Extreme Networks AP305C Manuale di installazione
AP305C and AP305CX Hardware User Guide
Read about and view specifications and compliance information for the AP305C and AP305CX in this topic.
Install the AP305C and AP305CX using this topic.
The AP305C and AP305CX are high-performance 802.11ax dual band access points.
Both are designed for indoor high-density environments that require HD video streaming and large file transfers.
The AP305CX has external antennas (sold separately), and an extended temperature range for industrial envir-
onments. These devices support IEEE 802.11ax Orthogonal Frequency-Division Multiple Access (OFDMA) multi-user
access.
For regulatory and compliance information, see "Regulatory Compliance Statements".
Safety Guidelines
Safety Guidelines
The safety information in this section applies to AP305C and AP305CX devices.
The following safety icons are used in these guidelines to identify the type of precaution:
This icon indicates a general caution. Failure to comply with a caution notification can res-
ult in damage to equipment.
This icon indicates an electrical caution. Failure to comply with an electrical notification
can result in serious injury or death, and extensive damage to equipment.
This icon indicates a laser caution. Failure to comply with a laser caution can result in ser-
ious injury.
The following table lists the safety precautions you should follow when installing your AP305C and AP305CX
devices.
Extreme Networks devices must be installed by a professional installer who is certified to
install these types of devices and to ensure that they are properly grounded and meet
applicable local and national electrical codes.
These devices are intended for indoor use only.
Do not install the device in an environment where the operating ambient temperature
might exceed the recommended ranges.
Warning: This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
AP305C and AP305CX Hardware Guide
1
For products available in the USA/Canada market, for the 2.4 GHz band, only channels 1-11
can be operated. Selection of other channels is not possible.
Changes or modifications made to this device that are not expressly approved by the
party responsible for compliance could void the user's authority to operate the equip-
ment.
Use only attachments and accessories specified by Extreme Networks.
These devices are not intended for use by persons (including children) with reduced phys-
ical, sensory, or mental capabilities, or with lack of experience of knowledge unless they
are given supervision or instruction concerning use of the devices by a person who is
responsible for their safety. Children should be supervised to ensure that they do not play
with the devices.
Electrostatic discharge (ESD) can damage equipment and impair electrical circuitry. ESD
damage occurs when electronic components are improperly handled and can result in
complete or intermittent failures. Be sure to follow ESD-prevention procedures when hand-
ling electronic components and equipment.
During operation, the surfaces of the AP305C and AP305CX can become hot. Use caution
when handling.
To meet federal radiation exposure requirements, these devices should be installed at a
minimum distance of 8" (20 cm) from people or animals.
Install the AP
You can mount the AP305C and AP305CX on a flat surface or wall, or on the rails of a standard dropped ceiling
grid. There is also an accessory mounting bracket that allows you to install the device in Armstrong-style dropped
ceilings (ordered separately).
The following sections describe how to install your AP305C and AP305CX devices and connect them to the net-
work.
Shipping Carton Contents
The AP305C and AP305CX shipping carton contains the following items:
AP305C or AP305CX chassis
Mounting bracket
Read Me card
Install the AP on a Ceiling Track
The AP305C and AP305CX ship with a mounting bracket that lets you easily install them on the rail of a standard
dropped ceiling grid. The following illustration shows how to attach the bracket to the ceiling rail, and then install
the AP on the bracket. This illustration shows an AP305C but the procedures are the same for both models.
AP305C and AP305CX Hardware Guide
2
Once the bracket is secure, install the AP using the following steps:
AP305C and AP305CX Hardware Guide
3
1. Align the red dot on the bottom of the AP with the red dot on the bracket.
2. Lift the AP straight up and keep the red dots aligned until the bracket is seated in the round depression on
the bottom of the device.
3. Rotate the AP clockwise until it clicks into place on the bracket.
Mount the AP on a Wall
Use the holes in the bracket as a template to mark the wall. Drill holes in the wall and attach the bracket to the
wall using wall screws and wall anchors if necessary. Attach the AP to the bracket in the same manner as shown
in the previous section. Install external antennas on AP305CX devices. Order antennas from Extreme Networks
(AH-ACC-ANT-KT).
Lock the AP
You can secure the AP using a Kensington® lock in the lock slot on the side of the device, or you can use a
secur-ity bracket and a crosshead screw or a security screw. Security brackets and screws can be ordered
separately from Extreme Networks (not available in Brazil).
