EtherWAN EG97000 Series Manuale utente
Copyright 2018 EtherWAN Systems, Inc. Page 1
All Rights Reserved
EG97000
12/18/2018
W70G-EG97000Q1
1 Unpacking
Open the carton and unpack the items. Your
package should include:
EG97000 Ethernet switch
2 Mounting brackets
12 Mounting screws
1 Console cable
1 AC Power Cord (optional)
Quick install guide
If any items are missing or damaged, notify your
EtherWAN representative. If possible, save the
carton and packing material in case you need to
ship or store the switch in the future. The full
product manual can be downloaded from:
https://www.etherwan.com/support/product/E
G97000-series
2 What Else You Need
Shielded twisted pair cables and corresponding
shielded RJ45 connectors
Appropriate SFP cable and SFP modules for SFP
ports
3 Select a Location
Installation: Rack-mount. Use the enclosed screws
and brackets to mount the switch in an open or
enclosed rack.
Select a power source within 6 feet (1.8 meters).
Choose a dry area with ambient temperature
between -40 and 75ºC (-40 and 167ºF).
Be sure there is adequate airflow.
4 Connect to the Data Ports
The EG97000 has the following ports:
8 x 10/100/1000 Mbps copper ports
16 x 100/1000 SFP slots
4 x 1/10G SFP+ slots
1 x RJ-45 Management port
1 x USB port
100/1000BASE-TX Ports
Ports 1 to 8 are gigabit copper ports and can be
connected to routers, other switches, or end
devices.
1 Gbps SFP Slots
Ports 9 –24 are 1 Gbps SFP slots, for connection
with stackable switches to form multiple fiber
interconnections. Use appropriate SFP tranceivers.
1/10 Gbps SFP+ Slots
SFP+ ports 1 –4 are for uplink connection to core
networks. Ensure that the same type of transceiver
is used at both ends of the link and that the correct
type of fiber cable is used.
5 Connect Power
Terminal Block
If your EG97000 comes with AC power cables,
connect the cables into the power modules at the
back of the switch. If your switch comes with a DC
or AC terminal block (no cable), then connect the
switch to a suitable power supply using 12 to 24
AWG wire. Redundant power supply is supported.
However, only one power input is required to
operate the switch. Input voltage is 48 VDC or 100 –
240 VAC, depending on model.
EG97000 Series Layer 3 Hardened Managed Ethernet Switch
Installation Guide
EG97000 Layer 3 Hardened Managed Ethernet Switch
Copyright 2018 EtherWAN Systems, Inc. Page 2
All Rights Reserved
EG97000
12/18/2018
W70G-EG97000Q1
Relay Output Alarm
The switch provides one dry contact for signaling of
a user-defined power or port failure. The alarm
relay default is “open” and forms a closed circuit
when the event occurs. The relay output can be
connected to an alarm signaling device. Relay
output current is 30VDC / 0.6A.
NOTE: The initial normal state of the relay is open,
and if switch loses *all* power, then this state will
come into effect. This is important to remember
when using the relay to indicate a power failure.
The relay will close in an alarm state when there is
redundant power input and an alarmed input fails.
6 Front Panel LEDs
Link/Act
Green: Network connection established
Flashing: Port sending or receiving data
Red: Link down or power down
Reset Button: Press and hold for less than 10
seconds to reboot the switch. Press and hold for
more than 10 seconds to reset the switch to the
default password.
7 Initial Configuration
Connect to the switch using the enclosed Ethernet
cable to connect a serial port on a PC to the RJ-45
Management port located on the front panel next
to the USB port. You can also use regular Ethernet
cable to connect the RJ-45 port on the PC to any of
the TX ports 1 - 8. The IP address of VLAN 1 is
192.168.1.10.
Configuration via CLI
If using a terminal-emulation program such as Putty,
configuration settings are: Baud rate: 115,200bps,
Data bits: 8, Parity: none, Stop bit: 1, Flow control:
none.
The default login name is “root,” no password.
Configuration via Web Browser
Log in to the switch by launching a web browser
and entering 192.168.1.10 in the address bar.
Enter the default login ID: root (no password) and
click “Login.” The system information screen will
display.
8 Copy Configuration to USB
The USB port can be used to save the running
switch configuration to a (FAT32) USB storage
device. Plug the device into the USB port, and use
the “Save Configuration” command in the web
interface, or “copy running-config startup-config”
in the CLI.
Altri manuali EtherWAN Interruttore
EtherWAN
EtherWAN EX33000 Series Manuale utente
EtherWAN
EtherWAN EX87000 Series Manuale utente
EtherWAN
EtherWAN EX46900A Series Manuale utente
EtherWAN
EtherWAN EX77000 Series Manuale utente
EtherWAN
EtherWAN EX17162A Manuale utente
EtherWAN
EtherWAN EX78900 Series Manuale utente
EtherWAN
EtherWAN EX34000 Manuale utente
EtherWAN
EtherWAN EX19082 Manuale utente
EtherWAN
EtherWAN EG97023 Series Manuale utente
EtherWAN
EtherWAN EX78000R Manuale utente
EtherWAN
EtherWAN EX17908 Series Manuale utente
EtherWAN
EtherWAN EX26484 Series Manuale utente
EtherWAN
EtherWAN ER59000 Series Manuale utente
EtherWAN
EtherWAN EX77900 Series Manuale utente
EtherWAN
EtherWAN EX33000 Series Manuale utente
EtherWAN
EtherWAN EX32008 Series Manuale utente
EtherWAN
EtherWAN EX42914 Series Manuale utente
EtherWAN
EtherWAN EX26484 Manuale utente
EtherWAN
EtherWAN EX89000 Manuale utente
EtherWAN
EtherWAN EX43000 series Manuale utente
