4WRD II Version 1.1.2

AVERTISSEMENT : Prendre connaissance des avertissements

de sécurité suivants avant toute utilisation :

•

Ne pas installer le projecteur sur ou à côté d’une surface

inflammable.

•

Ne pas utiliser ce projecteur avec un cordon d’alimentation

endommagé. Si le cordon d’alimentation (câble) est abîmé,

il doit être remplacé.

•

Installer et accrocher le projecteur uniquement par les

trous de fixation principaux de la lyre.

•

Accrocher le projecteur à une structure convenable en

utilisant seulement du matériel adapté au poids du

projecteur.

•

En plus de l'accroche principale, fixer une élingue de

sécurité (modèle ETC400SC ou autre câble/dispositif de

sécurité certifié) au corps du projecteur. Un point

d’accroche (trou) approprié est prévu dans la patte qui

ressort du boîtier du projecteur.

•

Déconnecter l’alimentation et le DMX et laisser le

projecteur refroidir avant d’enlever ou installer l'optique

découpe ou les autres adaptateurs, et avant tout

nettoyage et entretien.

WARNING: Note the following safety warnings before use:

•

The Source 4WRD II LED is not user serviceable. Field

modification of the Source 4WRD II LED will void your ETC

warranty.

•

Do not use the fixture below 5°C (41°F).

•

Minimum storage temperature is 5°C (41°F). When the

fixture has been stored or transported in cold

temperatures, allow it to warm to room temperature for

a minimum of 1hour before applying power. Applying

power to a cold fixture will cause damage to the fixture

and void the ETCwarranty.

•

Do not use this fixture if a glass lens is deeply scratched or

cracked. Damaged lenses must be replaced.

•

To prevent wiring damage, or abrasion, do not expose

wiring to edges of sheet metal or other sharp objects.

•

Use the fixture in dry locations only, where humidity does

not exceed 90 percent (non-condensing). These fixtures

are not intended for outdoor use.

Source 4WRD II Page 2 of 8 ETC

ETC Quick Guide

Source 4WRD II Version 1.1.2

Retrofit the Fixture

WARNING: RISK OF FIRE OR ELECTRIC SHOCK! Installing the

Source 4WRDII LED retrofit kit requires knowledge of luminaire

electrical systems. If you are not qualified, do not attempt

installation. Contact a qualified electrician.

AVERTISSEMENT : RISQUE D'INCENDIE OU DE DÉCHARGE

ÉLECTRIQUE! Installer le nécessaire de conversion Source 4WRDII

LED nécessite une connaissance des systèmes électriques de

projecteurs. Si vous n’êtes pas qualifié, ne tentez pas

l’installation. Faire appel à un électricien qualifié.

Note:

THE RETROFIT KIT IS ACCEPTABLE AS A COMPONENT OF A

LUMINAIRE WHERE THE SUITABILITY OF THE COMBINATION SHALL BE

DETERMINED BY AUTHORITIES HAVING JURISDICTION.

Wire the Power Connector(If Needed)

If you ordered a Source 4WRD II retrofit without a power connector, wire the

connector in accordance with all national and local electrical codes:

•

Brown = Live

•

Blue = Neutral

•

Green/Yellow = Protective earth

Remove Incandescent Lamp Housing

1. Unplug the Source Four incandescent fixture and place it on a flat,

stable surface.

2. Loosen the brass thumb screw located above the beam adjustment

knob. The lamp housing is now loose.

3. Remove the lamp housing from the fixture body.

Source 4WRD II Page 3 of 8 ETC

ETC Quick Guide

Source 4WRD II Version 1.1.2

Install the Source 4WRD II Retrofit

WARNING: RISK OF FIRE OR ELECTRIC SHOCK! Install this kit only

onto luminaires that have the construction features and

dimensions shown in the images in this document and where the

input rating of the retrofit kit does not exceed the input rating

of the luminaire.

AVERTISSEMENT : RISQUE D'INCENDIE OU DE DÉCHARGE

ÉLECTRIQUE! N’installer ce kit que sur les projecteurs qui ont les

caractéristiques de construction et les dimensions indiquées sur

les images de ce document et où la puissance électrique

nécessaire à la conversion n’excède pas la puissance maximale du

projecteur.

WARNING: Do not make or alter any open holes in an enclosure

of wiring or electrical components during kit installation.

CAUTION:

Do not touch or clean LED emitters with anything

other than oil-free canned air.

Tools required:

•

Adjustable wrench

•

#2 Phillips screwdriver

1. Use oil-free canned air to clean the LED emitters before you install the

retrofit. Do not touch the LEDemitters.

