EtherWAN EX1624W Manuale utente
24-Port Web-Smart Ethernet Switch
User’s Manual 1
FCC Statement
The FCC (Federal Communications Commission) restricts
the amount of radio frequency emission and radiation coming
from computer equipment.
The equipment introduced in this manual has been tested
and found to comply with the limits for a Class A digital
device pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment.
This equipment generates, uses, and can radiate radio
frequency energy, and if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user is required
to correct the interference at his/her own expense.
Any changes or modifications not expressly approved by the
manufacture would void the user’s authority to operate the
equipment.
Trademarks
Product names mentioned in this manual may be trademarks
or registered trademarks of those products.
All trademarks or brand names mentioned are properties of
their respective companies.
24-Port Web-Smart Ethernet Switch
User’s Manual
2
Preface
This manual describes how to install and use the 24-Port Web-
Smart Ethernet Switch. The TX ports of the switch introduced here
auto-negotiates the presence of 10/100Mbps and full/half-duplex
mode and auto-MDIX. In addition, it allows an optional 100Base-
FX multi-mode or single-mode fiber module, enabling long
distance connection.
To get the most out of this manual, you should have an
understanding of networking concepts such as bridging, IEEE
802.3 10Base-T Ethernet, IEEE 802.3u 100Base-TX/FX Fast
Ethernet, and local area networks (LANs).
For more information about these topics, please refer to the
Appendices.
In this manual, you will find:
•Introduction on the Switch
•Product features
•Illustrative LEDs functions
•Installation instructions
•Specifications
24-Port Web-Smart Ethernet Switch
User’s Manual 3
Table of Contents
FCC STATEMENT 1
TRADEMARKS 1
PREFACE 2
TABLE OF CONTENTS 3
PRODUCT OVERVIEW 5
FRONT VIEW 5
PACKAGE CONTENTS 5
PRODUCT FEATURES 6
FRONT PANEL DISPLAY 7
PHYSICAL PORTS 8
Understanding Front Panel Design 8
INSTALLATION 9
SELECTING A SITE FOR THE EQUIPMENT 9
INSTALLATION AND PLACEMENT INSTRUCTIONS 10
Mounted to 19-inch standard rack 10
Desktop or any flat surface 10
OPTIONAL FIBER MODULE INSTALLATION 11
CONNECTING TO POWER 12
CONNECTING TO YOUR NETWORK 12
Cabling 12
Network Segmentation 13
SWITCH CONFIGURATION 14
SETTING UP CONSOLE PORT CONNECTION (WEB-BASED BROWSER
INTERFACE) 14
LOGGING ON TO THE ETHERNET SWITCH 14
Switch IP Address 14
User Name 14
Password 14
MAIN MENU 15
System Change 15
IP Configuration 16
24-Port Web-Smart Ethernet Switch
User’s Manual
4
Port 17
VLAN 18
Trunking 19
Save Configuration 20
Load Default 21
TECHNICAL SPECIFICATIONS 22
PHYSICAL SPECIFICATIONS 23
CONNECTOR PINOUTS 24
ORDERING INFORMATION 25
24-Port Web-Smart Ethernet Switch
User’s Manual 5
Product Overview
Front View
Figure 1: 24-Port Web-Smart Ethernet Switch
Package Contents
When you unpack the product package, you shall find these items
listed below.
3
The 24-Port Switch
3One AC power cord
3
User’s Manual
Please inspect the contents, and report any apparent damage or
missing items immediately to your authorized reseller.
24-Port Web-Smart Ethernet Switch
User’s Manual
6
Product Features
♦PROVIDES 24 ×10/100MBPS PORTS USING RJ-45
CONNECTORS
♦AN OPTIONAL SINGLE-PORT FIBER MODULE ALLOWS:
-100BASE-FX MULTI-MODE FIBER WITH SC, ST, MT-RJ, VF-45 OR LC
CONNECTOR
-100BASE-FX SINGLE-MODE FIBER WITH SC CONNECTOR
♦AUTO-NEGOTIATION FOR SPEED AND DUPLEX MODE ON TX
PORTS
♦8192 MAC ADDRESSES,1.5M BITS BUFFER MEMORY
♦AUTO-MDIX FOR ALL TX PORTS
♦STORE-AND-FORWARD MECHANISM
♦TRUE NON-BLOCKING ARCHITECTURE
♦FULL WIRE SPEED FORWARDING RATE
♦BROADCAST STORM FILTERING CONTROL
♦BACK-PRESSURE AND IEEE 802.3X COMPLIANT FLOW
CONTROL
♦SYSTEM,IP CONFIGURATION,PORT,PORT-BASED VLAN,
AND PORT-BASED TRUNKING SETTING THROUGH THE WEB-
BASED CONSOLE PORT.
♦FRONT PANEL PUSH BUTTON TO CHOOSE 100BASE-FX OR
PORT 24
♦PRESS THE FRONT PANEL IP RESET PUSH BUTTON FOR
FIVE SECONDS TO RESET THE ETHERNET SWITCH BACK TO
THE DEFAULT IP ADDRESS.(THE PORT,VLAN, AND
TRUNKING SETTINGS WILL REMAIN THE SAME AS WHEN
THEY WERE LAST SAVED).
