Extech Instruments 42311 Manuale utente

User’s Guide

Digital Thermocouple

Calibrator & Thermometer

Models:

42311 Type J

42312 Type K

Introduction

Congratulations on your purchase of Extech model 42311 or 42312 Digital Thermometer and

Calibrator. Properly used, this meter will provide many years of reliable service.

V1.5 1/03

WARRANTY

EXTECH INSTRUMENTS CORPORATION warrants this instrument to be free of defects in

parts and workmanship for one year from date of shipment (a six month limited warranty

applies on sensors and cables). If it should become necessary to return the instrument for

service during or beyond the warranty period, contact the Customer Service Department at

(781) 890-7440 ext. 210 for authorization. A Return Authorization (RA) number must be

issued before any product is returned to Extech. The sender is responsible for shipping

charges, freight, insurance and proper packaging to prevent damage in transit. This warranty

does not apply to defects resulting from action of the user such as misuse, improper wiring,

operation outside of specification, improper maintenance or repair, or unauthorized

modification. Extech specifically disclaims any implied warranties or merchantability or fitness

for a specific purpose and will not be liable for any direct, indirect, incidental or consequential

damages. Extech's total liability is limited to repair or replacement of the product. The

warranty set forth above is inclusive and no other warranty, whether written or oral, is

expressed or implied.

Safety Precautions

1. Make sure any covers or battery doors are properly closed and secured.

2. Remove the battery from the meter if the meter is to be stored for long periods.

3. Touching the thermocouple to a device which is powered electrically can cause

damage to the meter and may pose a shock hazard.

4. To avoid damage do not make temperature measurements in microwave ovens.

Specifications

Display 3 ½ digit (1999 Count) LCD (Liquid Crystal Display)

Temperature Scale ºC or ºF (user-selectable)

Thermocouple type Model 42311: type J; Model 42312: type K

Measurement and Model 42312: -40º to 2000ºF (-40º to 1350ºC)

Source Ranges Model 42311: -40º to 1400ºF (-40º to 760ºC)

Resolution 1ºC/F or 0.1ºC/F (< 200ºF/C)

Accuracy ±(0.1% rdg + 2ºF) or ±(0.1% rdg + 1ºC)

Temp. Coefficient 0.1 times the applicable accuracy spec per ºC or ºF from

32º to 64ºF and 82º to 122ºF (0º to 18ºC and 28º to 50ºC)

Input Protection 24VDC or 24VAC RMS maximum input voltage

Display Update 2.5 times per second

Input Connector Accepts standard subminiature thermocouple connectors

Battery 9V battery (200 hour typical battery life)

Dimensions/Weight 7.5x3.54x2.1 inches (190x90x53 mm) / 1 lb (440g)

V1.5 1/03

Meter Front Panel Description

1. Display

2. C/F Selector Key

3. Low/High Resolution Key

4. Max Hold Key

5. Hold/Backlight Key

6. Function Switch

7. Course Adjustment Knob

8. Fine Adjustment Knob

Features

Selecting the Temperature Scale

Readings can be displayed in Celsius or Fahrenheit by pressing the ºC/ºF key. The ºC or

ºF annunciator will illuminate on the display depending on which scale you have selected.

Adjustable Resolution

The resolution of the meter can be switched from 0.1º (up to 199.9) to 1º by pressing the

0.1º/1º key.

Max Hold

Max hold will freeze the highest recorded reading on the display. When the MAX key is

pressed the MAX icon will appear in the upper portion of the display. The display will

update every time there is a new maximum reading. Pressing MAX again will disengage

Max hold.

Backlit display

Press the Hold key for 2 seconds to toggle the Backlight ON and OFF. The backlight will

stay on until you press the Hold key for 2 seconds again, or turn the meter off.

Data Hold

The hold function freezes the displayed reading for later viewing. Press the HOLD key

momentarily to activate the Data Hold feature. Press again to exit the Hold mode.

Operation

WARNING: To avoid electrical shock, do not use this instrument when voltages at the

measurement surface exceed 24VAC or DC.

Temperature Measurement

1. Plug a thermocouple into the T1 or T2 input jack.

2. Turn the function switch to the T1 or T2 position depending upon where the

thermocouple is physically connected per step 1 above.

3. Touch the temperature probe to the surface, liquid or gas being measured and

observe the reading on the display.

NOTE: Both T1 and T2 inputs can be used simultaneously, but only one reading can be

displayed at a time. Always move the rotary function switch to the OFF position

when the meter is not in use.

