ETC ColorSource Linear Manuale utente

ETC Installation Guide

ColorSource®Linear v1.7

Corporate Headquarters



Middleton, Wisconsin, USA



Tel +608 831 4116

Service (Americas)



[email protected]

London, UK



Tel +44 (0)20 8896 1000



Service: (UK) [email protected]

Rome, IT



Tel +39 (06) 32 111 683



Service: (UK) [email protected]

Holzkirchen, DE



Tel +49 (80 24) 47 00-0



Service: (DE) [email protected]

Hong Kong



Tel +852 2799 1220



Service: (Asia) [email protected]

Web: etcconnect.com



Product information and

specifications subject to change.



ETC intends this document to be provided in its entirety.



US Patents

8,384,294 . 8,403,523 . 8,593,074 . 8,633,649 . 8,723,450 . 8,878,455 . 9,041,308



EU Patents 2638781 . 6020110157302



All other patents pending.

7414M2100-1.7



Rev A



Released 2018-04

Overview

The ColorSource Linear is an affordable LED fixture that uses the RGB-L (red,

green, blue, and lime) color system to provide a rich, bright light.

The fixture is available in three lengths:

• ColorSource Linear 1 (0.5 meter)

• ColorSource Linear 2 (1 meter)

• ColorSource Linear 4 (2 meter)

The ColorSource Linear is available in both original and Deep Blue variants.

The Deep Blue uses an array that offers richer, more saturated blues and

stronger magentas in exchange for the more jewel-toned blues like sky or

turquoise. For more information, see the ETC website at etcconnect.com.

Note:

Features described in this document require the latest

version of software. For information on updating fixture

software, see Updating the fixture software on page 14.

ColorSource Linear 1

ETC Installation Guide

ColorSource Linear v1.7

ColorSource Linear v1.7 Page 2 of 20 ETC

Safety

Read the entire manual before using this equipment.

Environment

The ColorSource Linear operates in ambient temperatures of 0°C–40°C and

comes with a variable-speed fan.

CAUTION:

• Risk of eye injury. Do not stare directly into the light.

• Do not operate in proximity to flammable materials.

WARNING:

Disconnect the fixture from power and DMX and allow

it to cool before performing any cleaning and

maintenance.

Note:

The ColorSource Linear is for indoor use only.

Note:

• Maximum recommended ambient operating

temperature: Ta = 40°C (104°F)

• Maximum anticipated external surface temperature

at 40°C ambient: Tmax = 80°C (176°F)

• External temperatures after 5 minutes of full-

brightness operation at 25°C (77°F) ambient:

36°C (97°F)

• External Temperature (steady state achieved) at

25°C (77°F): 48°C (118°F)

ETC Installation Guide

ColorSource Linear v1.7

ColorSource Linear v1.7 Page 3 of 20 ETC

Electrical

• Operates between 100V and 240VAC at a frequency of 50/60Hz.

• Maximum power consumption:

- Linear 1: 120W

- Linear 2: 240W

- Linear 4: 480W

• Up to 9 cells (0.5 m segments) may be linked via power thru connector.

• Up to 10 cells (0.5 m segments) total per circuit when used with an

R20 Relay Module or Unison Echo®Relay Panel. Consult breaker trip

curves when used with other equipment. Requires power from a non-

dimmable source.

• Inrush (Linear 1/Linear 2/Linear 4):

- 120V: 35A/35.6A/67.5A (first half-cycle)

- 240V: 49A/85.6A/153A (first half-cycle)

