EtherWAN EL100T Manuale utente

Media Converter

User’s Manual 1

Preface

This manual describes how to install and use the Ethernet Media

Converter with the link-fault-pass-through function. The Converter

introduced here provides one channel media conversion between

10/100Base-TX and 100Base-FX/BX.

The Converter fully complies with IEEE802.3 10Base-T and IEEE802.3u

100Base-TX/FX standards.

In this manual, you will find:

Product overview

Features on the media converter

Illustrative LED functions

Installation instructions

Specifications

Media Converter

2 User’s Manual

Table of Contents

PREFACE ...............................................................................................................1

TABLE OF CONTENTS ............................................................................................2

INTRODUCTION .....................................................................................................3

PRODUCT OVERVIEW ............................................................................. 3

PRODUCT FEATURES ............................................................................. 3

PACKING LIST........................................................................................ 4

ONE-CHANNEL MEDIA CONVERTER .....................................................................5

PORTS................................................................................................... 5

PORT SETTINGS..................................................................................... 5

FRONT PANEL &LEDS........................................................................... 6

LINK-FAULT-PASS-THROUGH................................................................. 6

INSTALLATION ......................................................................................................8

SELECTING A SITE FOR THE EQUIPMENT................................................. 8

CONNECTING TO POWER........................................................................ 8

INSTALLING IN A CHASSIS....................................................................... 8

SPECIFICATIONS....................................................................................................9

Media Converter

User’s Manual 3

Introduction

The media converter provides one channel for media conversion between

10/100Base-TX and 100Base-FX/BX. It can be used as a stand alone

device or with a standard 19” chassis as shown below.

Product Overview

<NOTE> The chassis is to be ordered separately.

Product Features

One-channel media conversion between 10/100Base-TX and 100Base-FX/BX

Fiber media allows:

Multi-mode fiber using SC, ST, VF-45, MT-RJ or LC connector

Single-mode fiber using SC or ST connector

Auto negotiation of speed and duplex mode on TX port

Auto MDIX on TX port

One DIP switch for configuring link-fault-pass-through, fixed speed, and half/full duplex

768K bits buffer memory

Store-and-forward mechanism

Non-blocking full wire-speed forwarding rate

Support broadcast storm filtering

Back-pressure & IEEE802.3x compliant flow control

Front panel status LEDs

External AC to DC power adapter

Used as a stand-alone device or with a chassis

Hot-swappable when used with a chassis

<Note> The unit must use UL approved optical transceivers.

Media Converter

4 User’s Manual

Packing List

When you unpack this product package, you will find the items listed below.

Please inspect the contents, and report any apparent damage or missing

items immediately to our authorized reseller.

The Media Converter

User’s Manual

AC to DC Power Adaptor

Media Converter

User’s Manual 5

One-Channel Media Converter

Ports

The Converter provides one TX port and one FX/BX port. For the FX/BX

port, it provides options of:

Multi-mode fiber using SC, ST, VF-45, MT-RJ or LC connector or

Single-mode fiber using SC or ST connector

For the TX port, it uses RJ-45 connector and auto senses the speed of

10/100Mbps.

Port Settings

Port settings are made very simple by means of a DIP (Dual Inline

Package) switch at the rear panel of the module.

DIP switch

There are six pins on the DIP switch for port settings. Refer to the table below for more details.

DIP

switch

No.

Down

Enable LFPT

Disable LFPT

LFPT:

link-fault-pass-

through

Enable auto negotiation for TX port

Enable forced mode for TX port

TX port forced to 100Mbps

TX port forced to 10Mbps

TX port forced to full duplex mode

TX port forced to half duplex mode

FX port forced to full duplex mode

FX port forced to half duplex mode

First, disconnect the converter from the power. Then toggle Pin 2 of the DIP switch to the up position

to enable the forced mode for TX port.

<NOTE> Pin 2 must be toggled up prior to speed and duplex mode settings manually.

Toggle down Pin 3 to force the TX port at the speed of 100Mbps. Or toggle up Pin 3 for 10Mbps

speed.