V1.5 1/03



Tech Support Hotlines

781-890-7440 ext. 200

[email protected]

www.extech.com

Temperature Calibration (Source)

NOTE: When calibrating temperatures over 199.9º you must change the resolution to

the 1º scale or the meter will display "OL"

1. Connect a thermocouple cable (Type J for Model 43211 or Type K for Model

43212) to output 1 or 2 at the top of the meter. These jacks have the same signal

available on both output 1 and output 2 terminals.

2. Connect the other end of the thermocouple cable to the instrument(s) to be

calibrated.

3. Using the range switch, coarse and fine adjustment knobs set the meter to the

desired output. See explanation below.

How to use the Range Switch and Coarse/Fine Adjustments

In addition to the T1, T2, and OFF positions, the Rotary switch has 7 output range positions

that move low to high (left to right) underneath the words Calibrator Output on the front panel

(also designated by the white strip over the Rotary switch).

1. Use the Rotary switch to find the closest range of the desired temperature output

2. Note that the meter outputs a mV signal corresponding to the temperature display

which can be routed to a panel meter, recorder, datalogger, controller, another

calibrator, etc.

3. Adjust the Coarse knob to dial in even closer to the desired output temperature

4. Finally, adjust the Fine knob for the exact temperature output

Maintenance

Cleaning and Storage

Periodically wipe the case with a damp cloth and mild detergent; do not use abrasives or

solvents. If the meter is not to be used for periods of longer than 60 days, remove the

battery and store it separately

Battery and Fuse replacement

1. Remove the protective rubber holster from the meter

2. The battery cover is held in place by two Philips head screws, both screws must be

removed in order to remove battery cover.

3. Remove and replace the 9V battery.

4. Replace compartment cover, screws and rubber holster.

Repair and Calibration Services

Extech offers complete repair and calibration services for all of the products we sell. For

periodic calibration, NIST certification or repair of any Extech product, call customer service

for details on services available. Extech recommends that calibration be performed on an

annual basis to ensure calibration integrity.

including the right of reproduction in whole or in part in any form.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Extech Instruments Termometro

Extech Instruments

Extech Instruments EA10 Manuale utente

Extech Instruments

Extech Instruments SDL200-NIST Manuale utente

Extech Instruments

Extech Instruments RHM15 Manuale utente

Extech Instruments

Extech Instruments 407445 Manuale utente

Extech Instruments

Extech Instruments HD200 Manuale utente

Extech Instruments

Extech Instruments IRC130 Manuale utente

Extech Instruments

Extech Instruments TM40 Manuale utente

Extech Instruments

Extech Instruments RH10 Manuale utente

Extech Instruments

Extech Instruments Extech 470 Manuale utente

Extech Instruments

Extech Instruments 42545 Manuale utente

Extech Instruments

Extech Instruments 445703 Manuale utente

Extech Instruments

Extech Instruments IR200 Manuale utente

Extech Instruments

Extech Instruments 421501 Manuale utente

Extech Instruments

Extech Instruments RH350 Manuale utente

Extech Instruments

Extech Instruments K.J.E.T. 422324 Manuale utente

Extech Instruments

Extech Instruments 42511 Manuale utente

Extech Instruments

Extech Instruments IR100 Manuale utente

Extech Instruments

Extech Instruments IR201A Manuale utente

Extech Instruments

Extech Instruments 39240 Manuale utente

Extech Instruments

Extech Instruments 445582 Manuale utente

Extech Instruments

Extech Instruments 445703 Manuale utente

Extech Instruments

Extech Instruments IR200 Manuale utente

Extech Instruments

Extech Instruments EA15 Manuale utente

Extech Instruments

Extech Instruments EA11 Manuale utente

Manuali Termometro popolari di altre marche

Delton

Delton 981A Manuale utente

Baker

Baker MM2P Manuale utente

Tarmo

Tarmo 320281 Manuale utente

Citizen

Citizen CTD 504 Manuale utente

TFA

TFA 14.1500 Manuale utente

Vive

Vive DMD1010 Manuale utente

Gotemp

Gotemp THB4002 Manuale utente

GREISINGER

GREISINGER G 1202 Manuale utente

Amprobe

Amprobe TMD-53W Manuale utente

Trotec

Trotec BP10 Manuale utente

Radiance instruments

Radiance instruments RT616 Series Manuale utente

Eurolec

Eurolec IR151 Manuale utente

Scaneo

Scaneo TS42B Manuale utente

Sper scientific

Sper scientific 800043 Manuale utente

Microlife

Microlife NC 200 Manuale di istruzioni

Motorola

Motorola MBP69SN Guida alla configurazione

The MeatStick

The MeatStick The MeatStick Manuale utente

Hama

Hama TH35-A Manuale utente