2. With the fixture resting securely on a flat surface, attach the supplied

threaded post to the back end of the fixture body. Use an adjustable

wrench to tighten the threaded post one-quarter turn past finger

tight.

3. Gently slide the Source 4WRDII LED onto the fixture body and

threaded post while guiding the LED tower into the lamp housing

hole, as shown in the following image. Take care to prevent contact

between the LEDs and the reflector.

Source 4WRD II Page 4 of 8 ETC

ETC Quick Guide

Source 4WRD II Version 1.1.2

Insert threaded

post here

Tighten

screw

Z-adjustment

knob

Source Four

fixture body

Lamp

housing

hole

4. Use a #2 Phillips screwdriver to tighten the screw located on the back

end of the Source 4WRDII LED, directly above the Z-adjustment knob.

5. Pull gently to verify secure attachment.

6. Set the Z-adjustment using the Z-adjustment knob. See

Set the Z-

adjustment on page8

Attach C-clamp and Safety Cable

The C-clamp attaches the fixture to the mounting pipe and allows you to

adjust the position of the mounted fixture. ETC recommends using 1.5in

schedule 40 pipe.

1. Tightly fasten the C-clamp to the yoke with the provided yoke bolt and

lock washer.

2. Place the C-clamp on mounting pipe, and then tighten the pipe bolt to

secure it.

3. Loosen the C-clamp pan screw and rotate the yoke to the desired

position.

4. Tighten the pan screw to lock the fixture.

5. Connect the safety cable.

6. Tighten the C-clamp pipe bolt to 15–20 ft-lb (20–27 Nm),

approximately finger tight plus up to one-quarter turn.

CAUTION:

Do not exceed 25 ft-lb (33 Nm) while tightening the

C-clamp pipe bolt. Do not use excessive force.

7. Tighten the yoke pivot bolt to 5–10 ft-lb (6–7 Nm), approximately

finger tight plus up to one-eighth turn.

CAUTION:

Do not exceed 15 ft-lb (20 Nm) while tightening the

yoke pivot bolt. Do not use excessive force.

Source 4WRD II Page 5 of 8 ETC

ETC Quick Guide

Source 4WRD II Version 1.1.2

Connect Cables

You can control the fixture using AC power or DMX. Configure the fixture to

use the appropriate control method on the user interface. See

Configure the

Fixture on the facing page

WARNING: Do not use or store the Source 4WRD II fixture

below 5°C (41°F). When the fixture has been stored or

transported in cold temperatures, allow it to warm to room

temperature for a minimum of 1 hour before applying power.

Applying power to a cold fixture will cause damage to the fixture

and void ETC warranty.

Note:

For optimum performance, make sure that your dimmer is out

of regulated mode. See Line-dimming on the facing page for

recommended dimmer settings.

Note:

Connecting both power and data from a SmartBar 1 to a

Source 4WRD II fixture may cause flickering.

1. If you are using DMX control: Connect one RJ45 data cable for data-in

and one for data-thru, as needed. Use the strain relief at the bottom of

the fixture to support the data cables.

•

To order an RJ45-to-female XLR adapter, use ETC part number

W6538.

•

To order an RJ45-to-male XLR adapter, use ETC part number

W6539.

2. If you are using DMXcontrol and this is the last fixture in the line,

terminate the fixture with a 120Ohm resistor. Please contact your ETC

customer service representative to purchase ETC part number N4086.

3. Connect the fixture to the power source.

Source 4WRD II Page 6 of 8 ETC

ETC Quick Guide

Source 4WRD II Version 1.1.2

DMXDimming

When dimming via DMX, consider the following:

•

When using DMX over Cat5, use Cat5e or better.

•

Cable distance for full DMX daisy chain must not exceed 300m

(1000ft).

•

Up to 32 fixtures can be connected together into a daisy chain.

•

The fixture cannot be controlled via Ethernet protocols and should not

be directly connected to an Ethernet system.

•

When DMX data is lost, the LEDemitters turn off.

•

The fixture uses a single DMXchannel for intensity control.

Line-dimming

For the most current information on additional dimmer performance testing

for both ETC and non-ETC dimmers, please visit the ETC website:

https://support.etcconnect.com/ETC/Fixtures/Source_Four/Source_

4WRD%2F%2FSource_4WRD_PAR/Dimmer_Settings_for_Use_with_Source_

4WRD

Configure the Fixture

Up and down

navigation buttons

User interface

The two-button, seven-segment display

shows the DMXaddress, ACmode, or

the manually-set level. Use the up and

down navigation buttons to configure

the fixture.