Extreme Networks recommends a variety of Kensington locks. For more information, contact your sales rep-
resentative.
Connect the AP to the Network
Follow these steps to connect your AP305C or AP305CX to a standard AC wall socket and to the network.
1. Plug the AC power supply into the 12 V port on the device and into a standard wall socket.
2. Connect an Ethernet cable to the RJ45 port and to a modem or other network device.
3. After the AP receives power, it automatically tries to get network settings and contact HiveManager. This
process takes about five minutes. When you see the AP listed on the Devices page in the Monitor section of
the HiveManager GUI, the initial setup is complete and you can begin managing the AP with HiveManager.
Hardware Components
Status Light
The status light conveys operational states for system power, firmware updates, Ethernet and wireless interface
activity, and major alarms. The AP305C and AP305CX have a rectangular status light on the top right corner of
the chassis. At setup, this light cycles through the following sequence:
Slow-blinking White: The device is attempting to establish a connection or has established a
CAPWAP connection with HiveManager.
Fast-blinking White: The device is performing a HiveOS or HiveManager upgrade.
Steady White: The device has successfully established a CAPWAP connection and is operating normally.
Ethernet Port
The ETH0 port is autosensing 100/1000G BASE-T/TX Mbps, with IEEE 802.3af- or 802.3at-compliant PoE, and requires
Cat6 cable.
AP305C and AP305CX Hardware Guide
4
Console Port
The AP305C has a micro-USB Console port located on the bottom of the device.
Hardware Specifications
The following sections list radio, device, power, and environmental specifications for the AP305C and AP305CX.
Radio Specifications
Bluetooth BLE Beacon
2402 - 2480 MHz
Frequency Hopping Spread-spectrum (FHSS)
802.11a
5150-5250,
5725
-
5850
MHz
operating
frequency
Orthogonal
Frequency
Division
Multiplexing
(OFDM)
modulation
Rates
(Mbps):
54,
48,
36,
24,
12,
9,
6
with
auto
fallback
802.11b
2.4-2.48 GHz operating frequency
Direct-Sequence Spread-Spectrum (DSSS) modulation
Rates (Mbps): 11, 5.5, 2.1 with auto fallback
802.11g
2.4-2.48 GHz operating frequency
Orthogonal Frequency Division Multiplexing (OFDM) modulation
Rates (Mbps): 54, 48, 36, 24, 12, 9, 6 with auto fallback
802.11n
2.4-2.48
and
5.150-5.250,
5.725
-
5.850
GHz
operating
frequency
802.11n
modulation
Rates:
MCS0
-
MCS7
2x2
MIMO
radio
HT20/HT40
support
(HT40
is
for
5
GHz
only)
A-MPDU
and
A-MSDU
frame
aggregation
802.11ac
802.11ac
modulation
(256-QAM)
2.4
-
2.48
GHz
MCS0-9,
NSS=1-4
5.150-5.250,
5.725
-
5.850
GHz
operating
frequency
AP305C and AP305CX Hardware Guide
5
Rates: MCS0 - MCS9, NSS = 1-4
2x2 MIMO radio
VHT20/VHT40/VHT80 support (VT40 and VT80 for 5 GHz only)
802.11ax
5150-5250,
5725
-
5850
MHz
operating
frequency
2.4 - 2.48 GHz operation frequency
802.11ax modulation (1024-QAM)
Rates: MCS0 - MCS11, NSS = 1-4
OFDMA support
2x2 MU-MIMO
HE20/HE40/HE80 support (HE40 and HE80 for 5GHz only)
Transmit Power and Sensitivity Specifications
Output power may be limited by regulatory requirements.
