Extech Instruments 445580 Manuale utente

User's Manual

Hygro-Thermometer Pen

Models 445580 and 445582 (kit)

METER DESCRIPTION

1. Humidity/Temperature Sensor

2. POWER ON/OFF button

3. Data HOLD button

4. MIN/MAX Memory button

5. Calibration and units select button

6. Memory Reset button

7. Humidity Display

8. Temperature Display

9. Function Displays

INTRODUCTION

Congratulations on your purchase of the Extech Hygro-Thermometer Pen. This portable

meter can measure Relative Humidity from 10% to 90% and Temperature from 14 to 122oF

(0 to 50oC). Advanced features include MIN/MAX Memory, Push-button Calibration,

Display Hold, and Automatic Power Off. The Model 445582 kit includes Relative Humidity

Calibration bottles and hard shell carrying case.

SPECIFICATIONS

Relative Humidity Sensor High Precision thin-film capacitance type

Temperature Range 14 to 122oF (-10 to 50oC)

Relative Humidity Range 10 to 90% Relative Humidity

Resolution Temperature: 0.1o; Relative Humidity: 0.1%

Accuracy* Temperature: ±1.8oF (±1.0oC); Relative Humidity: ±5%

DC Power 2032 button battery (150 hour battery life)

Response time 120 seconds

Dimensions 6.9 x 1.6 x 0.6" (175 x 42 x 16mm)

* Accuracy applies to the temperature range 32 to 122oF (0 to 50oC)

Models 445580 & 445582 Version 3.2 August 2003

OPERATION

Measurements

Press the ON/OFF button to turn the meter ON. After a 5 second initialization, the Relative

Humidity reading will appear in the upper display and the Temperature reading will appear

in the lower display. Allow time for measurement readings to stabilize when moving the

meter from one area to another.

Error Messages

An error message will appear on the display if the meter fails an internal diagnostic test.

E2: Calibration error. Recalibration is necessary.

E5: Relative Humidity sensor failure. Repair/replacement is necessary.

Data Hold

1. Press the HOLD button to freeze the displayed reading. The display icon ‘HLD’ and the

held reading will appear on the display.

2. To return the meter to the normal operation mode, press and hold the RESET button

until the ‘HLD’ icon switches off.

MIN/MAX Memory Recall

1. Press and hold the MIN/MAX button until ‘MIN’ appears in the display. The reading will

then represent the lowest humidity and temperature measurements recorded since the

meter was turned on or last reset.

2. Press and hold the MIN/MAX button until the ‘MAX’ appears on the display. The

reading will then represent the highest humidity and temperature measurements

recorded since the meter was turned on or last reset.

3. Press the MIN/MAX key again to return to normal operation.

MIN/MAX Memory Reset

To reset (clear) the MIN/MAX memory, press and hold the RESET button until ‘88.8’

appears in the display.

Automatic Power Off (Sleep mode)

The meter will automatically shut off after a period of approximately 20 minutes. To defeat

this mode, press and hold the MIN/MAX button while turning the meter on. Release the

ON/OFF button after the display initializes. 'n' will appear on the display indicating that the

non-sleep mode has been activated. Sleep mode will be re-activated when the meter is

turned off however.

Setting Temperature Units (C or F)

Caution: Follow this procedure carefully. Accidentally pressing the RESET button during

this procedure will compromise the meter's calibration.

1. Ensure that the meter is off.

2. Press and Hold the recessed F/C button (use a paper clip or similar object) and then

press the ON/OFF button. The unit will power up and the display will flash once. When

only the ‘F’ and ‘C’ icons appear together in the display, release the F/C button.

3. The display will then show either ‘C’ or ‘F’. Press the MIN/MAX key to select degrees

‘C’ or ‘F’. The display will reflect the change.

4. Press the recessed F/C button to store the selection. ‘S’ will appear in the display.

5. The display will then show ‘%MIN’. Turn off the meter to complete the operation.

Models 445580 & 445582 Version 3.2 August 2003

CALIBRATION

The following verification and calibration procedures require the 33% and 75% RH

reference bottles which are supplied with the model 445582 kit.

Accuracy Verification

Checking the 33% or 75% RH Calibration

1. Insert meter’s sensor into the 33% or 75% salt reference bottle

2. Place the meter and bottle inside the meter case

3. Check the reading after 40 minutes

4. Verify that the reading is within the accuracy specification.

Relative Humidity Calibration (33% and 75%)

Note: For best results, store the meter and salts in the closed case during the 40-minute

stabilization process.

33% Calibration

1. Make sure the meter is OFF.

2. Insert the meter sensor into the 33% salt reference bottle. Allow the meter to

stabilize for 40 minutes.*

3. While holding down the recessed CAL button (use a paper clip) press and release

the ON/OFF button.

4. Continue to hold the CAL button and the unit will power up and the display will flash

once.

5. When only the ‘F’ and ‘C’ icons appear on the display, release the CAL button. ‘C’ or

‘F’ (whichever was previously selected) will remain on the display.

6. Press and hold RESET for 3 seconds ‘%MIN’ will appear when the key is released.

7. Momentarily press CAL. ‘S’ then ‘%MAX’ will display.

8. Turn power off. The 33% calibration is complete. Leave the meter OFF and proceed

to the 75% Calibration below.

