3
EXCURSION
It is recommend that you have your new Series Automove
Speakers professionally installed by your authorizied dealer. This
will ensure use of proper installaon techniques and materials and save much
me and efforts. If you choose to perform your own installaon, the following
instrucon will give you direcon toward making your purchase complete. Read
the following informaon and precauons carefully.
EXCURSION SHX
EXCURSION
Failure to follow the stated
precauons may result in personal injury or damage the audio system or vehicle.
A.) Always make sure the speaker will easily fit into the intended mounng locaon
and that there is adequate cavity depth to accept the magnet structure.
B.) Check for adequate clearance between speaker and window, window crank,
power window mechanism, seat, glove box, rear deck torsion bars and other
items which may interfere with the speaker`s mounng. This is especially
important if any hole cung is required. Complete speaker, mounng size and
depth requirements can be found on page 9 of these instrucons. A good way to
confirm speaker place meet on a door or body panel is to place the speaker`s
die cast mounng ring onto the surface. Check for a flat mounng surface,
free from all obstrucon.
C.) The method of installaon choosen and level of execuon will effect the
overall performance of the Speakers. Thread each installaon
step with a high degree of aenon.
D.) Do not mount the speaker where water may splash the woofer cone.
A plasc cup or some heavy gauge plasc sheeng may be needed in some
locaons that are exposed to moisture from behind the body panel.
E.) Care must be taken to prevent low frequency cancelaon caused by air
leakage between the front and rear of the speaker (such as when mounted
on a curved or uneven surface, or when mounted in an oversized hole)
F.) Mounng panel reinformcement may be necessary in some cases in order
to prevent surface flex. This can be achieved by mounng the speaker on a
metal or wooden sub-baffle behind the body or door panel.
EXCURSION
Consult an installaon specialst for further direcon.
Pre-Installaon Instrucons:
4
G.) Unless you are replacing exisng speakers of same size, mounng locaons
will have to be cut into the doors, body panels or rear deck. In some cases
speaker mounng holes will be precut in the doors, bodypanels, or rear
deck steel. Due to their structural integrity and accessibility. These precut
mounng holes should be used whenever possible.
: IMPORTANT Never cut any metal that is an integral part of an automobile`s
safety or structural support system.
: NOTE EXCURSION strongly recommends that you operate the complete
audio system at low volume before final installaon of your Series
Automove Loudspeakers. This will allow a trial listening test before
securing the loudspeakers into their mounng locaons.
Make sure that all speaker wiring is fully protected from cung
or wear. Any short circuits developing as a result could severaley damage
the radio unit or amplifier. Make sure that all speaker wires easily reach the
speaker terminals without stress on the wire or connectors.
SX
CAUTION:
PREPARING FOR INSTALLATION
Note: The tools listed below may be required for proper installaon.
* An elecric drill with drill bits
* Phillips-head and standard screwdrivers
* Crimping tool and needle-nose pliers
* Silicon sealant or closed cell weather-stripping
* Metal file, Hole saw, Tin Snips, Wire strippers
INSTALLATION PRECAUTIONS
Note: Proceed only if you are a qualified installer otherwise let your dealer do it.
* Always wear protecve eyewear when using tools
* Turn all stereo and other electrical devices before you begin
* Disconenect the (-) negave lead from your vehicle`s baery.
* Keep the speakers in the package unl final installaon.
* Locate fuel lines, brake lines, oil lines, electrical cables when planning installaon.
* Check to see clearance behind the mounng surface before installing speakers.
* When running speaker wires through sheet metal, be sure to use gromments
to properly insualte the wires from metal edges.
OFF