Power: 2.4 GHz:
Tolerance +2/-2 dB @25°C
Channel Data Rate Power (dBm)
11b 1,2,5.5,11 18
11g 54 Mbps 15
48 Mbps 16
36 Mbps 17
6 Mbps 18
HE20 MCS 0,1,2 18
MCS 3 17
MCS 4, 5 16
MCS 6,7 15
MCS 8,9 14
MCS 10,11 12
AP305C and AP305CX Hardware Guide
6
Channel Data Rate Power (dBm)
2.4 G Sensitivity
11b 1 Mbps -99
11 Mbps -90
11g 6 Mpbs -96
36 Mpbs -84
48 Mbps -80
54 Mbps -78
HE20 MCS 0 -95
MCS 1 -91
MCS 2 -89
MCS 3 -86
MCS 4 -83
MCS 5 -79
MCS 6 -77
MCS 7 -76
MCS 8 -72
MCS 9 -70
MCS 10 -67
MCS 11 -64
Power: 5 GHz:
Mode Data Rate Power (dBm)
11a 54 Mbps 17
48 Mbps 17
AP305C and AP305CX Hardware Guide
7
Mode Data Rate Power (dBm)
36 Mbps 18
6 Mbps 19
HE20 MCS 0, 1, 2 19
MCS 3, 4 17
MCS 5, 6 16
MCS 7, 8 15
MCS 9 14
MCS 10 13
MCS 11 12
HE40 MCS 0, 1, 2 17
MCS 3, 4, 5 16
MCS 7, 15, 23 14
MCS 6, 7, 8 15
MCS 10 13
MCS 11 12
HE80 MCS 0,1,2 17
MCS 3,4,5 16
MCS 6,7,8 15
MCS 9 14
MCS 10 13
MCS 11 12
Sensitivity
11a 6 Mbps -94
36 Mbps -83
48 Mbps -79
AP305C and AP305CX Hardware Guide
8
Mode Data Rate Power (dBm)
54 Mbps -77
11n HE20 MCS 0 -94
MCS 1 -91
MCS 2 -88
MCS 3 -86
MCS 4 -82
MCS 5 -78
MCS 6 -77
MCS 7 -75
MCS 8 -71
MCS 9 -69
MCS 10 -66
MCS 11 -63
11n HE40 MCS 0 -92
MCS 1 -88
MCS 2 -86
MCS 3 -83
MCS 4 -80
MCS 5 -76
MCS 6 -74
MCS 7 -73
MCS 8 -69
MCS 9 -67
MCS 10 -63
AP305C and AP305CX Hardware Guide
9
Mode Data Rate Power (dBm)
MCS 11 -60
HE80 MCS 0 -88
MCS 1 -85
MCS 2 -83
MCS 3 -80
MCS 4 -77
MCS 5 -73
MCS 6 -71
MCS 7 -69
MCS 8 -66
MCS 9 -64
MCS 10 -60
MCS 11 -57
Tolerance +2/-2 dB @25° C
Mode Data Rate Power (dBm)
11a 6 Mbps 19
36 Mbps 18
48 Mbps 16
54 Mbps 15
11n HE20 MCS 0,1, 2, 3, 4, 8, 9, 10, 11 19
MCS 13, 21 18
MCS 14, 22 16
MCS 15, 23 15
MCS 12, 16, 17, 18, 19, 20 19
AP305C and AP305CX Hardware Guide
10
Altri manuali per AP305C
4
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Extreme Networks Punto di accesso wireless
Extreme Networks
Extreme Networks Altitude 4511 Manuale utente
Extreme Networks
Extreme Networks Altitude 350-2d AP Manuale utente
Extreme Networks
Extreme Networks ExtremeWireless AP560i Manuale utente
Extreme Networks
Extreme Networks Altitude 4532 Series Manuale utente
Extreme Networks
Extreme Networks AP305C Manuale di installazione
Extreme Networks
Extreme Networks ExtremeWireless AP3935i Manuale utente
Extreme Networks
Extreme Networks Altitude 3500 Series Manuale di installazione e funzionamento
Extreme Networks
Extreme Networks ExtremeMobility AP560i-FCC Manuale utente
Extreme Networks
Extreme Networks ExtremeWireless AP560i Manuale utente
Extreme Networks
Extreme Networks ExtremeWireless AP410i Manuale utente
Extreme Networks
Extreme Networks ExtremeWireless AP3000X Manuale utente
Extreme Networks
Extreme Networks ExtremeWireless AP460i Manuale utente
Extreme Networks
Extreme Networks AP60C Manuale di installazione
Extreme Networks
Extreme Networks Extreme Wireless WSAP3825i Manuale utente
Extreme Networks
Extreme Networks ExtremeWireless WS-AP3965i-FCC Manuale utente
Extreme Networks
Extreme Networks ExtremeWireless AP3935e Manuale utente
Extreme Networks
Extreme Networks ExtremeWireless AP510i Manuale utente
Extreme Networks
Extreme Networks Altitude 450 Manuale utente
Extreme Networks
Extreme Networks ExtremeWireless 31012 Manuale utente
Extreme Networks
Extreme Networks ExtremeWireless AP5010 Manuale utente