75% Calibration

1. Make sure the meter is OFF.

2. Insert the meter sensor into the 75% salt reference bottle. Allow the meter to

stabilize for 40 minutes.*

3. While holding down the recessed CAL button (use a paper clip), press and release

the ON/OFF button.

4. Continue to hold the CAL button and the unit will power up and the display will flash

once.

5. When only the ‘F’ and ‘C’ icons appear on the display, release the CAL button. ‘C’ or

‘F’ (whichever was programmed earlier) will remain on the display.

6. Press and hold RESET for 3 seconds. ‘%MIN’ will appear in the display after the key

is released.

7. Press and hold RESET again for 3 seconds. ‘% MAX’ will appear in the display after

the key is released

8. Ensure that ‘%MAX’ is displayed then press CAL. ‘S’ will appear briefly and the

meter will return to normal operation.

9. Turn power off. The 75% calibration is now complete.

Note: If the salt at the bottom of the calibration bottles appears dry, the bottles

should be replaced.

* For testing purposes, the 40-minute stabilization period can be shortened.

However, for the most accurate calibration use the 40-minute period.

Models 445580 & 445582 Version 3.2 August 2003

BATTERY REPLACEMENT

Use a coin to remove the battery compartment cover on the rear of the meter. Replace the

2032 lithium battery installing it face (+) up in the battery compartment.

WARRANTY

EXTECH INSTRUMENTS CORPORATION warrants this instrument to be free of defects in parts and

workmanship for one year from date of shipment (a six month limited warranty applies on sensors and

cables). If it should become necessary to return the instrument for service during or beyond the warranty

period, contact the Customer Service Department at (781) 890-7440 ext. 210 for authorization or visit our

website at www.extech.com (click on ‘Contact Extech’ and go to ‘Service Department’ to request an RA

number). A Return Authorization (RA) number must be issued before any product is returned to Extech. The

sender is responsible for shipping charges, freight, insurance and proper packaging to prevent damage in

transit. This warranty does not apply to defects resulting from action of the user such as misuse, improper

wiring, operation outside of specification, improper maintenance or repair, or unauthorized modification.

Extech specifically disclaims any implied warranties or merchantability or fitness for a specific purpose and

will not be liable for any direct, indirect, incidental or consequential damages. Extech's total liability is limited

to repair or replacement of the product. The warranty set forth above is inclusive and no other warranty,

whether written or oral, is expressed or implied.

including the right of reproduction in whole or in part in any form.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Extech Instruments Termometro

Extech Instruments

Extech Instruments SD200 Manuale utente

Extech Instruments

Extech Instruments EA15 Manuale utente

Extech Instruments

Extech Instruments IR100 Manuale utente

Extech Instruments

Extech Instruments EasyView 10 Manuale utente

Extech Instruments

Extech Instruments IR300UV Manuale utente

Extech Instruments

Extech Instruments 445703 Manuale utente

Extech Instruments

Extech Instruments 421502 Manuale utente

Extech Instruments

Extech Instruments IR201A Manuale utente

Extech Instruments

Extech Instruments RH401 Manuale utente

Extech Instruments

Extech Instruments IR100 Manuale utente

Extech Instruments

Extech Instruments 421501 Manuale utente

Extech Instruments

Extech Instruments 42545A Manuale utente

Extech Instruments

Extech Instruments RH101 Manuale utente

Extech Instruments

Extech Instruments 42535 Manuale utente

Extech Instruments

Extech Instruments RH200W Manuale utente

Extech Instruments

Extech Instruments 42511 Manuale utente

Extech Instruments

Extech Instruments Extech 470 Manuale utente

Extech Instruments

Extech Instruments 42529 Manuale utente

Extech Instruments

Extech Instruments 42512 Manuale utente

Extech Instruments

Extech Instruments IR200 Manuale utente

Extech Instruments

Extech Instruments EA15-NIST Manuale utente

Extech Instruments

Extech Instruments TM20 Manuale utente

Extech Instruments

Extech Instruments HD500 Manuale utente

Extech Instruments

Extech Instruments 421504 Manuale utente

Manuali Termometro popolari di altre marche

Delton

Delton 981A Manuale utente

Baker

Baker MM2P Manuale utente

Tarmo

Tarmo 320281 Manuale utente

Citizen

Citizen CTD 504 Manuale utente

TFA

TFA 14.1500 Manuale utente

Vive

Vive DMD1010 Manuale utente

Gotemp

Gotemp THB4002 Manuale utente

GREISINGER

GREISINGER G 1202 Manuale utente

Amprobe

Amprobe TMD-53W Manuale utente

Trotec

Trotec BP10 Manuale utente

Radiance instruments

Radiance instruments RT616 Series Manuale utente

Eurolec

Eurolec IR151 Manuale utente

Scaneo

Scaneo TS42B Manuale utente

Sper scientific

Sper scientific 800043 Manuale utente

Microlife

Microlife NC 200 Manuale di istruzioni

Motorola

Motorola MBP69SN Guida alla configurazione

The MeatStick

The MeatStick The MeatStick Manuale utente

Hama

Hama TH35-A Manuale utente