Toggle down Pin 4 to force the TX port at full duplex mode. Or toggle up Pin 4 for half duplex mode.

Toggle down Pin 5 to force the FX port at full duplex mode. Or toggle up Pin 5 for half duplex mode.

Toggle up Pin 1 to disable the link-fault-pass-through.

Connect the converter to the power again. The new setting will come into effect then.

1 2 3 4 5 6

Media Converter

6 User’s Manual

Front Panel & LEDs

LED Indicators

The LED indicators give you instant feedback on status of the converter:

LEDs

State

Indication

PWR

Steady

Power on

PWR stands for POWER

Off

Power off

100 (Mbps)

Steady

Connection at the speed of 100Mbps

Off

Connection at the speed of 10Mbps

LNK/ACT

Steady

A valid network connection established

LNK stands for LINK

Flashing

Transmitting or receiving data

ACT stands for ACTIVITY

Off

Neither valid network connection established

nor transmitting/receiving data

FDX/COL

Steady

Connection in full-duplex mode

FDX stands for FULL-DUPLEX

Flashing

Collision occurred

COL stands for COLLISION

Off

Connection in half-duplex mode

Link-Fault-Pass-Through

Connect the FX ports of two Media Converter A and B through the fiber

cable.

Link Fault of the FX port:

A Link Fault condition will be sensed on the TX port whenever the media

converter detects a Link Fault condition on the FX port. Thus, the 100,

LNK/ACT, and FDX/COL LEDs of the media converter would be off.

Link Fault of the TX port of the Media Converter A:

The Media Converter A: A Link Fault condition will be sensed on the FX

port whenever the media converter detects a Link Fault condition on the

TX port. Thus, the 100, LNK/ACT, and FDX/COL LEDs of the TX port of

the Media Converter A would be off.

The Media Converter B: A Link Fault condition will be informed to the FX

port of the Media Converter B. Then a Link Fault condition will be sensed

on the TX port of the Media Converter B whenever the Media Converter B

detects a Link Fault condition on the FX port. Thus, the 100, LNK/ACT, and

FDX/COL LEDs of the Media Converter B would be off.

Media Converter

User’s Manual 7

Link Fault of the FX port

TX Port

FX Port

LEDs

PWR

100

LNK/ACT

FDX/COL

LNK/ACT

FDX/COL

Media

Converter

OFF

Media

Converter

OFF

Link Fault of the TX port of the Media Converter A

TX Port

FX Port

LEDs

PWR

100

LNK/ACT

FDX/COL

LNK/ACT

FDX/COL

Media

Converter

OFF

Media

Converter

OFF

Media Converter

8 User’s Manual

Installation

This chapter gives step-by-step installation instructions for the Converter.

Selecting a Site for the Equipment

As with any electric device, you should place the equipment where it will

not be subjected to extreme temperatures, humidity, or electromagnetic

interference. Specifically, the site you select should meet the following

requirements:

The ambient temperature should be between 32 and 113 degrees Fahrenheit (0 to 45 degrees

Celsius).

The relative humidity should be less than 95 percent, non-condensing.

Surrounding electrical devices should not exceed the electromagnetic field (RFC) standards for

IEC 801-3, Level 2 (3V/M) field strength.

Make sure that the equipment receives adequate ventilation. Do not block the ventilation holes

on each side of the equipment.

The power outlet should be within 1.8 meters of the product.

Connecting to Power

This Converter is a plug-and-play device.

Connect the supplied AC to DC power adaptor to the receptacle on the rear panel of the converter,

and then attach the plug into a standard AC outlet.

Installing in a Chassis

The Converter can be fit into any of the expansion slots on a special

designed chassis.

First, install the converter onto a carrier supplied with the chassis:

Step 1- Unscrew the carrier from the desired expansion slot on the chassis.

Step 2- Fit the converter onto the carrier.

When the converter is completely seated onto the carrier, insert the carrier to the guide rails of the

expansion slot.

Carefully slide in the carrier until it is fully and firmly fit the chassis. Fasten the screws onto the

carrier.