•

Set a DMX address: Use the up

and down arrows to navigate to

thedesired DMX address number

(1–512).

•

Set the fixture to use line-

dimming (ACmode): Use the

down arrow to navigate one number

below DMX address 1. The display will read AC.

•

Manually set a level: Use the down arrow to navigate one number

below AC. The display will read L.FL (Level = Full). Usethe down arrow

to decrease the level to a percentage of full (L.99 = 99%, L.98 =

98%, etc.). You can set levels from 0%–100% (full).

Source 4WRD II Page 7 of 8 ETC

ETC Quick Guide

Source 4WRD II Version 1.1.2

Focus the Fixture

Set the Z-adjustment

Use the Z-adjustment knob located on the rear of the fixture to adjust the

field of the LED light for specific applications.

1. Turn on the fixture and aim it at a flat surface.

2. Slide the fixture barrel toward or away from the Source 4WRDII LED to

create a hard-edged beam of light.

3. Turn the knob toward PEAK or FLAT until you achieve the desired field.

Ideal beam of

uniform light

Adjust toward PEAK to

blend overlapped beams

Adjust toward FLAT to

improve sharp focus

Z-adjustment knob

Note:

The Source 4WRD PAR or PARNel Fixture Body optics are

optimized for PEAKfocus. When using the Source 4WRDII LED in a

Source 4WRD PAR or PARNel Fixture Body, turn the Z-adjustment

knob toward PEAK until the knob becomes loose, and then tighten

the Z-adjustment knob an additional quarter turn. This sets the LED

light source into the appropriate position within the fixture.

Source 4WRD II Page 8 of 8 ETC

Altri manuali per Source 4WRD II

Indice

Altri manuali ETC Attrezzatura per DJ

ETC

ETC Source Four LED S4LEDLS Manuale utente

ETC

ETC Source Four XT HID Zoom Grid Louver Manuale utente

ETC

ETC Desire XTI Series Manuale utente

ETC

ETC High End Systems SolaPix 19 Manuale utente

ETC

ETC RoadHog 4 Manuale utente

ETC

ETC Source Four LED Series Manuale utente

ETC

ETC ColorSource Linear Manuale utente

ETC

ETC Desire series Manuale utente

ETC

ETC High End Systems SolaWash 1000 Manuale utente

ETC

ETC ColorSource PAR v1.7 Manuale utente

ETC

ETC Source Four Manuale utente

ETC

ETC CE Source Four Guida alla configurazione

ETC

ETC Prodigy FlyPipe Studio Manuale utente

ETC

ETC Desire series Guida alla configurazione

ETC

ETC Ion Classic Manuale utente

ETC

ETC Source Four jr Manuale utente

ETC

ETC Source Four Mini LED Manuale utente

ETC

ETC Source Four PAR Manuale utente

ETC

ETC Source Four LED Series Manuale utente

ETC

ETC Desire D22 Manuale utente

ETC

ETC ColorSource PAR Manuale utente

ETC

ETC ColorSource Fresnel V Manuale utente

ETC

ETC IRIDEON AR500 Manuale utente

ETC

ETC ColorSource Manuale utente

Manuali Attrezzatura per DJ popolari di altre marche

ALPHA LITE

ALPHA LITE ALPHA 1500 Manuale del proprietario

Chauvet

Chauvet OVATION E-930VW Manuale utente

Zumtobel

Zumtobel APHRODITE Home Manuale utente

Snow Masters

Snow Masters Zig Oscillator Manuale utente

EuroLite

EuroLite 50530554 Manuale utente

Beamz

Beamz BUV243 Manuale utente

thomann

thomann Stairville DJ Lase 40-G MK-III Manuale utente

Eagletone

Eagletone 6 Eyes Flower Manuale utente

EuroLite

EuroLite FLD-1508 Manuale utente

Technical Pro

Technical Pro LG8xSEA Manuale utente

JB Systems

JB Systems Lounge Laser DMX Manuale utente

Lightmaxx

Lightmaxx Vega Halo 90 Manuale utente

Elation

Elation FUZE WASH Z350 Manuale utente

Maverick

Maverick MK3 WASH Manuale utente

Infinity

Infinity TF-260C7 Fresnel Manuale utente

Chauvet

Chauvet EVE E-50Z Manuale utente

Eliminator Lighting

Eliminator Lighting E 138 Manuale utente

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manuale utente