Typical power consumption

Linear 1 100V 120V 230V

Idle Power/Current

1.63W/0.03A 1.55W/0.03A 1.43W/0.03A

Direct at Full/Current

107W/1.07A 105W/0.88A 104W/0.46A

Linear 2 100V 120V 230V

Idle Power/Current

2.86W/0.06A 2.98W/0.06A 2.56W/0.06A

Direct at Full/Current

210.83W/2.12A 208.67W/1.75A 204.5W/.91A

Linear 4 100V 120V 230V

Idle Power/Current

5.28W/0.11A 5.24W/0.11A 4.65W/0.12A

Direct at Full/Current

424.17W/4.27A 419.33W/3.52A 409.17W/1.82A

ETC Installation Guide

ColorSource Linear v1.7

ColorSource Linear v1.7 Page 4 of 20 ETC

Accessories

You can use several half-meter optional accessories with ColorSource Linear

fixtures, including:

• Secondary lenses (horizontal, vertical, and round)

• Barn doors (7414K1020)

• Louver (7414K1019)

For information on installing secondary lenses, see

Installing secondary lenses

page 15

Accessories for Linear 2 and Linear 4

For the Linear 2 and Linear 4 fixtures, order one accessory for each 0.5 meter

segment (cell) of the fixture. For example, for a Linear 2 fixture, order two

barn door accessory kits to fit the full length of the fixture.

Spacers for secondary lenses are included with the fixture. Use these spacers

to hold the accessories in position when multiple lenses are used in the

Linear 2 and Linear 4 fixtures. The spacers are positioned between the

0.5 meter lenses.

Contact your local dealer for more information.

Installation

Mounting

The ColorSource Linear ships with a pair of floor trunnions for mounting.

You also have the option of using C-clamps with the trunnions to hang the

fixture. Attach the C-clamps to the holes in the trunnion feet (see figure on

page 5

The ColorSource Linear 1 has two additional mounting options. Contact your

local dealer for more information.

• Yoke with C-clamp (7414K1017)

• Double yoke with C-clamp for mounting two fixtures (7414K1018)

Note:

Ensure that the trunnions are installed with the feet

inward so that fixtures can be lined up end-to-end, if

needed.

ETC Installation Guide

ColorSource Linear v1.7

ColorSource Linear v1.7 Page 5 of 20 ETC

Safety cable

Two safety cable anchor points are

provided on the fixture housing.

The anchor points also include two

cutouts that can be used for cable

strain relief.

Connectors

•Power: Two powerCON®

connectors for power in and

thru

•Data (DMX512/RDM): Two

five-pin XLR connectors

two RJ45 connectors for data

in and thru

Conversion cables are available from ETC. Please contact your ETC customer

service representative and request part number W6538 for RJ45 to female

XLR or part number W6539 for RJ45 to male XLR.

Connector locations

•Linear 1: Power connectors on one side of the fixture and data

connectors on the other

•Linear 2 and Linear 4: Power and data connectors on each end (to

facilitate daisy-chaining)

Note:

This fixture is not Ethernet/data network compatible.

Note:

The ColorSource Linear is not self terminating. You must

terminate the last fixture in line with a 120 Ohm resistor.

XLR terminators are not available from ETC.

To purchase an RJ45 terminator, please contact ETC

customer service and request part number N4086.

Safety cable

anchor point

C-clamp

attachment

point

Cutout for

cable strain relief

ETC Installation Guide

ColorSource Linear v1.7

ColorSource Linear v1.7 Page 6 of 20 ETC

Setting up the fixture

See the fixture illustrations below and on the following page for reference.

1: Plug power cord into the powerCON In connector on the rear of the

fixture.

2: Make any power-thru cable connections prior to applying a power

source.

3: Make any DMX connections, and if the fixture is the last in a DMX line,

terminate the fixture. See

Connectors

page 5

4: Plug power cord into power source.

Data in

and thru

connectors

User interface

(display)

Power in

and thru

connectors

Mode button

Up and

Down

buttons

Trunnion

locking

knob

Trunnion

locking knob

Linear 1

Mode button

ETC Installation Guide

ColorSource Linear v1.7

ColorSource Linear v1.7 Page 7 of 20 ETC

Powering up

1: Press any button to wake the display. The display shows the DMX

address. See

Setting the DMX address

page 8

2: Press the Mode button to access the Presets/Sequences menu. See

Setting presets and sequences

page 12

Adjusting the tilt

The fixture can be tilted up and down as needed.