<NOTE> Never insert any converter into the chassis directly without using the

supplied carriers. The carriers allow secure and consistent placement of the

converters into the chassis’ backplane without causing any damage.

Media Converter

User’s Manual 9

Specifications

Applicable Standards

IEEE 802.3 10Base-T

IEEE 802.3u 100Base-TX & 100Base-FX

Fixed Ports

1 TX port, 1 FX/BX port

10Base-T speed

100Base-TX speed

100Base-FX/BX speed

10/20Mbps for half/full-duplex

100/200Mbps for half/full-duplex

200Mbps for full-duplex

Switching Method

Store-and-Forward

Forwarding rate

14,880/148,810pps for 10/100Mbps

LED Indicators

Per Unit- (2 LEDs): Power; 100(Mbps)

Per Port- (2 LEDs): LNK/ACT; FDX/COL

Dimensions

80.3mm (W) × 109.2mm (D) × 23.8mm (H)

(3.16”(W) × 4.30”(D) × 0.94” (H))

Weight

150g (0.33lb.)

Power

External power adaptor 0.16A @ 12VDC

Power Consumption

1.92W Max.

Operating Temperature

0℃~ 45℃(32℉~ 113℉)

Storage Temperature

-10℃~ 70℃(14℉~ 158℉)

Humidity

5 ~ 95%, non-condensing

Safety

UL60950-1

Emissions

FCC Part 15 Class A, CE Mark Class A

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali EtherWAN Convertitore multimediale

EtherWAN

EtherWAN EL100 Manuale utente

EtherWAN

EtherWAN EMC400 Manuale utente

EtherWAN

EtherWAN EX42011 Manuale utente

EtherWAN

EtherWAN EL2242 Series Manuale utente

EtherWAN

EtherWAN EL2321 Manuale utente

EtherWAN

EtherWAN EL1141 Series Manuale utente

EtherWAN

EtherWAN EL50 Series Manuale utente

EtherWAN

EtherWAN EL8000 Manuale utente

EtherWAN

EtherWAN EL1033 Manuale utente

EtherWAN

EtherWAN EL1032T Series Manuale utente

EtherWAN

EtherWAN EL9020 Manuale utente

EtherWAN

EtherWAN EL2326 Series Manuale utente

EtherWAN

EtherWAN EMC1200R Manuale utente

EtherWAN

EtherWAN EL900 Series Manuale utente

EtherWAN

EtherWAN EL2242 Series Manuale utente

EtherWAN

EtherWAN EL900 Series Manuale utente

EtherWAN

EtherWAN EL110 Series Manuale utente

EtherWAN

EtherWAN EL2242-BT Manuale utente

EtherWAN

EtherWAN EL2321 Manuale utente

EtherWAN

EtherWAN EL2242 Manuale utente

EtherWAN

EtherWAN EMC1200R Manuale utente

EtherWAN

EtherWAN EL900 Series Manuale utente

EtherWAN

EtherWAN EL2211 Manuale utente

EtherWAN

EtherWAN EL100 Manuale utente

Manuali Convertitore multimediale popolari di altre marche

SoundTraxx

SoundTraxx Blunami BLU-2200 Manuale utente

SPROLINK

SPROLINK VA1 Manuale utente

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manuale utente

Nikon

Nikon AF-S TC-20E III Manuale utente

Axis

Axis AXIS Q7406 Manuale utente

Omega

Omega TAC80B-J Manuale utente

Zoom

Zoom Thunderbolt TAC-2R Manuale utente

OST

OST iConverter 10/100M Manuale utente

Vertiv

Vertiv Netsure Manuale utente

birddog

birddog MINI Manuale utente

Roland

Roland GI-10 Manuale utente

Wallenstein

Wallenstein WX310 Manuale utente

Pace

Pace MSS 200-1 Manuale utente

Solar Converters

Solar Converters EQ 12/24-50 Manuale utente

CYP

CYP EL-7400V Manuale utente

TIE

TIE MIDI 1i1o Manuale utente

DCS

DCS Vivaldi Upsampler Manuale utente

Westermo

Westermo MCW-211 SERIES Manuale utente