♦FRONT PANEL PORT AND POWER STATUS LEDS
♦STANDARD 19” RACKMOUNT SIZE,ONE-UNIT IN HEIGHT
24-Port Web-Smart Ethernet Switch
User’s Manual 7
Front Panel Display
The LED indicators on the front panel provide you with instant
feedback on each port status, and help you monitor and
troubleshoot the switch.
Figure 2: Front Panel LEDs
Power
This LED comes on when the switch is properly connected to power and
turned on.
Push Button
The push button is located at the right side of port 24 on the 24-Port Switch.
Depress this button to use twisted pair port 24, and press this button to use
the 100Base-FX module.
IP RESET Push Button
Press the Front panel IP RESET push button around five seconds to reset
the Ethernet Switch back with the default IP Address.
Port Status
The RJ-45 ports are numbered from 1 to 24 on the 24-Port Switch.
The LEDs are located on the ports of the switch, displaying status for each
respective port. Please refer to the table below for more information.
Consult the following table for details.
LBefore you use this table for troubleshooting, make sure the switch is
properly connected to power and turned on.
24-Port Web-Smart Ethernet Switch
User’s Manual
8
Physical Ports
The 24-Port Switch has twenty-four 10/100Mbps ports using RJ-45
connectors and provides one slot for the optional single-port fiber
module. The optional module allows fiber type (multi-mode or
single-mode fiber) and connector (SC, ST, MT-RJ, VF-45, or LC)
at user’s discretion.
UNDERSTANDING FRONT PANEL DESIGN
On Power feeding in
Power switched off
Power LED
Off
Improper connection
On A valid network connection
LNK stands for LINK
LNK
Off No connection
Flashing Transmitting or receiving data
ACT stands for ACTIVITY
Console
Port LED
ACT
Off Neither transmitting nor receiving
data
On A valid network connection
LNK stands for LINK
Flashing Transmitting or receiving data
ACT stands for ACTIVITY
LNK/ACT
Off Neither connection nor activity
On A valid 100Mbps connection
Port LED
SPEED
Off A valid 10Mbps connection
On A valid network connection
LNK stands for LINK
LNK
Off No connection
Flashing Transmitting or receiving data
ACT stands for ACTIVITY
100FX Port
LED
ACT
Off Neither transmitting nor receiving
data
24-Port Web-Smart Ethernet Switch
User’s Manual 9
Installation
Selecting a Site for the Equipment
As with any electric device, you should place the equipment where
it will not be subjected to extreme temperatures, humidity, or
electromagnetic interference. Specifically, the site you select
should meet the following requirements:
- The ambient temperature should be between 0 to 45 degrees
Celsius.
- The relative humidity should be less than 95 percent,
non-condensing.
- Surrounding electrical devices should not exceed the
electromagnetic field (RFC) standards for IEC 801-3, Level 2
(3V/M) field strength.
- Make sure that the equipment receives adequate ventilation.
Do not block the ventilation holes on each side of the switch or
on the rear of the equipment.
-The power outlet should be within 6 feet (1.8 meters) of the
switch.
24-Port Web-Smart Ethernet Switch
User’s Manual
10
Installation and Placement Instructions
MOUNTED TO 19-INCH STANDARD RACK
Locate the accessories supplied in the product package. Use the
rackmount brackets and screws to install the switch into any EIA
19” standard rack.
Step 1: Attach the brackets to each side of the chassis.
Step 2: Apply the screws to each side and secure them tightly.
Step 3: Carefully position the switch into the rack.
Step 4: Align the brackets to the side holes on the rack and use rack
screws to secure the chassis with the rack.
Step 5: Proceed to the “Connecting to Power” section.
DESKTOP OR ANY FLAT SURFACE
The switch can sit on desktop or any flat surface with adequate
space and ventilation. If you want to place it onto a shelf, make
sure the shelf can withstand the weight of the switch.
Step 1: Simply put the switch on the desired place.
Step 2: Ensure the switch receives good ventilation.
Step 3: Proceed to the “Connecting to Power” section.
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali EtherWAN Interruttore
EtherWAN
EtherWAN EX70900 Manuale utente
EtherWAN
EtherWAN EX45900 series Manuale utente
EtherWAN
EtherWAN EX16926 Manuale utente
EtherWAN
EtherWAN EX63000 Series | Manuale utente
EtherWAN
EtherWAN ER58000 Series Manuale utente
EtherWAN
EtherWAN EX45000 Series Manuale utente
EtherWAN
EtherWAN EX73900 Series Manuale utente
EtherWAN
EtherWAN EX48050-00B Manuale utente
EtherWAN
EtherWAN EX83304 Series Manuale utente
EtherWAN
EtherWAN EX75900 Series Manuale utente
EtherWAN
EtherWAN EX17016 Manuale utente
EtherWAN
EtherWAN EX41941F Manuale utente
EtherWAN
EtherWAN EX78900 Series Manuale utente
EtherWAN
EtherWAN EX87000 Series Manuale utente
EtherWAN
EtherWAN EX78000 Series Manuale utente
EtherWAN
EtherWAN EG97000 Series Manuale utente
EtherWAN
EtherWAN EX76000 Series Manuale utente
EtherWAN
EtherWAN EX33000 Series Manuale utente
EtherWAN
EtherWAN EG97000 Series Manuale utente
EtherWAN
EtherWAN EX75900 Series Manuale utente