1: Loosen, but do not remove the two trunnion locking knobs.

2: Tilt the fixture to the desired angle.

3: Tighten the trunnion locking knobs.

User interface

The user interface allows you to set the start

address of the fixture, access the stand-alone

presets and sequences, set the DMX control

mode, and set the Grouping mode (Linear 2 and

Linear 4 fixtures only).

• After 5 seconds of inactivity when DMX is

present, the display goes dark.

• The DMX address will blink when no DMX

is present and a preset or sequence is not

active. The inactivity time-out is disabled

while in a data loss state.

Power and data

connectors are

paired on each

side to facilitate

daisy-chaining

Up and Down

buttons

User interface

(display)

Mode button

Grouping button

and LED indicators

Linear 2 and Linear 4

Linear 1

shown

ETC Installation Guide

ColorSource Linear v1.7

ColorSource Linear v1.7 Page 8 of 20 ETC

Mode button

Pressing the Mode button activates the Presets/Sequences menu; the last

active preset or sequence plays automatically. Pressing the Mode button a

second time deactivates the selected preset or sequence. The display will

revert to show the DMX start address.

• If DMX data is present, the current preset or sequence plays in the

background and DMX data continues to take priority.

• If DMX data is lost and a preset is active in the background, the last

selected preset or sequence automatically plays.

Setting the DMX address

1: Press any button to wake the display. The display shows the DMX

address.

2: Use the Up and Down buttons to select the DMX address for the

fixture.

You can also use RDM for DMX addressing. See

Using RDM

page 17

Changing the DMX control mode

You can set the DMX control mode for the fixture to one of four available

mode options.

1: Press any button to wake the display. The display shows the DMX

address.

2: Press and hold the Mode button for 3 seconds. The display shows the

current DMX control mode.

3: Press the Up and Down buttons to change the DMX control mode.

•: 5-channel mode (intensity, red, green, blue, and strobe). This

is the default mode.

•: Direct emitter control (intensity, red, green, blue, indigo,

lime, and strobe).

•: 1-channel mode controls the intensity of preset 1 (defaults to

3200K White).

•: RGB mode (red, green, and blue).

4: Press the Mode button to confirm your selection.

The display will automatically return to the DMX address after 10 seconds of

inactivity, and edits to the DMX control mode will not be saved. This cancels

unsaved changes.

ETC Installation Guide

ColorSource Linear v1.7

ColorSource Linear v1.7 Page 9 of 20 ETC

Setting the Grouping mode

The ColorSource Linear 2 and the

ColorSource Linear 4 fixtures have

two Grouping modes:

•Group: Entire array functions as

a single fixture.

•Cell: Each 0.5 m segment (or

“cell”) of the array functions as

a distinct fixture with a

separate DMX start address.

To set the Grouping mode, press the

Grouping button until the LED

indicator for the chosen mode

illuminates.

In Cell mode, each cell is assigned a DMX address based on the DMX address

of the fixture (see

Setting the DMX address

page 8

) and the current DMX

control mode (see

Changing the DMX control mode

page 8

). For example,

if you set the DMX address on the fixture to 100, set the DMX mode to

5-channel, and set the Grouping mode to Cell, the starting DMX address of

the first cell will be 100 and the starting DMX address of the second cell will

be 105.

DMX control channels

Linear 1 and Linear 2/Linear 4 in Group mode

*Original ColorSource Linear fixture uses blue in channel 4; Deep Blue fixture

uses indigo in channel 4.

**Use DMX values of 0 or 255 for no strobe. Use values of 1–254 to increase

the strobe rate from 1 per second up to 33 per second.

DMX

Channel



(5 Channel)



(Direct)



(1 Channel)



(RGB)

1 Intensity Intensity Intensity Red

2 Red Red Green

3 Green Green Blue

4Blue

Blue/Indigo*

5 Strobe** Lime

6Strobe**

Group and Cell

LED indicators

Grouping

button

ETC Installation Guide

ColorSource Linear v1.7

ColorSource Linear v1.7 Page 10 of 20 ETC

Linear 2 in Cell mode

*Original ColorSource Linear fixture uses blue; Deep Blue fixture uses indigo.

**Use DMX values of 0 or 255 for no strobe. Use values of 1–254 to increase

the strobe rate from 1 per second up to 33 per second.

DMX

Channel



(5 Channel)



(Direct)



(1 Channel)



(RGB)

Cell 1

Intensity

Cell 1

Intensity

Cell 1

Red

2 Red Red

Intensity Green

3 Green Green Blue

4Blue

Blue/Indigo*

Cell 2

Red

5 Strobe** Lime Green

Cell 2

Intensity Strobe Blue

7Red

Cell 2

Intensity

8Green Red

9Blue Green

10 Strobe**

Blue/Indigo*

11 Lime

12 Strobe**

Altri manuali per ColorSource Linear

Indice

Altri manuali ETC Attrezzatura per DJ

ETC

ETC ColorSource Spot Pearl v1.7 Manuale utente

ETC

ETC High End Systems SolaWash 1000 Manuale utente

ETC

ETC Source 4WRD Manuale utente

ETC

ETC ColorSource PAR v1.7 Manuale utente

ETC

ETC Element Manuale utente

ETC

ETC Source Four jr Manuale utente

ETC

ETC Irideon FPZ Manuale utente

ETC

ETC Source Four Mini LED Manuale utente

ETC

ETC Prodigy FlyPipe Studio Manuale utente

ETC

ETC ColorSource Fresnel V Manuale utente

ETC

ETC Source Four LED S4LEDLS Manuale utente

ETC

ETC Source Four LED Series Manuale utente

ETC

ETC Ion Classic Manuale utente

ETC

ETC Desire series Manuale utente

ETC

ETC SolaPix 19 XT Manuale utente

ETC

ETC High End Systems SolaPix 19 Manuale utente

ETC

ETC ColorSource Spot V 1.0 Manuale utente

ETC

ETC Desire series Manuale utente

ETC

ETC Source Four Mini LED Manuale utente

ETC

ETC ColorSource PAR Manuale utente

ETC

ETC ColorSource Manuale utente

ETC

ETC Desire D22 Manuale utente

ETC

ETC Source Four Mini LED Manuale utente

ETC

ETC fos/4 Series Manuale utente

Manuali Attrezzatura per DJ popolari di altre marche

ALPHA LITE

ALPHA LITE ALPHA 1500 Manuale del proprietario

Chauvet

Chauvet OVATION E-930VW Manuale utente

Zumtobel

Zumtobel APHRODITE Home Manuale utente

Snow Masters

Snow Masters Zig Oscillator Manuale utente

EuroLite

EuroLite 50530554 Manuale utente

Beamz

Beamz BUV243 Manuale utente

thomann

thomann Stairville DJ Lase 40-G MK-III Manuale utente

Eagletone

Eagletone 6 Eyes Flower Manuale utente

EuroLite

EuroLite FLD-1508 Manuale utente

Technical Pro

Technical Pro LG8xSEA Manuale utente

JB Systems

JB Systems Lounge Laser DMX Manuale utente

Lightmaxx

Lightmaxx Vega Halo 90 Manuale utente

Elation

Elation FUZE WASH Z350 Manuale utente

Maverick

Maverick MK3 WASH Manuale utente

Infinity

Infinity TF-260C7 Fresnel Manuale utente

Chauvet

Chauvet EVE E-50Z Manuale utente

Eliminator Lighting

Eliminator Lighting E 138 Manuale utente

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manuale utente